User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–54
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
4. Connect the end coming from the antenna subsystem to the splitter input (S)
connector.
5. Connect the end going to TPC1 of the RFU to one of the output ports of the
splitter, one or two.
6. Run a new coax cable (length is installation specific) from the unused splitter
output port to BP-12 of the ARINC 600 connector of the HSD tray assembly.
(l) Cooperative Mode Connection Details
The tables in this section provide all top, middle, and bottom plug connection
details for Cooperative Mode installations.
Table 3–28. Receive Path Parts Requirements – Cooperative Mode
Item Manufacturer PN
EMS
SATCOM
PN
Description
RF Splitter ZAPD-2-TNC 32800004 Mini-Circuit, 2-way 0°, TNC,
Splitter
Receive Coax 432101 – ECS, Coax Cable, 0.130 O.D.,
50
Ω, 17.5 dB/100 ft @ 1.5 GHz
Connector (@
Splitter)
CTS522 – ECS, TNC, Straight Plug
Connector (@
BP12)
P522 – ECS, ARINC 600, Size 5, Socket
Table 3–29. Cooperative Mode ARINC 600 Top Plug Connection Details
I/O
From
Top Plug
Signal Name To Description
I/O
1A to 1D Multi-Control IN and
BITE OUT
As per Collins
documentation
Multi-Control and BITE
I
2A BSU Top/Port BITE A SDU, MP7G ARINC Tx-HI BITE
From Top/Port BSU
I
2B BSU Top/Port BITE B SDU, MP7H ARINC Tx-LO BITE
From Top/Port BSU
I
2C BSU STBD BITE A Mechanically Steered
1
Antenna (MA):
Not
required
Other Antenna
2
(OA):
SDU, MP7J
ARINC Tx-HI BITE
From STBD BSU
I
2D BSU STBD BITE B MA: Not required
OA
: SDU, MP7K
ARINC Tx-LO BITE
From STBD BSU
O
2E OUT SDU Crosstalk
A
SDU, MP12A ARINC 429
O
2F OUT SDU Crosstalk
B
SDU, MP12B ARINC 429