User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–59
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Note: At SDU#1, connect TP12E to GND
D. Section IV: Multi-Channel Configuration Installation
(1) Multi-Channel Configuration Installation Wiring Notes
This section provides detailed information on the external interface and system
connections involved in the installation of an HSD-128 and HSD-X transceivers for
Multi-Channel configuration operation.
Table 3–33, Table 3–34, Table 3–35, and Figure 3–38 illustrate the interconnection
and contact assignment details of a Multi-Channel HSD configuration.
This section provides detailed information on cable loss considerations, the splitter
for the receive path, and the combiner for the transmit path.
I
7A 10BASE-T Rx+ Ethernet 10BASE-T,
RJ45-3
User Data,
Ethernet 10BASE-T
(Available in models
1110-A-0150,
1110-A-0160, and in
units with Service
Bulletin, 1110-SB-0004
accomplished)
I
7B 10BASE-T Rx- Ethernet 10BASE-T,
RJ45-6
O
7C 10BASE-T Tx+ Ethernet 10BASE-T,
RJ45-1
O
7D 10BASE-T Tx- Ethernet 10BASE-T,
RJ45-2
O
C1 RF Tx Output Antenna
Subsystem-DLNA
Coax Cable, RF
Transmit
Table 3–31. Cooperative Mode ARINC 600 Bottom Plug Connection Details
I/O
From
Bottom
Plug
Signal Name To Description
I
2 +28 V dc HOT Aircraft Power Source,
HOT
+28 V dc supply
I
3 +28 V dc Rtn GND Aircraft Power Source,
Rtn
I
8 Chassis GND Aircraft Ground Aircraft Chassis
Ground
I
1 115 V ac HOT Aircraft Power Source,
HOT
115 V ac 400 Hz supply
I
7 115 V ac COLD Aircraft Power Source,
COLD
I
12 RF Rx Input RF Rx Splitter output port RF Receive from
Antenna Subsystem
Table 3–30. Cooperative Mode ARINC 600 Middle Plug Connection Details
I/O
From
Middle
Plug
Signal Name To Description