User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–76
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
O
1F LED Common Remote Status LED
Panel, and closed side of
N.O. Remote Reset
Switch
LED Common
O
1G Maint Port Tx
(OUT)
Maint Port serial data,
DB9S-2
Maintenance computer,
for “Remote” access
I
1H Maint Port Rx (IN) Maint Port serial data,
DB9S-3
I/
O
1J Maint Port Signal
Ground.
Maint Port serial data,
DB9S-5
O
3A CC (channel
card)#2 Rx
DTE-1B, DB9S-2 or
DB25P-3
User Mobile Packet Data
(MPDS), RS-232,
DTE-1B
I
3B CC #2 Tx DTE-1B, DB9S-3 or
DB25P-2
I
3C CC #2 RTS DTE-1B, DB9S-7 or
DB25P-4
O
3D CC #2 CTS DTE-1B, DB9S-8 or
DB25P-5
I
3E CC #2 DTR DTE-1B, DB9S-4 or
DB25P-20
O
3F CC #2 DSR DTE-1B, DB9S-6 or
DB25P-6
O
3G CC #2 CD DTE-1B, DB9S-1 or
DB25P-8
O
3H CC #2 RI DTE-1B, DB9S-9 or
DB25P-22
I/
O
3J CC #2 SGND DTE-1B, DB9S-5 or
DB25P-7
I
4G BRI Rx+ ISDN, RJ45-3 User Data, ISDN–2
Refer to "User Interfaces
– Multi-Channel" on page
3-67
I
4H BRI Rx- ISDN, RJ45-6
O
4J BRI Tx+ ISDN, RJ45-4
O
4K BRI Tx- ISDN, RJ45-5
I
5G to 5K I/O CONFIG Pins
1 to 4
See Figure 3–8 System Data I/O Mode
Configurations
Table 3–40. HSD-128 Multi-Channel Configuration, ARINC 600 Middle Plug
Connections
I/O
From
Middle
Plug
Signal Name To Description