User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–9
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(5) Menu Descriptions
This section describes the menus and menu items available in the HSD maintenance
utility program in Level 1 access (using the MENU password) and Level 2 access
(using the MAINT password) based on control processor software version 4.5 and
7.0. The differences between version 4.5 and 7.0 are noted within the examples. All
menus and items that appear in Level 1 also appear in Level 2.
No additional menus or menu items were added with the release of Version 7.5,
Control Processor software.
Note: Depending on the version of software and configuration mode installed, the
actual menus and screen displays in “live” systems may differ slightly from
the illustrations provided in this manual.
(a) Level 1 Menu Selections (Password: MENU)
Figure 4–5 shows all menus available to Level 1 users for control-processor
software version 4.5 to 7.0. Menu items added or changed in version 7.0, control
processor software are highlighted in bold text. No additional menus or menu
items were added with the release of Version 7.5, Control Processor software.
Figure 4–5. Level 1 MENU Selections
Note: Menu 3, item O ‘list ORT’ was added in control processor software version
7.0.
MENU1 FIRMWARE V7.0
Y explain hpa error status
<CTRL> N next menu <CTRL> O previous menu = select reports
MENU2 FIRMWARE V7.0
N annotate log file L re-enter logon password
V get firmware versions Z reset HSD-128
<CTRL> N next menu <CTRL> O previous menu = select reports
MENU 3 FIRMWARE V7.0
L list EEPROM S list event log
F list call log O list ORT
<CTRL> N next menu <CTRL> O previous menu = select reports
MENU 4 FIRMWARE V7.0
Q channel card forward ID's
<CTRL> N next menu <CTRL> O previous menu = select reports