User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–27
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(f) Menu 13
Menu 13 items are used to query and debug systems with Data I/O Card 2
(available on HSD models 1110-A-0150 and 1110-A-0160 or other HSD models
via service bulletin 1110-SB-0004). Menu 13 is the same in all control processor
software versions 4.5 and later.
Figure 4–22 shows the HSD maintenance utility program Menu 13 screen
display. Table 4–14 describes the items available in Menu 13.
Figure 4–22. Menu 13 Screen Display
B: simul sb ACU
status
• Used to enter the starboard antenna gain in dB and the
message rate in Hz
N: deactivate antenna
status words
• Used to deactivate all set antenna status words
G: simul INS long
• Allows user to simulate aircraft longitude by overriding
the data received from the aircraft INS
T: simul ins true track
• Allows user to simulate true track by overriding the data
received from the aircraft INS
R: simul INS roll
• Allows user to simulate aircraft roll by overriding the data
received from the aircraft INS
A: activate all simul
words
• Activates all input simulate parameters overriding the INS
data received from the aircraft
• Lat and Long values from the EEPROM values set in
Menu 3
C: simul port ACU
status
• Used to enter both the port antenna gain in dB and the
message rate in Hz
M: activate antenna
status words
• Used to activate all set antenna status words
MENU 13 FIRMWARE Vx.x
T query DATA IO elapsed time V query DATA IO version
S query DATA IO services C query DATA IO config pins
F DATA IO fault logging level X DATA IO console mode
<CTRL> N next menu <CTRL> O previous menu = select reports
Table 4–13. Menu 10 Item Descriptions
Menu Item Item Description