User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–32
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Figure 4–27. HSD Maintenance Utility Program: Report Items (Version 7.0)
1 OFF messages to channel card #1 13 OFF messages to channel card #2
2 OFF hex output to channel card #1 14 OFF hex output to channel card #2
3 OFF responses from channel card #1 15 OFF responses from channel card #2
4 OFF hex input from channel card #1 16 OFF hex input from channel card #2
5 OFF channel #1 misc info 17 OFF channel #2 misc info
6 OFF sb antenna arinc input 18 OFF port antenna arinc input
7 OFF sb antenna maintenance word 19 OFF port antenna maintenance word
8 OFF sb antenna status word 20 OFF port antenna status word
9 OFF channel card call status 21 ON call codes
10 OFF channel card THA codes 22 OFF spot beam selection
11 OFF channel card errors 23 OFF standard output
12 OFF INS input 24 OFF doppler, antenna az/el
25 OFF HPA arinc i/o 37 OFF combined-mode spoofed output
26 OFF HPA error status 38 OFF combined-mode power allotment
27 OFF HPA/channel card backoffs 39 OFF combined-mode debugging
28 OFF miscellaneous digital inputs 40 OFF enthusiastic combined-mode
debug
29 OFF channel card A_AM msgs 41 OFF delta combined-mode debugging
30 OFF multi-control arinc bus 42 OFF raw arinc data from ITS
31 OFF ocean region info 43 OFF high-precision hpa power
32 OFF hex input from data i/o 44 OFF hpa calibration (gain droop)
33 OFF hex output to data i/o 45 OFF combined mode ocean region debug
34 OFF input from data i/o 46 OFF hpa resets
35 OFF changes in multi-control bus 47 OFF channel card temperature
36 OFF unit test call setup 48 OFF hexadecimal INS input
49 OFF main loop latency 61 OFF non-zero channel card power
50 OFF main loop timing 62 OFF m4 availability status
51 OFF one second tick 63 OFF enthusiastic output to RC SDU
52 OFF extended call codes 64 OFF channel card frequencies
53 OFF standalone w/o ant data 65 OFF enthusiastic messages from HPA
54 OFF RC SDU time and date 66 OFF channel card boot sequence
55 OFF RC arinc i/o (hex) 67 OFF debug honeywell combined mode
56 OFF RC misc arinc i/o (ascii) 68 OFF CFDS debugging
57 OFF RC EIRP 69 OFF vt100 scenario
58 OFF RC SAT-906 Status 70 OFF HCM input
59 OFF RC Satellite Position 71 OFF HCM power level
60 OFF debug channel card power 72 OFF DATA I/O events
73 OFF HCM power control 85 OFF debug CC#2 channel card power
74 OFF TIM HCM power debugging 86 OFF Channel card rx attenuation
75 OFF HCM BITE 87 OFF interworking report
76 OFF HSD-X arinc messages 88 OFF all words to SDU
77 OFF HSD-X net configuration 89 OFF debug call teardown
78 OFF vt100 eirp/power 90 OFF debug cc backoff
79 OFF dialtone debugging 91 OFF HSD frequencies
80 OFF RC CC#2 SDU time and date 92 OFF intermod debugging
81 OFF RC CC#2 arinc i/o (hex) 93 OFF spot beam debugging
82 OFF RC CC#2 misc arinc i/o (ascii) 94 OFF vt100 channel card info
83 OFF RC CC#2 EIRP 95 OFF vt100 debugging
84 OFF RC CC#2 SAT-906 Status