User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–49
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
The procedures assume that the technical personnel are familiar with the test
equipment used and can operate the equipment to produce the required inputs and
obtain the required results (indications). Refer to the detailed operating procedures
and descriptions of the HSD Maintenance Utility Program included in this section.
CAUTION: Only Authorized Technical Personnel, trained in general aviation
workmanship, that have a basic understanding of SATCOM systems,
should proceed with the Operational and Diagnostic test procedures
presented in this manual.
CAUTION: Changes to some Menu functions may seriously degrade system
operation.
Note: This manual describes the basic maintenance utility program functions,
menus, and reports required for the testing and fault isolation procedures
presented in this section. Please consult EMS SATCOM support personnel
before entering any unfamiliar menu selections not described in this manual.
Note: Using a terminal emulation program, open a log file and save all test results
for future reference and test records. This section includes detailed user
instructions on opening and saving log files using the HSD maintenance utility
program.
Note: The procedures presented in this section aid the technical personnel in
upgrading, maintaining, or troubleshooting an HSD system. Maintenance
does not imply lubrication or adjustment activities.
REFERENCE INFORMATION: Refer to the Outline and Installation drawings and the
Interconnection diagrams presented in
"Installation" on page 3-1 for additional
information.
(2) Test Setup Procedure
The test setup procedure is presented in Table 4–21. Refer to "Connection
Requirements" on page 4-4 for detailed connection of test equipment and operating
instructions for the HSD maintenance utility program.
Table 4–21. Test Setup Procedure
STEP ACTION
0 Ensure that the HSD or HSD-X transceiver is neither powered up nor
connected to a power source before proceeding.
0 If a remote access has not been installed: on the front panel of the HSD or
HSD-X transceiver, remove the maintenance-port-connector cover.
0 Connect a cable to the HSD or HSD-X front-panel or remote maintenance
port connector.
0 Connect the other end of the cable to a computer’s serial port.
0 Open a log file to capture all test data.