User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 1–6
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(2) Operational Software Part Numbers
Table 1–4 provides a list of software part numbers for the HSD transceiver. Table 1–
5 provides a list of software part numbers for the HSD-X transceiver.
(3) Operational Mode Software Requirements
This section describes the software requirements and compatibility issues for each
mode of operation, including Multi-Channel configurations.
(a) Stand-Alone Mode
For Stand-Alone Mode installations, the minimum and recommended
requirements for software are shown in
Table 1–6.
Table 1–4. HSD Operational Software
EMS SATCOM Part
Number
Description
LI-1110-10136 HSD-64/128 Software Configuration
1110-A-0082 Aero Channel Card Software
1110-A-0048 Assembly Firmware Control Processor
1110-A-0109 Firmware HPA 28 V dc
1110-A-0110 Firmware HPA 115 V ac
1110-A-0129 Firmware HPA 28 V dc Revised Board
1110-A 0141 Firmware HPA 115 V ac Revised Board
1110-A-0100 HSD Data I/O Firmware Assembly (Only applies to units
with Data I/O Card Type 2 installed)
Table 1–5. HSD-X Operational Software
EMS SATCOM Part
Number
Description
LI-1110-10181 HSD-X Software Configuration
1110-A-0082 Aero Channel Card Software
1110-A-0420 Assembly Firmware Control Processor
1110-A-0115 HSD-X Data I/O Firmware
1110-A-0085 M4 Combined Pic and Bootloader
Table 1–6. Stand-Alone Mode Minimum Software Requirements
Unit
Part
Number
Software
PN
Software
Type
Minimum
Software
Req’t
Recommended
Software
HSD-128 1110-A-0001
1110-A-0060
1110-A-0150
1110-A-0160
1110-A-0048 Control
Processor
4.1 7.5 (or later)
1110-A-0082 Channel
Card
C24 C41 (or later)