Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
Table 6-1. L1, L2 and L3 Codes (Cont)
Repair actionLog type
L3L2L1
DescriptionCode
Descrip-
tion
Code
Descrip-
tion
Code
could be part of
normal power down
Status
Message
Power Supply
Internal fault
2
Power
supply
1BUC-PA2
Note: this can be a
false positive prior to
BLv7
Status
Message
Buc LockLoss:
Transmit BITE
Status
1BUC2BUC-PA2
Note: this can be a
false positive prior to
BLv7
Status
Message
Buc LockLoss:
Transmit BITE
Status
2BUC2BUC-PA2
Status
Message
PA Overdriven:
Transmit BITE
Status
2
Power
Amplifier
4BUC-PA2
Reboot the system, if
problem persists,
replace BUC-PA
Critical FaultsFlash Fault1
Monitor and
Control
5BUC-PA2
Reboot the system, if
problem persists,
replace BUC-PA
Critical FaultsRAM Fault2
Monitor and
Control
5BUC-PA2
Status
Message
Watchdog reset3
Monitor and
Control
5BUC-PA2
Status
Message
Standard
Electronic
Information
A
Operational
Information
FABUC-PA2
Status
Message
Honeywell
Electronic
Information
B
Operational
Information
FABUC-PA2
Status
Message
Watchdog1ResetFCBUC-PA2
Status
Message
Software
Command
2ResetFCBUC-PA2
Status
Message
SW exception4ResetFCBUC-PA2
Status
Message
Power Cycle Or
Reset Pin
5ResetFCBUC-PA2
Dataload the BUC-PA
software
Critical Faults
HW SW
Compatibility
1
Software
Configuration
FDBUC-PA2
Dataload the BUC-PA
software
Critical Faults
PRIMARY
IMAGE
CORRUPTION
Warning
4
Software
Configuration
FDBUC-PA2
Page 6-25
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal