Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
Table 6-1. L1, L2 and L3 Codes (Cont)
Repair actionLog type
L3L2L1
DescriptionCode
Descrip-
tion
Code
Descrip-
tion
Code
Status
Message
Software
Command
2ResetFCKANDU6
Reboot the system, if
persist, replace the
KANDU
Critical FaultsSW exception4ResetFCKANDU6
Status
Message
Power Cycle Or
Reset Pin
5ResetFCKANDU6
Dataload KANDU
Critical Faults
HW SW
Compatibility
1
Software
Configuration
FDKANDU6
Dataload KANDU
Critical Faults
LRU SW
Compatibility
2
Software
Configuration
FDKANDU6
Dataload APM
configuration filesCritical Faults
Configuration
parameter
missing
3
Software
Configuration
FDKANDU6
Dataload KANDU
Critical Faults
PRIMARY
IMAGE
CORRUPTION
Warning
4
Software
Configuration
FDKANDU6
Dataload KANDU
Critical Faults
LRU PRI-SEC
IMAGE
MISMATCH
6
Software
Configuration
FDKANDU6
Status
Message
DataLoad7
Software
Configuration
FDKANDU6
Status
Message
Data Loader
Connected
8
Software
Configuration
FDKANDU6
Status
Message
Data Loader
Disconnected
9
Software
Configuration
FDKANDU6
Run EUI tool on OAE
Critical Faults
Invalid OAE
Configuration
Data
80
Software
Configuration
FDKANDU6
Re-run cable
calibration. For
Modman x.5
(ChinaSat)If problem
with running cable
calibration, reload TM
configuration files
Warning
Missing
Transmit Cable
Calibration Data
81
Software
Configuration
FDKANDU6
Status
Message
Operating
Image List
A
Software
Configuration
FDKANDU6
Page 6-42
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal