Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
Table 6-1. L1, L2 and L3 Codes (Cont)
Repair actionLog type
L3L2L1
DescriptionCode
Descrip-
tion
Code
Descrip-
tion
Code
Check Signal path
from Modman to BUC
Critical FaultsTX IF1Unknown0
RF TX
ModMan to
BUC-PA/
BUC-HPA
B0
Check Signal path
from Modman to BUC
Critical Faults50 MHz Ref2Unknown0
RF TX
ModMan to
BUC-PA/
BUC-HPA
B0
Check Signal path
from BUC to OAE
Critical FaultsTX ka Band1Unknown0
RF TX
BUC-PA/
BUC-HPA
to OAE
B1
Check signal path
from OAE to BUC, and
BUC to Modman, also
ensure proper APM
(systemconfig) is
loaded
Critical FaultsRX Cabling1Unknown0RF RXB2
Check for clear line of
sight
Status
Message
GLOBAL BEAM
LOCK
2Unknown0RF RXB2
Check IF TX line
between External
modem and BUC
HPA. In the case that
external modem mode
is not desired, change
back to internal
modem mode
warning50 MHZ REF1Unknown0
Ext 50MHz
IFIB BUC-
PA Tx
BB
Status
Message
LRU Menu
Access -
Maintenance
11Unknown0FMA4
3. System Fails Post-Installation Checks
A. To make sure that the system is correctly installed, do as follows:
(1) Make sure that the APM has been correctly configured and loaded. Refer to ARINC 615A
Software Data Load Process and this section to access the GUI to check that the correct
APM version is installed.
(2) Make sure that all the LRUs and connections have been correctly installed.
(a) Do continuity checks on wiring, validate communication cabling for Tx, Rx signal
integrity via cable analyzers, test RF cables with specialized RF cable testers, and
do power on and ground checks with LRUs disconnected for the check.
Page 6-80
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal