Specification

316
Dynamic Coefficient of Friction (DCOF) - ANSI A137.1
The coefficient of friction measurement is an evaluation of a tile surface under
known conditions using a standardized sensor material. It provides a useful
comparison of tile surfaces, but it does not predict the likelihood a person
will or will not slip on a tile surface. DCOF (Dynamic Coefficient of Friction)
specifically tests the friction of an object that is already in motion (kinetic).
The BOT3000 (Binary Output Tribometer) and BOT3000E are machines that
run approximately 8” across a surface, measure the DCOF of the tile and provide
a digital reading with the results. Because these machines are automated, they
are able to objectively measure the slip resistance and most importantly, provide
repeatable results. ANSI A137.1 recommends, but does not require, a wet result
of 0.42 or greater for interior surfaces that are intended to be walked on wet.
Glazed Porcelain
Glazed porcelains are manufactured to have superior breaking strength, scratch, wear,
dirt and water resistance. Porcelains are a type of ceramic with a much more refined
body and are dry pressed. The body of a porcelain has a <0.50% water absorption rate
while the glaze applied to the surface of the tile is impermeable. All porcelain tiles are
fired in a kiln just like ceramics but they are fired under higher heat for longer periods
of time and under pressure, which adds to the density and durability of the tile.
Glazed Ceramic
Glazed ceramics offer stain and moisture resistance compared to most unglazed
clay products. Ceramic tiles are made from a combination of clays, polymers and
fine powders such as, sand and feldspar. The body of a ceramic is oen referred to
as a “bisque” or “clay.” Ceramics have either a red or white body, which is typically
determined by the region the clay was mined from. The body of a ceramic has a >0.50%
water absorption rate, while the glaze applied to the surface of the tile is impermeable
aer firing, making it a low maintenance and durable wall or flooring surface.
Glazed Body Match
Glazed products typically have a white or red body, however, a glazed body match tile
has a tinted body to match the top glaze color. With glazed porcelain and ceramic tiles,
the hardness and abrasion resistance of the glaze will determine product suitability for
a particular application. If the body matches the glaze, chips and scratches will not be
as evident making a colored body more desirable.
Through-Body
Through-body porcelains are unglazed and exhibit the same color and paern all
the way through the tile. The pressed dry powder method is also known as Single
Charging. During this process, fine powders are colored during the pressing stage of
production and the pigments are consistent throughout the body of the tile. Through-
body porcelain tiles are typically very dense, extremely durable and desirable in
applications subject to heavy abrasion. The advantage to using through-body products
is the ability to bullnose custom trims on site and ability to buff out any light scratching.
Soluble Salt Porcelain
Soluble Salt porcelain is a through-body porcelain product in which chemicals are
applied using various silk screens or sprayers prior to firing. Metal oxide salts react
with the porcelain body, resulting in various colors. This topical treatment is not
considered a glaze; the surface coloring is achieved through a reaction of chemicals
on the surface, triggered during the firing stage.
Double Loaded
Double Loaded, also known as Double Charging, is formed by fusing two layers of
porcelain together. The base layer of porcelain is bonded to an aesthetic top layer
where the coloring is already infused into the micro-powders. Once these two layers
are pressed together, they are fired to form one solid tile. No glaze is applied to the
top surface. These tiles can oen be bullnosed just like a through-body as the top and
boom layers are similar in color. The thickness of the top layer is significant enough
where the performance characteristics would be the same as a through-body tile.
Shade Variation
Shade variation is the tile’s range from complete inconsistency to a more random
appearance. Below is an overview of color and shading of individual tile selections.
V0 - Monochromatic - Very uniform, monochromatic color
V1 - Low - Consistent color within each tile and from tile to tile
V2 - Medium - Color variation within each tile
V3 - High - Some variation from tile to tile, and within each tile
V4 - Random - Considerable variation from tile to tile
V0 V1 V2 V3 V4