Belmont Freestanding Lattice Screen W/ Planter Box (45 1/2"H X 42" W X 11 1/4" L) 45 min Approximate assembly time Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com VER.
EC18005 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT j Check the inside of the larger pieces in your box for other materials packed inside. j When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. j We recommend an area approximately 5’x 8’ for unobstructed assembling. j You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18005 41 in 2 3/4 in 44 1/2 in 45 1/2 in 3 in 2 in 7 1/4 in 10 1/2 in 42 in 7 1/4 in 11 1/4 in www.encloscreens.
EC18005 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B C Side Board (2) 7/8" x 71/4" x 71/4" Long Board (2) 7/8" x 71/4" x 38" Floor Board (1) 7/8" x 71/4" x 38" D E F Floor Support (3) 7/8" x 11/2" x 7" Post Cap (4) Short Post (2) 3" x 3" x 10" G H I Long Post (2) 3" x 3" x 44" Arched Top Rail (1) 7/8" x 81/2" x 38" Bottom Rail (1) 7/8" x 3" x 38" J K L Horizontal Slat (7) Slat 1 (6) 1/4" x 11/4" x 38" Slat 2 (1) 1/4" x 11/4" x 331/2" Vertical Picket (11) Picket 1 (3) 5/8" x 5/
ASSEMBLY INSTRUCTIONS EC18005 STEP 2: ASSEMBLE PLANTER BOX STEP 2.1 STEP 2.2 1. Lay out the Short Posts (F) and slide (1) Long Board (B) into the post channels. 2. Rotate the posts and board 180 degrees. Drive (2) 2 1/2" Self-Drilling Stainless Steel Screws (L) through the predrilled holes in the posts as shown below. b Repeat step 2.1 with the Long Posts (G). Ensure that the long board is touching the back of the post channels.
EC18005 ASSEMBLY INSTRUCTIONS STEP 2.3 1. Slide the Side Boards (A) between the two assembled planter sections. 2. Drive (4) 21/2" self-drilling stainless steel screws through the pre-drilled holes on the inside face of the posts to secure the side boards. 1 2 Ensure that the side boards are touching the back of the post channels. A STEP 2.4 1. Slide the notch of the Floor Supports (D) over the inside wall of the routed section of the long boards. 2.
ASSEMBLY INSTRUCTIONS EC18005 STEP 3: ASSEMBLE LATTICE SECTION STEP 3.1 1. Arrange the Vertical Pickets (K) as shown with the stickers at the bottom. 2. Insert Horizontal Slat 1 (J) into the lowest holes in the vertical pickets. 3. Insert (5) more of the horizontal slat 1 and (1) horizontal slat 2 as shown below. Note: At the end of this step, the horizontal slat 2 should not be going through the number 5 vertical pickets.
EC18005 ASSEMBLY INSTRUCTIONS STEP 3.3 1. Slide the Arched Top Rail (H) down over the vertical pickets and over the top horizontal slat. H 8 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18005 STEP 4: INSTALL LATTICE SECTION STEP 4.1 1. Slide the assembled lattice section into the inner post channels of the long posts until the bottom rail is 2" above the planter box. 2. Drive (4) 21/2" self-drilling stainless steel screws into the back of the tall posts as shown below to secure the lattice section. 1 2 2 in STEP 5: INSERT POST CAPS STEP 5.1 Fit (4) Post Caps (E) over the short and tall posts. www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS VER.
