Highland Vinyl Privacy Lattice Screen (2-Pack) 36" W x 57" H 45 min Approximate assembly time Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS ZP19047 www.encloscreens.com VER.
ZP19047 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS ZP19047 Detailed Product Dimensions & Specifications 36 in 54 1/2 in 2 1/4 in 16 in 57 in 2 1/4 in www.encloscreens.
ZP19047 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B H Post Cap (4) I D C ¾" Self-Tapping Stainless Steel Screw (16) Bag A Post Anchor (4) ¾” x 1¼” x 20” 1" Self-Drilling Stainless Steel Screw (4) Bag B J Vertical Picket (20) ⅝” x ⅝” x 52½” Post (4) ⅞” x 1½” x 56½” Joiner Clip (2) K E Horizontal Picket (28) ¼” x 1¼” x 32½” F G Horizontal Rail (4) 1½” x 1½” x 36” 4 Rail End Cap (8) (4 loose, 4 installed) 1/8" Steel Drill Bit (1) www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19047 STEP 2: ASSEMBLE THE PICKET GRID STEP 2.1 Take (10) Vertical Pickets (C), and arrange them as shown. C Note: Make sure the routed holes for each vertical picket line up. STEP 2.2 Insert (14) Horizontal Pickets (E) through the routed holes in the vertical pickets. E Note: It may take some light force to insert horizontal pickets through the routed holes. www.encloscreens.
ZP19047 ASSEMBLY INSTRUCTIONS STEP 3: ATTACH THE POSTS STEP 3.1 Starting with one Post (D), slowly slide the horizontal pickets, one by one, into the routed holes in the post. Do the same for the second post, ensuring that the tabs of the posts are at the same end of the screen as shown. Note: The end of the post with the plastic tab will be the top of the screen. D STEP 4: ATTACH THE RAILS STEP 4.
ASSEMBLY INSTRUCTIONS ZP19047 STEP 4.2 STEP 4.3 Ensuring the routed holes are facing up, slide one rail over the bottom of the posts. Slide the rail up and guide the vertical pickets into the routed holes. Continue sliding the rail up until the pre-drilled holes in the rail and posts align. 1. Slide the Post Anchors (B) into the bottom of the post. 16" of post anchor should be visible. 2.
ZP19047 ASSEMBLY INSTRUCTIONS STEP 5: INSTALL THE SCREENS STEP 5.1 Repeat Steps 2-4 to assemble the second screen. STEP 5.2 Move the screen to its final location, and identify where the posts will be located. Attempt to push the unit into the ground as illustrated. All 16” of the post anchors should be inserted into the ground, so they are no longer visible. 2 1. If your ground is too hard, loosen the top 6” or 7” of the ground with a claw hammer as illustrated. 2. Add water to the loosened soil. 3.
ASSEMBLY INSTRUCTIONS ZP19047 STEP 5.3 Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com). 2. Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated. 3. Push the panel posts into the holes. 1 2 www.encloscreens.
ZP19047 ASSEMBLY INSTRUCTIONS STEP 5.4 Level the screen as necessary, backfill excavated dirt, and tamp down. Level STEP 5.5 Optional: If your ground is very hard, you may need to dig a single hole large enough to accommodate one post from each panel. This hole should be approximately 8” in diameter and 16” deep. Backfill and tamp the dirt. 8” diameter x 16” deep. 10 www.encloscreens.
ASSEMBLY INSTRUCTIONS ZP19047 STEP 6: FASTEN JOINER CLIPS STEP 6.1 Fasten the screens together with (2) Joiner Clips (J) using (4) 1” SelfDrilling Stainless Steel Screws (I). J Bottom Rail Top Rail I 90° application www.encloscreens.
ZP19047 ASSEMBLY INSTRUCTIONS STEP 7: INSTALL POST CAPS STEP 7.1 Push the Post Caps (A) down over the posts to lock into place. A 12 www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS ZP19047 VER.
