Specifications

ManualsBrandsEncore Manualscomputer componentsENLGA-1320

FCC Statement

This device compiles with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Warning! This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

CE-Mark Warning

In a domestic environment this product may cause radio

interference in which case the user may be required to take

adequate measures.

All Trademarks and trade names are the properties of their

respective owners.

Document Version: 2.0

Summary of content (9 pages)

PAGE 1
FCC Statement This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Warning! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
1. Introduction Thanks for the purchasing of your new Gigabit Ethernet PCI adapter. This document describes the Installation of network adapter. This adapter supports 10BASE-T, 100BASE-TX and 1000BASE-T Ethernet copper interface. Moreover, the PCI interface on the Gigabit Ethernet NIC complies with PCI Local Bus, is compatible with 32-bit PCI bus. As a bus master, the NIC requests access to the PCI bus, instead of waiting to be polled. 1.
PAGE 3
1.2 System Requirements To use the adapter, you need the following components: One 32 or 64 bit PCI master mode expansion slot that is compliant with PCI bus specifications One 3.5-inch, 1.44MB diskette drive The following cables: Port Type Media Max. Distance 10BASE-T Cat. 3, 4, or 5 UTP 100 meter 100/1000BASE-T Cat.
PAGE 4
3. Install the Adapter 1. 2. 3. 4. 5. 6. 7. 8. 9. Turn off the computer. Remove the computer’s cover, in accordance to its manual. Insert the contact edge of the adapter card into the connector of any available PCI Bus master expansion slot. Press the card firmly into the connector to PCI slot. Please make sure that the card’s contacts are fully seated in the PCI slot. Install the bracket screw that secures the card to the Computer chassis. Replace the computer’s cover.
PAGE 5
. Software Installation Microsoft Windows 98SE 1. 2. 3. 4. 5. 6. 7. 8. 9. Plug the adapter into the PCI slot. Press the power button on the case of PC to turn it on Windows 98 will prompt "PCI Ethernet Controller" in "Add New Hardware Wizard" dialog box, click button. Select "Search for the best driver for your device" from "Add New Hardware Wizard" dialog box, then click button. Insert driver disk bundled with "Gigabit Ethernet Network Adapter".
PAGE 6
4. 5. 6. 7. 8. 9. Click "Have Disk" for selecting one network adapter. Insert this driver disk in drive A, enter drive and pathname “A:\Winnt4”, then click the button. You will see that the "Gigabit Ethernet Network Adapter " string appears in the "Select OEM Option" dialog box, and click the button. Select the connection type in the "Gigabit Ethernet Network Adapter", and click . Follow the screen instructions and finish the rest of installation procedures. Restart your computer.
PAGE 7
5. 6. button. Windows XP will prompt "Gigabit Ethernet Network Adapter " in "Hardware Installation" dialog box, click button. Windows XP will display "The wizard has finished installing the software for Gigabit Ethernet Network Adapter/Fiber Gigabit Ethernet Network Adapter" in "Found New Hardware Wizard" dialog box, click to complete the installation. Linux kernel 2.2.x. 1. Compiling rtl8169.c "gcc -DMODULE -Wall -Wstrict-prototypes -O6 -c rtl8169.c". 2.
PAGE 8
3. 4. 5. "cp r8169.o /lib/modules//kernel/drivers/net" where represents the kernel version, say 2.4.18-3 in Red Hat 7.3 Insert module by "insmod r8169" Check driver status "dmesg" The media can be forced to one of the 5 modes as follows. Cmd: "insmod r8169 media = SET_MEDIA" For example: "insmod r8169 media = 0x04" will force PHY to operate in 100Mpbs Half-duplex. SET_MEDIA can be: _10_Half= 0x01 _10_Full = 0x02 _100_Half= 0x04 _100_Full= 0x08 _1000_Full= 0x10 Novell Netware System (4.
PAGE 9
Novell Netware System (5.X/6.X) 1. 2. Run NetWare Server System. When the Server prompt appears, load the NetWare Server Installation Utility ==> "LOAD NWCONFIG" 3. Select "Driver options" from the "Installation Options" menu. 4. Select "Configure network drivers" from the "Driver Options" menu. 5. Select "Select a driver" from the "Additional Driver Actions" menu. 6. Press to install an unlisted driver, and then press to specify a different path. 7.