ENRTR-514 Broadband Router User’s Manual
ENRTR-514 User’s Manual FCC Warning This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ENRTR-514 User’s Manual Contents: 1. Introduction ............................................................................................................... 4 1.1 Features........................................................................................................................ 4 1.2 Package Contents........................................................................................................ 5 1.3 LEDs Indication & Connectors of Broadband Router ................................
ENRTR-514 User’s Manual 3.8.2 Static Routing ................................................................................................ 35 3.8.3 Dynamic Routing ........................................................................................... 36 3.9 Misc............................................................................................................................. 36 3.9.1 UPnP ......................................................................................................
ENRTR-514 User’s Manual 1. Introduction Congratulations on purchasing ENRTR-514 Broadband Router. ENRTR-514 is a high quality and reliable Internet routing device, enables multiple users to share the Broadband Internet connection through a Cable or DSL modem. You can simply install ENRTR-514, connect to Cable/DSL modem, and surf Internet without extra efforts.
ENRTR-514 User’s Manual ● Internet Access Log: This feature is used to verify which Internet connections have been made. LAN Features ● 4-Port Ethernet Switch: The Broadband Router provides 4 10/100Base-T switching ports. ● Standard Compliance: The Broadband Router complies with the IEEE 802.3x full duplex flow control. ● DHCP Server Support: This feature provides a dynamic IP address to PCs and other devices upon request. The Broadband Router can act as a DHCP Server for devices on your local LAN.
ENRTR-514 User’s Manual 100Mbps 100Mbps Off WAN port is successfully connected to 10Mbps STATUS On (Steady Green) System is hung. Flashing ENRTR-514 is up and ready. LAN On (Steady Green) LAN port is successfully connected. (1, 2, 3, 4) Flashing Data is being sent or received.
ENRTR-514 User’s Manual 2. PC Configuration User needs to configure TCP/IP network settings, Internet access configuration for each system within the ENRTR-514 Broadband Router’s LAN network. By default, the Broadband Router acts as a DHCP server for server version of Windows, it automatically assigns IP address to each system when systems boot up. For all non-server versions of Windows, the default TCP/IP setting acts as a DHCP client.
ENRTR-514 User’s Manual b) Select the “Internet Protocol (TCP/IP)” for the network card on your system, then click “Properties”, window below will appear. ‧ If you decide to use IP address from the Broadband Router, select “Obtain an IP address automatically”. ‧ If you decide to use specific IP address, select “Use the following IP address”. Make sure enter correct addresses in “IP Address” and “Subnet Mask” fields. ‧ You must set the Broadband Router’s IP address as “Default Gateway”.
ENRTR-514 User’s Manual Checking TCP/IP Settings for Windows XP a) Click “Start”, select “Control Panel Network Connection” and right click “Local Area Connection” then select “Properties”, window below will appear.
ENRTR-514 User’s Manual b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear. ‧ If you decide to use IP address from the Broadband Router, select “Obtain an IP address automatically”. ‧ If you decide to use specific IP address, select “Use the following IP address”. Make sure enter correct addresses in “IP Address” and “Subnet Mask” fields. ‧ You must set the Broadband Router’s IP address as “Default Gateway”.
ENRTR-514 User’s Manual Checking TCP/IP Settings for Windows Vista a) Click “Start” “Control Panel “Manage Network Connections” and right click “Local Area Connection” then select “Properties”, window below will appear.
ENRTR-514 User’s Manual b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear. ‧ If you decide to use IP address from the Broadband Router, select “Obtain an IP address automatically”. ‧ If you decide to use specific IP address, select “Use the following IP address”. Make sure enter correct addresses in “IP Address” and “Subnet Mask” fields. ‧ You must set The Broadband Router’s IP address as “Default Gateway”.
ENRTR-514 User’s Manual 3. Setup Broadband Router Configurations via Web Browser The ENRTR-514 4Ports Broadband Router comes with a web-based configuration utility. Users can access this configuration utility from any of client system within the Broadband Router’s LAN. For best results, either use Microsoft Internet Explorer 6.0 or later.
ENRTR-514 User’s Manual 3.2 Quick Setup Quick Setup will help you setup the ENRTR-514 Broadband Router quickly. There are six types of WAN Connections: Dynamic IP Address, Static IP, PPPoE, PPTP, L2TP, and BigPond. When configure the Quick Setup wizard, you can setup Host Settings, such as Host name, Time Zone, and Daylight Saving as below. Click “Next” to continue.
ENRTR-514 User’s Manual 3.3 Administrator 3.3.1 Management Use this page to restrict management access based on a specific password. Passwords can contain from 4-12 alphanumeric characters, and are case sensitive. Idle Time-out - The amount of time of inactivity before the Broadband Router will automatically close the Administrator session. Set this to zero to disable it. Default is 300. Remote Management - By default, management access is only available to users on your local network.
ENRTR-514 User’s Manual 3.3.2 System Settings The System Settings window configures broadband router basic settings, such as router’s Host Name, Set Time Zone, Daylight Saving and Operation Mode. NTP Server (IP or Domain Name): Enter a Domain Name if it was provided by the ISP Time Zone: Select the time zone of the country you are currently in. The router will set its time based on your selection. Daylight Saving: The Broadband Router can also take Daylight savings into account.
ENRTR-514 User’s Manual 3.3.3 Firmware Upgrade User uses the Firmware Upgrade window to locate the new firmware then upgrade the system firmware. Click Browse… to search for the new firmware location, and then click OK to precede the upgrade. 3.3.4 Configuration Use this window to restore or backup broadband router settings, such as Restore Factory Default, Backup Settings and Restore Settings. The Factory Default settings are: “Username: admin”, “Password: admin”, “IP: 192.168.0.1”, “Netmask: 255.255.255.
ENRTR-514 User’s Manual 3.3.5 Tools If for any reason the device is not responding correctly, you may want to restart the unit by clicking on the Reboot button. 3.3.6 Language Specify the language of the device menu. The two languages are supported in this router: English and Traditional Chinese. 3.3.7 Log Settings Not only does the device display the logs of activities and events, it can be setup to send these logs to specific location by IP address.
ENRTR-514 User’s Manual 3.3.8 Logout Click Logout in the task bar to initiate broadband router logout process. 3.4 WAN Specify the WAN connection mode required by your Internet Service Provider, then click "OK" Button to provide detailed configuration parameters for the selected connection type.
ENRTR-514 User’s Manual (a) Dynamic IP address Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly. DHCP: Obtain an IP address automatically from the ISP. MAC Address Clone: You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with this MAC address.
ENRTR-514 User’s Manual Does ISP provide more IP address: If your ISP supports more IP addresses, please check it. Otherwise, leave it blank. (c) PPPoE PPP over Ethernet is a common connection method used for xDSL. User Name and Password: Enter the User Name and Password you use when logging onto your ISP through a PPPoE or PPTP connection. Service Name: Optional. Input the service name if your ISP requires it. Otherwise, leave it blank. Maximum Transmission Unit (MTU): Most ISP offers MTU value to users.
ENRTR-514 User’s Manual (d) PPTP PPP Tunneling protocol can support multi-protocol Virtual. PPTP: The Point-to-Point Tunneling Protocol (PPTP) is a method for implementing virtual private network. Server: Specify IP Address of the PPTP Server. IP Address and Subnet Mask: The private IP address and subnet mask would be assigned by your ISP. Connection ID: Optional. Input the connection ID if your ISP requires it. Otherwise, leave it blank.
ENRTR-514 User’s Manual (e) L2TP Layer 2 Tunneling protocol can support multi-protocol Virtual. L2TP Mode: The Layer two Tunneling Protocol (L2TP) is a method for implementing virtual private network. Server: Specify IP Address of the L2TP Server.
ENRTR-514 User’s Manual (f) BigPond BigPond is an Australian Internet service provider and is a subsidiary of Telstra. User Name: Enter the User Name is provided by your ISP. This field is case-sensitive. Password: Enter the Password is provided by your ISP. This field is case-sensitive. Server IP: Enter the authenticating server IP address or host name. MTU: The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 bytes. For some ISPs, you may need to modify the MTU.
ENRTR-514 User’s Manual 3.5 LAN 3.5.1 LAN Settings Configure the Gateway address of ENRTR-514 Broadband Router. To dynamically assign the IP address for client PCs, enable the DHCP Server, set the lease time, and then specify the address range. Valid IP addresses consist of four numbers, and are separated by periods. The first three fields are the network portion, and can be from 0-255, while the last field is the host portion and can be from 1-254.
ENRTR-514 User’s Manual 3.5.2 DHCP Client List The DHCP client list allows you to see which clients are connected to the Broadband Router via IP address, host name, and MAC address. You can select static to fix it. DHCP Client List: This page shows all DHCP clients (LAN PCs) currently connected to your network. The “DHCP Client List” displays the IP address and the MAC address and Remaining Time of each LAN Client. Use the Refresh button to update status.
ENRTR-514 User’s Manual 3.6 NAT 3.6.1 Virtual Server If you configure the Broadband Router as a virtual server, remote users accessing services such as Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP address. In other words, depending on the requested service (TCP/UDP port number), the Broadband Router redirects the external service request to the appropriate server. Enabled: Enable the Virtual Server option.
ENRTR-514 User’s Manual 3.6.2 Port Triggering Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications cannot work when Network Address Translation (NAT) is enabled.
ENRTR-514 User’s Manual 3.6.3 Port Mapping This functionality allows one or more public IP addresses to be shared by multiple internal users. Enter the Public IP address you wish to share into the Global IP field. Enter a range of internal IP that will share the global IP. Enabled: Enable the Port Mapping function. Comment: The description of this setting. Server IP: Enter the NAT server IP address. Mapping Ports: Enter the port address NAT server maps to.
ENRTR-514 User’s Manual 3.6.4 Passthrough Allow the Broadband Router correctly pass though the NAT gateway. [VPN] PPTP Passthrough: PPTP is a protocol that allows corporations to extend their own corporate network through private “tunnels” over the public Internet. Enable/Disable this protocol verification. IPSec Passthrough: IPSec is a framework for a set of protocols for security at the network or packet processing layer of network verification.
ENRTR-514 User’s Manual 3.6.5 DMZ If you have a client PC that cannot run Internet application properly from behind the NAT firewall or after configuring the Special Applications function, then you can open the client up to unrestricted two-way Internet access. Enter the IP address of a DMZ host to this screen. Adding a client to the DMZ (Demilitarized Zone) may expose your local network to a variety of security risks, so use this option only as the last resort. Enable: Enable/disable DMZ.
ENRTR-514 User’s Manual 3.7 Firewall 3.7.1 Firewall Options The ENRTR-514 Broadband Router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a demilitarized zone (DMZ).
ENRTR-514 User’s Manual 3.7.2 Client Filtering You can filter Internet access for local clients based on IP addresses, application types, (i.e., HTTP port), and time of day. For example, this screen shows that clients in the address range 192.168.2.50-99 are permanently restricted from using FTP (Port 21), while clients in the address range 192.168.2.110-119 are blocked from browsing the Internet from Monday through Friday.
ENRTR-514 User’s Manual 3.7.3 URL Filtering URL Filtering feature allowing you to prevent users from accessing specified websites on the basis of some policies. Default is “Disable URL Filter Function”. 3.7.4 MAC Filtering The MAC address filer let user to allow or block certain client PCs accessing the Internet based on MAC address. MAC Address Control: This function allows user to determine whether to filter out or accept the following MAC address connect to Internet.
ENRTR-514 User’s Manual 3.8 Routing 3.8.1 Routing Table The routing table displays the current routing information in system. 3.8.2 Static Routing A static route is a pre-determined pathway that network information must travel to reach a specific host or network. Destination LAN IP: The network address of destination LAN. Subnet Mask: The subnet mask of destination LAN. Gateway: The next stop gateway of the path toward the destination LAN.
ENRTR-514 User’s Manual 3.8.3 Dynamic Routing Dynamic Routing can be used to cache routers learned by routing protocols, thus allowing the automation of static routing maintenance. The router, using the RIP (Routing Information Protocol) protocol, determines the network packet’s route based on the fewest number of hops between the source and the destination. In the working mode, router stands for normal rip router. Default gateway stand for router announces defaults route on both sides. Default is Disable.
ENRTR-514 User’s Manual 3.9.2 DDNS DDNS (Dynamic DNS) provides you on the Internet with a method to tie their domain name to a computer or server. DDNS allows your domain name to follow your IP address automatically by having your DNS records changed when your IP address changes. 3.10 Status 3.10.1 Status This status page displays the router’s current status and configuration. All information is read-only.
ENRTR-514 User’s Manual 3.10.2 Log The log file keeps a running log of events and activities occurring on the device. You may want to save the log files by clicking on Log Setting. When the device is rebooted, the logs are automatically cleared.
