User manual

TERMS
4 digits 7 segment yellow LED display
( 2 ),( 3 ),( 4 ),( 5 ) Keypad
( 1 ) Digital display
DIMENSIONS
CONNECTION DIAGRAM
2
1
184-253V AC
50/60Hz 7VA
230V AC
Supply
Switch
Cable size: 1,5mm²
Fuse
F 100 mA
250V AC
Neutral
Line
SUPPLY :
NOTE :
Fuse should
be connected
1) Measurement value, measurement unit, the minimum or the maximum measured values are
displayed in the run mode.
Parameter name, parameter value or a user defined unit is displayed in the programming mode.
3) De
Used for making the minimum and the maximum measured values equal in the run mode.
crement or parameter selection key in the programming mode.
2) Increment or parameter selection key in the programming mode.
Used for displaying measurement unit or the max. measured value in the run mode.
4) Used for selecting run and programming modes, displaying
measurement unit or
adjusting parameters,
making the minimum and the maximum measured values equal.
9.1mm
Micro switch
Character height
ENDA EI141 is intended for installation in control panels. Make sure that the device is used only for intended purpose.
During an installation, all of the cables that are connected to the device must be free of energy. The device
must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. All
input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should not be
close to the power cables or components.
The shielding must be
grounded on the instrument side.
The installation and electrical connections must be carried on by a qualified staff and must be
according to the relevant locally applicable regulations.
1) Mains supply cords shall meet the requirements of IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the power supply switch shall bring the identification of the relevant instrument and it should be
easily accessible by the operator.
Note :
Holding screw
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
Panel cut-out
71mm
29mm
Panel
2
1
- Push up the flush-mounting
clamp in direction 1 as
shown in the figure above.
- Then, pull out the clamp in
direction 2.
For removing mounting clamps:
Rubber
packing
Flush mounting
clamp
Panel
Flush mounting
clamp
Note :
1) Panel thickness should be maximum 7 mm.
2) If there is no 60mm free space at the back
side of the device, it would be difficult to
remove it from the panel.
SN: XXXXXXXXX
1 2 3 4 5 6
7 8 9
10
11 12
EI141 PROGRAMMABLE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
230V AC +10% -20%
50/60Hz 7VA
INPUT
+
GND
SN: XXXXXXXXX
1 2 3 4 5 6
7 8 9
10
11 12
ENDA INDUSTRIAL ELECTRONICS
24V DC 10%
7VA
±
INPUT
+
GND
EI141-24DC PROGRAMMABLE INDICATOR
-
+
SN: XXXXXXXXX
1 2 3 4 5 6
7 8 9
10
11 12
EI141-24AC PROGRAMMABLE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
24V AC +10% -20%
50/60Hz 7VA
INPUT
+
GND
2./3 EI141-E
SETSET
EI141
ENDA
PROGRAMMABLE INDICATOR
SETSET
EI141
ENDA
PROGRAMMABLE INDICATOR
35mm
77mm
SN: XXXXXXXXX
EI141-230VAC
PROGRAMMABLE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
1 2 3 4 5 6
7 8 9
10
11 12
230V AC +10%-20%
50/60Hz 7VA
INPUT
+
GND
2
71mm
5mm