User manual

Measuring
type
Ifthiskeyispressed
measuringtype
appears.
,
*
SET
ACdC
yusingandkeysmeasuringtypecanbeadjusted , orB , to ac dc acdc.Threeleds
atthetopofthedisplayshowmeasuringtype.
SET
Ifkeyispressed,itreturnstoparametername.
Decimalpoint
position
yusingandkeysdecimalpoint canbeadjustedaccordingtovalueoftheB , state
c.t.r.r c.t.r.r 0.00 0.0
0.0 0 0
parameter.If parameterislowerthan10,measuredvaluecanbeshown ( )or( ), between10and100
measuredvaluecanbeshown ( )or( ) higherthan100measuredvaluecanbeshown ( ).
as Ifitis ,
as .Ifitis , as
Ifthiskeyispressed
decimalpoint
positionappears.
,
*
SET
Ifthiskeyispressed,
addressofthedeviceappears.
Adrs
1
Byusingandkeys,addressofthedevicecanbeadjustedbetween1-247.
SET
**
Optn
*
Ifthiskeyispressed,
samplingtimemeasurement
valueappears
SET
Samplingtime
measurementvalue
SET
Ifkeyispressed,itreturnstoparametername.
SET
Ifkeyispressed,itreturnstoparametername.
Samplingtimeofthemeasurementvalueisshownonthescreen.If selected;samplingtimeofthemeasurementis250ms,
If2isselected,itis500ms.If3isselected,itis750ms.If4isselected,itis1second.
1
SET
Ifkeyispressed,itreturnstoparametername.
Ifthiskeyispressed
currenttransforming
rateappears.
,
yusingandkeyscurrenttransformingratecanbeadjustedbetween
Ifthisparameterchangesupperlimitvalue setto scale, limitvalue setto scaleand
hysteresisvalues setto .
B ,
, is maximum minimum is minimum
are
5.00(/5)and
(/5).
0
9999
*
SET
SET
Ifkeyispressed,itreturnstoparametername.
Alarm
outputposition
Current
transforming
rate
Ifthiskeyispressed
alarmoutput
appears.
,
state
yusingandkeysalarmoutput canbeadjusted or If
atalarmcondition.
B , state to itisn.o. N.c no. adjust
outputrelayispowered
edto ,
SET
SET
Ifkeyispressed,itreturnstoparametername.
SET
baud
Byusingandkeys,baudratevalueofthedevicecanbeadjustedtoOFF,1200,2400,4800,9600,19200.
SET
Ifkeyispressed,itreturnstoparametername.
**
Whenthiskeyispressed,
baudrateisseen.
(*) Thereareonly
AdrS baud
parametersinthedevicesthosehavenorelay.
The and parametersareonlyinthedevicesthosehavemodbus.(**)
,, c.t.r.r tYPE d.Pnt optn, ,
Ifanykeyispressedin25secondsorthedeviceispowereddownandpoweredup,thenitreturnstooperationmode.
NOTE:
Ifkeyishelddownwhilethedeviceispoweredup, messagewillappearandfactorysettingswillberestored.d.PAr
Means,measuredcurrentvalueishigherthan scale.maximum
Means,measuredcurrentvalueislowerthan scale.minimum
ERRORMESSAGES
4
off
4./4EPA 41A-E2