Datasheet

ManualsBrandsENDA ManualsElectronic Control SystemsPID Temperature controller J, K, T, S, R, Pt100 -200 up to +1600 °C 2 A relay, SSR, Analogue current (L x W

J (Fe-CuNi) Thermocouple

K (NiCr-Ni) Thermocouple

T (Cu-CuNi) Thermocouple

S (Pt/0Rh-Pt) Thermocouple

R (Pt13Rh-Pt) Thermocouple

0-20 mA

4-20 mA

EN 60584

0... 600

0...1200

0... 400

0...1600

°C

+32... +1112

+32... +2192

+32... +752

+32... +2912

°F

Pt 100 Resistance Thermometer

EN 60751

-200...600

-99.9...300.0

-999...4000

°C

0,2% ( )of full scale

1 digit

0,2% ( )of full scale 1 digit

0,2% ( )of full scale

1 digit

0,2% ( )of full scale

1 digit

0,2% ( )of full scale 1 digit

-328... +1112

-99.9...+543.0

°F

°C

°F

OUTPUTS

Selectable as Control or Alarm2 output.Relay : 250V AC, 2A ( for resistive load), NO/NC.

Selectable as 0-20mA, 4-20mA analog output or logic control output(max. load 400 12V/20mAÙ)

(Alarm1 output).Relay : 250V AC, 2A ( for resistive load), NO/NC selectable.

AL1

ANL/SSR

Mechanical 30.000.000 operation; Electrical 300.000 operation

Life expectancy for relay

CONT./AL2

ENDA EUC442 PID UNIVERSAL CONTROLLER

* 48 x 48mm sized.

* Selectable sensor type.

* Selectable 0-20mA or 4-20mA input.

* Soft-Start.

Automatic calculation of PID parameters (SELF TUNE).

* Selectable Heat/Cool control.

* Communication vi RS-485 ModBus protocol (Optional).a

* Selectable 0-20mA or 4-20mA analog control output.

* Relay output can be programmable as second alarm or control output.

* AL1 relay output for first alarm out.

* Input offset feature.

* In the case of sensor failure relay state

can be selected.

periodical running or

Parameter access protection on 3 levels.

* Programming by using keypad or Modbus.

* CE marked according to European Norms.

ThankyouforchoosingENDA EUC442universalcontroller.

* Selectable analog, SSR or relay control output.

Readthisdocumentcarefullybeforeusingthisdevice. Theguaranteewillbeexpiredby

damagingofthedeviceifyoudon'tattendtothedirectionsintheusermanual. Alsowedon't

acceptanycompensationsforpersonalinjury,materialdamageorcapitaldisadvantages.

Enter PID parameters of the system if they are known at the beginning.

Otherwise, Self-Tune should be activated.

TECHNICAL SPECIFICATIONS

Input type Temperature range

Accuracy

ENVIRONMENTAL CONDITIONS

Height

Max. 2000m

80 up to 31 decreasing linearly 50 at 40 .% %

Ambient/storage temperature

Max. Relative humidity

0 ... +50 /°C -25... +70°C (with no icing)

°C °C

Rated pollution degree

According to EN 60529 Front panel : IP6

Rear panel : IP20

Do not use the device in locations subject to corrosive and flammable gases.

ELECTRICAL CHARACTERISTICS

Supply

230V AC +10% -20%, 50/60Hz or other power supply (please see page 5, order code)

Power consumption

Max. 5VA

2.5mm² screw-terminal connections

Wiring

Line resistance

Data retention

EMC

Safety requirements

EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B for standard EN 61000-4-3)

EEPROM (minimum 10 years)

EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)

For thermocouple max.100 , for 3 wired Pt 100 max. 20Ù Ù

CONTROL

Control type Single set-point and alarm control

On-Off / P, PI, PD, PID (selectable)

Control algorithm

A/D converter

15 bits

Sampling time

Proportional band

Derivative time

Integral time

Control period

Hysteresis

Output power

500ms

Adjustable between 0 and 100 . If , On-Off control is selected.Pb 0=% % %

Adjustable between 0.0 and 100.0 minutes

Adjustable between 0.00 and 25.00 minutes

and 250 secondsAdjustable between 1

1 and 50Adjustable between °C/F

The ratio of power at a set point can be adjusted between 0 and 100% %

HOUSING

Housing type

Suitable for flush-panel mounting according to DIN 43 700.

Dimensions

W48xH48xD87mm

Weight

Approx. 250g (after packing)

Self extinguishing plastics.

Enclosure material

While cleaning the device, solvents (thinner, benzine, acid etc.) or must not be used.corrosive materials

uptodate:01022014,modificationreservedandcanbechangeanytimepreviousnotice!

english

RoHS

conform

1./5EUC442-E

UNIVERSAL CONTROLLER

ENDA

CSET

ASET

SET

EUC 442

CNT/AL2

AL1

SRAN/S

Summary of content (5 pages)

PAGE 1
english Read this document carefully before using this device. The guarantee will be expired by damaging of the device if you don't attend to the directions in the user manual. Also we don't accept any compensations for personal injury, material damage or capital disadvantages. ENDA EUC442 PID UNIVERSAL CONTROLLER Thank you for choosing ENDA EUC442 universal controller. * 48 x 48mm sized. * Selectable sensor type. * Selectable 0-20mA or 4-20mA input. * Automatic calculation of PID parameters (SELF TUNE).
PAGE 2
SET SET If CSET key is pressed while holding ASET ASET key, the programming mode is enabled. CSET Con.o. ASET ASET Pb 4 Pb = Proportional band. Adjustable between 0% and 100% Setting Pb = 0% On-Off control is selected. A1.Hy. 2 tý 4.0 Ti = Integral time. A1.tp. ýndE. Adjustable between 0.0 and 100.0 minutes. If ti = 0.0, integral effect is not used. Setting Pb = 0 this parameter is not seen. td = Derivative time. Adjustable between 0.00 and 25.00 minutes. If td = 0.
PAGE 3
Entering from the programming mode to the run mode: If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered. SET SET Alternatively, the same function occurs first pressing key and then pressing ASET Page 2/5 S.tun. ASET ASET Before starting sef-tune procedure, be sure A.tun parameter is YES in the SECU menu. ConF. Page 2/5 U.sC.H. 3000 d.pnt. 0 d.adr. 1 baud 9600 S.Str. run ASET SECU. ASET U.sC.l. -999 CSET keys together.
PAGE 4
TERMS EUC 442 CNT/AL2 AN/SSR (7) ( 1 ) Process value during normal operation Mnemonic parameter code during programming PV ( 2 ) Set point during normal operation. AL1 Data value during programming SV ( 3 ) Increment key during normal operation and programming Parameter selection key during programming ( 4 ) Decrement key during normal operation SET CSET If only this key is pressed in normal operation, software version number is seen.
PAGE 5
Depth DIMENSIONS 87mm 1 For removing the device from the panel: - While pressing both side of the device in direction 1, push it in direction 2. EUC 442 CNT/AL2 48mm 58mm AN/SSR PV AL1 SV SET CSET ASET ENDA UNIVERSAL CONTROLLER 2 1 Connection cables Panel cut-out 51mm +0.6 mm 45 +0.6 mm 45 80mm Flush mounting clamp Panel Note 1) While panel mounting, additional distance required for connection cables should be considered. 2) Panel thickness should be maximum 9mm.