Owner`s manual

Outdoor Patio Heater Model No. 233000
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
page no.
7
Installing LP Gas Tank
To operate you will need (1) precision-filled standard grill LP gas
tank (20 lbs.) with external valve threads.
Note: An empty standard grill LP gas tank weighs approximately
18 lbs. A precision-filled standard grill LP gas tank should weigh
no more than 38 lbs.
Caution: LP gas tank must be properly
disconnected and removed prior to moving this
heater.
Insert LP Gas Tank
Place precision filled LP gas tank upright into hole in patio heater so it is arranged for vapor
withdrawal.
Secure LP Gas Tank
Secure tank in place by attaching loose end of tank restraint chain to hole in right leg.
Connect LP Gas Tank
Before connecting, be sure that there is no debris caught in
the head of the LP gas tank, head of the regulator valve or
in the head of the burner and burner ports.
Connect gas line to tank by turning knob clockwise until it
stops.
Disconnect LP Gas Tank
Before disconnecting make sure the LP gas tank valve is
“CLOSED”.
Disconnect gas line from LP gas tank by turning knob
counterclockwise until it is loose.
Caution: LP gas tank must be properly
disconnected and removed prior to moving
this heater.
Need a tank of gas? Try tank exchange service. It’s easy, fast,
safe, and available at tens of thousands of conveniently located
retail outlets nationwide. You can purchase a new full tank or
exchange your empty for a precision filled one.
Checking for Leaks
Burner Connections
1. Make sure the regulator valve and hose connections are securely fastened to the burner and
the tank.
2. If your unit was assembled for you, visually check the connection between the burner pipe
and orifice. Make sure the burner pipe fits over the orifice.
WARNING: Failure to inspect this connection or follow these
instructions could cause a fire or an explosion which can cause death,
serious bodily injury, or damage to property.
3. If the burner pipe does not rest flush to the orifice,
please contact 1.800.762.1142 for assistance.
Tank/Gas Line Connection
1. Make 2-3 oz. of leak solution by mixing one part liquid
dishwashing soap with three parts water.
2. Make sure control knob is in “OFF” position. (Figure 3)
3. Turn LP gas tank valve to “OPEN”.
4. Spoon leak check solution at all “X” locations.
(Figures 1 and 2)
a. If any bubbles appear turn LP gas tank valve to
“CLOSED”, reconnect and re-test.
b. If you continue to see bubbles after several
attempts, turn LP gas tank valve to “CLOSED”,
disconnect LP gas tank and contact
1.800.762.1142 for assistance.
b. If no bubbles appear after one minute turn LP gas
tank valve to “CLOSED”, wipe away solution and
proceed.
Before Lighting
1. Heater should be thoroughly inspected before each use,
and by a qualified service person at least annually.
2. If relighting a hot heater, always wait at least
5 minutes.
3. Inspect the hose assembly for evidence of excessive
abrasion, cuts or wear. Suspected areas should be
leak tested. If the hose leaks, it must be replaced prior
to operation. Only use the replacement hose assembly
specified by manufacturer.
Lighting
Note: This heater is equipped with a pilot light that allows
for safer startups and shutdowns. Pilot must be lit before
main burner can be started.
1. Control knob must be in the “OFF” position. (Figure 3)
2. Turn LP gas tank valve to “OPEN”.
3. Open viewing hole by sliding cover to either side.
(Figure 6)
4. Push control knob in and rotate to “PILOT” position.
(Figure 4)
Note: For initial start or after any tank change, hold control
knob in for 2 minutes to purge air from gas lines before
proceeding.
5. Push-button Ignition: Immediately push igniter button
a couple of times. Pilot light flame will appear and be
visible through viewing hole.
Electronic Ignition: Immediately push igniter button for
five (5) seconds. Pilot light flame will appear and be
visible through viewing hole.
6. Release control knob after 30 seconds. Pilot light will
remain lit.
7. If ignition does not occur, turn control knob “OFF”, wait 5
minutes and repeat lighting procedure.
8. Turn control knob to “HIGH”. (Figure 5) Main burner will
light immediately. Flame is visible through viewing hole.
If not, turn control knob “OFF”, wait 5 minutes, and
repeat lighting procedure.
9. If for some reason your ignitor fails to deliver a spark,
your heater can be started by inserting a lit match
through the pilot view hole while pushing the control
knob in while in the “PILOT” position.
WARNING: Be careful when attempting to
manually ignite this heater. Holding in the
control knob for more than 10 seconds
before igniting the gas will cause a ball of
flame upon ignition.
Have a question or are having problems visit
www.bluerhino.com or call 1.800.762.1142.
Figure 1
X
Figure 2
Figure 3
PILOT / PILOTO
push in / presione y
mantenga presionado
LOW /
BAJO
HIGH /
ALTO
OFF /
APAGADO
Figure 4
PILOT / PILOTO
push in / presione y
mantenga presionado
LOW /
BAJO
HIGH /
ALTO
OFF /
APAGADO
Figure 5
PILOT / PILOTO
push in / presione y
mantenga presionado
LOW /
BAJO
HIGH /
ALTO
OFF /
APAGADO
Figure 6
View Hole
Operating Instructions