Installation Manual

ManualsBrandsEndless Summer ManualsFireplacesEndless Summer WAD997SP GAD1401M LP Gas Outdoor Fireplace, Brown

INSTALLATION INSTRUCTIONS

AltRider Lower Crash Bars

for Honda Africa Twin CRF1000L

Dear Rider,

Thank you for choosing AltRider! Whether a seasoned world adventurer or a

first time ADV-Newbie, we welcome you to the AltRider experience. You can

install your new product with the utmost confidence. AltRider designs, tests,

and manufactures all of its products here in the United States. We are

proud to do what we do, and honored to present to you the product of our

labors.

Enjoy it, show it off, and most of all, RIDE IT!

Venture On,

Jeremy LeBreton

AltRider LLC

mailing: 4000 Aurora Ave N Ste 100

Seattle, WA 98103 USA

phone: 206-922-3618

email: info@altrider.com

web: www.altrider.com

Global

Europe

mailing: AltRider EU

Heliumstraat 230

2718 RS Zoetermeer

The Netherlands

email: info@altrider.eu

AltRider Lower Crash Bars

Honda Africa Twin CRF1000L

Package Contents:

- Crash Bars

- Hardware Kit

- Instructions

MADE IN THE USA

The most up to date instructions can be downloaded from the product page at altrider.com, under the instructions tab.

made in

USA

REV 14.3

Summary of content (6 pages)

PAGE 1
made in USA AltRider Lower Crash Bars for Honda Africa Twin CRF1000L INSTALLATION INSTRUCTIONS The most up to date instructions can be downloaded from the product page at altrider.com, under the instructions tab. Dear Rider, Thank you for choosing AltRider! Whether a seasoned world adventurer or a first time ADV-Newbie, we welcome you to the AltRider experience. You can install your new product with the utmost confidence.
PAGE 2
1 Honda Africa Twin // Low Crash Bars // Installation Instructions Kit: 1 1 Left bar 2 Right bar 3 Right rear bracket 2 8 4 (qty 2) M10 x 25 socket cap screw 5 (qty 3) M10 washer 6 M10 x 85 x 1.
PAGE 3
2 Honda Africa Twin // Low Crash Bars // Installation Instructions Install the Bracket Set AT16-9-1000 before installing either the lower or upper crash bars. 1 Depress locking tabs and unfasten the small clip that holds the oxygen sensor wire to the fill reservoir (located near the rear brake pedal). 2 Use 12mm socket with extension, loosen the four (4) acorn nuts that hold the exhaust header flanges. Do not remove completely, but make very loose.
PAGE 4
3 Honda Africa Twin // Low Crash Bars // Installation Instructions 5 Use 14mm spanners to loosen both frame rail M10 screws and nuts. 6 A 7 Remove both screws. discard the forward, shorter (60mm) screw, but keep the nut. !!TIP If removing the screws is difficult, wrap a screwdriver or small pry bar with cloth and lever the frame rail downward to release the pressure on the screw. B Install the Right Rear bracket.
PAGE 5
4 Honda Africa Twin // Low Crash Bars // Installation Instructions A B 9 Remove two (2) M8 hex cap screws from the left rear frame rail. (If AltRider skid plate bracket is alread installed, leave it in place). 10 Install Left bar. Add a drop of thread locker to each screw before installation. (A) Use two M8 x 25 socket cap screws at the front (supplied with Bracket Set kit). (B) Use two M8 x 25 hex cap screws at the rear (supplied with Crash Bar kit). Tighten all M8 screws to 23Nm.
PAGE 6
5 Honda Africa Twin // Low Crash Bars // Installation Instructions CONGRATULATIONS! You’ve completed your installation. If at any point you have questions about your installation or have any feed back for us, we’d love to hear it. A downloadable version of these instructions can be found at our web site. www.AltRider.com After 5 hours of riding, or 100 miles, check all the fasteners on the assembly to ensure they are tightened to spec. Global Office: email: info@AltRider.