Product Info

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRAFTDRAFT DRAFT DRAFT
Micropilot FMR51, FMR52
Endress+Hauser V. 10, Rev. 3, 1-10-2019 97
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
[Any] changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at least 4,5 cm separation from the human body at all
times.
Afin de se conformer aux exigences d'exposition RF FCC / ISED, cet appareil doit être installé pour fournir au moins 4,5 cm de séparation du corps humain en
tout temps
• The installation of the LPR/TLPR device shall be done by trained installers, in strict compliance
with the manufacturer’s instructions.
• The use of this device is on a “no-interference, no-protection” basis. That is, the user shall accept
operations of high-powered radar in the same frequency band which may interfere with or
damage this device. However, devices found to interfere with primary licensing operations will be
required to be removed at the user’s expense.
• This device shall be installed and operated in a completely enclosed container to prevent RF
emissions, which can otherwise interfere with aeronautical navigation.
• The installer/user of this device shall ensure that it is at least 10 km from the Dominion
Astrophysical Radio Observatory (DRAO) near Penticton, British Columbia. The coordinates of the
DRAO are latitude 49°19ʹ15ʹʹ N and longitude 119°37ʹ12ʹʹ W. For devices not meeting this
10 km
separation (e.g., those in the Okanagan Valley, British Columbia,) the installer/user must
coordinate with, and obtain the written concurrence of, the Director of the DRAO before the
equipment can be installed or operated. The Director of the DRAO may be contacted at
250-497-2300 (tel.) or 250-497-2355 (fax). (Alternatively, the Manager, Regulatory Standards
Industry Canada, may be contacted.)
• The FMR51T is a submodel of the FMR51 that fulfills the requirements for use as TLPR
(Tank Level Probe Radar).
• The model FMR51L is a submodel of the FMR51. "L" indicates the unique option BD of the
feature 070 ("Antenna") that fullfills the requirements for use as LPR (Level Probe Radar).
• The FMR52T is a submodel of the FMR52 that fulfills the requirements for use as TLPR
(Tank Level Probe Radar).
• The model FMR52L is a submodel of the FMR52. "L" indicates the unique option BP of the
feature 070 ("Antenna") that fullfills the requirements for use as LPR (Level Probe Radar).
Japanese radio approval
The devices comply with Japanese Radio Law, Article 6
, Section 1(1)
CRN approval
Some device versions have a CRN approval. Devices are CRN approved if the folowing two conditions
are met:
•
The device has a CSA approval (Product structure: Feature 010 "Approval")
•
The device has a CRN approved process connection according to the following table.
Feature 100 of the product structure Process connection
AFJ NPS 2" Cl.150 RF, 316/316L
AFK NPS 2" Cl.150, PTFE >316/316L
AFM NPS 2" Cl.150, AlloyC >316/316L
AGJ NPS 3" Cl.150 RF, 316/316L
AGK NPS 3" Cl.150, PTFE >316/316L
AGM NPS 3" Cl.150, AlloyC >316/316L
AHJ NPS 4" Cl.150 RF, 316/316L
AHK NPS 4" Cl.150, PTFE >316/316L
AHM NPS 4" Cl.150, AlloyC >316/316L
AJJ NPS 6" Cl.150 RF, 316/316L
AJK NPS 6" Cl.150, PTFE >316/316L
AJM NPS 6" Cl.150, AlloyC >316/316L
ARJ NPS 2" Cl.300 RF, 316/316L