Installation Instructions

ManualsBrandsEndress and Hauser SE ManualsElectronicsFieldPort SWA50

Table Of Contents

Application

The FieldPort SWA50 converts the HART signal of the

connected HART field device to a reliable and encrypted

Bluetooth® or WirelessHART signal. The FieldPort SWA50 can

be retrofitted to all 2-wire and 4-wire HART field devices in

both hazardous and non-hazardous areas. The robust stainless

steel housing allows the FieldPort SWA50 to be installed even

in harsh industrial environments.

The combination of the Bluetooth® version of the SWA50 with

a FieldEdge SGC200 delivers fast and easy connection to the

Netilion Cloud.

The WirelessHART version of the SWA50 can be easily

integrated into any WirelessHART network.

Your benefits

• Reliable transmission of the measured process values

through the connected FieldPort SWA50 via encrypted

Bluetooth® or WirelessHART communication

• Easy to retrofit all 2-wire or 4-wire HART field devices

• Easy connection of all HART field devices to the

Netilion Cloud

• Loop-powered adapter, without affecting the process signal

• Easily accessible, wireless, onsite diagnostic information of

connected HART field device

Products Solutions Services

Technical Information

FieldPort SWA50

Intelligent Bluetooth® and/or WirelessHART adapter for

all HART field devices

TI01468S/04/EN/01.19

unbekannt

2019-09-30

Summary of content (20 pages)

PAGE 1
TI01468S/04/EN/01.19 unbekannt 2019-09-30 Products Solutions Services Technical Information FieldPort SWA50 Intelligent Bluetooth® and/or WirelessHART adapter for all HART field devices Application The FieldPort SWA50 converts the HART signal of the connected HART field device to a reliable and encrypted Bluetooth® or WirelessHART signal. The FieldPort SWA50 can be retrofitted to all 2-wire and 4-wire HART field devices in both hazardous and non-hazardous areas.
PAGE 2
FieldPort SWA50 Table of contents About this document . . . . . . . . . . . . . . . . . . . . . . . . 3 Radio approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Function and system design . . . . . . . . . . . . . . . . . . . 3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . . . 15 Function . . . . . . .
PAGE 3
FieldPort SWA50 About this document Symbols Safety symbols DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious or fatal injury. WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious or fatal injury. CAUTION This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor or medium injury.
PAGE 4
FieldPort SWA50 NOTICE Safety applications with control functions via Bluetooth signal or WirelessHART signal Undesirable behavior of safety application ‣ Do not use a wireless signal such as Bluetooth or WirelessHART in a safety application with a control function.
PAGE 5
FieldPort SWA50 System architecture of SWA50 WirelessHART version 1 2 3 4 7 5 6 8 6 9 10 1 Netilion 15 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 14 13 12 11 System architecture of SWA50 WirelessHART version Endress+Hauser Field Xpert, e.g. SMT7x Host application / FieldCare SFE500 Ethernet communication WirelessHART-Fieldgate, e.g.
PAGE 6
FieldPort SWA50 WirelessHART • WirelessHART communication interface (IEC 62591) • HART version 7.5, backward-compatible with previous HART versions Transmission frequency band 2.4 GHz (ISM band) The range depends on the alignment of the FieldPort SWA50, the mounting location and the environmental conditions.
PAGE 7
FieldPort SWA50 Power supply Electrical connection 2-wire HART field device with passive current output Some grounding concepts require a shielded cable. If connecting the cable shield to the FieldPort SWA50, you must use an EMC cable gland. See ordering information, feature 060, option B.
PAGE 8
FieldPort SWA50 + + + IN+ OUT+ + – – – IN– OUT– – 2 1 4 3 A0040492 6 1 2 3 4 Electrical connection for 4-wire HART field devices with active current output (optional grounding not shown) Supply voltage for 4-wire HART field device 4-wire field device with active 4 to 20 mA-HART output Electronic insert SWA50 PLC or transmitter with passive current input (optional), alternatively wire bridge between terminals OUT+ and OUT– You must connect a PLC, a transmitter or a wire bridge to termina
PAGE 9
FieldPort SWA50 Application Input terminal IN Output terminal OUT 2-wire HART field device →  4,  7 Cable from supply voltage, PLC with active current output or transmitter with active current output Cable to 2-wire HART field device 4-wire HART field device with passive current output →  5,  7 Cable from supply voltage, PLC with active current output or transmitter with active current output Cable to 4-wire HART field device 4-wire HART field device with active current output →  6,  8 Cabl
PAGE 10
FieldPort SWA50 Voltage drop • If internal HART communication resistor is deactivated • 3.2 V in operation • < 3.8 V at start-up • If internal HART communication resistor is activated (270 Ohm) • < 4.2 V at 3.6 mA loop current • < 9.3 V at 22.5 mA loop current To select the supply voltage, pay attention to the voltage drop via the FieldPort SWA50. The remaining voltage must be high enough to enable the start-up and operation of the HART field device. Power consumption Max. 0.
PAGE 11
FieldPort SWA50 1 2 3 A0043240  10 1 2 3 Example of remote mounting FieldPort SWA50 "remote mounting" version Cable HART field device 1 2 3 A0043241  11 1 2 3 Mounting instructions Example of direct mounting Cable FieldPort SWA50 "direct mounting" version HART field device • Pay attention to range. →  6 • Observe a distance of at least 6 cm from walls and pipes. Pay attention to the expansion of the Fresnel zone. • Avoid mounting in close proximity to high-voltage devices.
PAGE 12
FieldPort SWA50 Environment Ambient temperature range • –40 to +85 °C (–40 to +185 °F) • Ex version for temperature class T4: –40 to +70 °C (–40 to +158 °F) Storage temperature range –40 to +85 °C (–40 to +185 °F) Climate class As per IEC 60068-2-38 test Z/AD Degree of protection When housing is closed, tested according to: • IP68 / NEMA 6P (24 h at 1 m under water) • IP66 / NEMA 4X Vibration resistance As per IEC 60068-2-64:2008 • a(RMS) = 50 m/s² • f = 5 to 2000 Hz • t = 3 planes x 2 h Vibration
PAGE 13
FieldPort SWA50 "Direct mounting" version 3 Ø 39.9 (1.57) 2 33.6 (1.32) Ø 41.9 (1.65) 1 79.5 (3.13) Ø 15 (0.59) 113.1 (4.45) SW 36 (36 AF) SW 24 (24 AF) 132.1 (5.20) A0040483  13 Connection adapter with M20 thread Transmission window M20 cable gland 1 3 Ø 39 (1.54) 2 33.6 (1.32) Ø 42 (1.65) 1 2 3 Dimensions of "direct mounting with M20" version in mm (in) 79.5 (3.13) 113.1 (4.45) SW 36 (36 AF) SW 24 (24 AF) 146 (5.
PAGE 14
FieldPort SWA50 Cable entries • Standard: plastic • EMC version: brass Connection adapter • M20 thread: stainless steel. 1.4404 (316L) • NPT 1/2" thread: stainless steel. 1.
PAGE 15
FieldPort SWA50 Ordering information Detailed information on the product structure are available as follows: • On the Endress+Hauser website: www.endress.com → Enter "SWA50" in the search field → Click the icon to the right → Product Configurator opens → Configure product • From your Endress+Hauser Sales Center: www.addresses.endress.
PAGE 16
FieldPort SWA50 1 2 A0043411  16 1 2 Alignment options via support bracket Various mounting positions on support bracket By rotating the support bracket Dimensions 165 (6.50) 87 (3.43) Ø 65 (Ø 2.56) 52 (2.05) 81 (3.
PAGE 17
40 (1.75) 28 (1.10) 18 (0.71) FieldPort SWA50 4.75 (0.19) 18 (0.71) 33 (1.30) 78 (3.07) 103 (4.06) A0043410  18 Dimensions of retaining bracket – wall mounting Supplementary documentation Standard documentation SWA50 Operating Instructions • Bluetooth: BA01987S • WirelessHART: BA02046S Brief Operating Instructions WirelessHART: KA01436S Supplementary devicedependent documentation for SWA50 All explosion-protection data are provided in separate Ex documentation.
PAGE 18
FieldPort SWA50 Standard documentation for SWG70 Technical Information TI00027S Operating Instructions BA00064S Registered trademarks Bluetooth® Registered trademark of the Bluetooth Special Interest Group (SIG), Kirkland, Washington, USA HART® Registered trademark of the FieldComm Group, Austin, Texas, USA WirelessHART ® Registered trademark of the FieldComm Group, Austin, Texas, USA Radio approvals Europe This device meets the requirements of the "Radio Equipment Directive" (RED) 2014/53/EU: • EN 300
PAGE 19
FieldPort SWA50 Changes or modifications made to this device that are not expressly approved by Endress+Hauser may void the FCC authorization to operate this device. This device must be installed to ensure a minimum antenna separation distance of 20 cm from all persons. Français Le présent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de licence.
PAGE 20
www.addresses.endress.