- HeatStar by Enerco Gas Heater User Manual

ManualsBrandsEnerco ManualsGas HeaterHSVFB10LP

Mr. Heater, INC., 4560 W. 160

ST., CLEVELAND, OHIO 44135 · 216-916-3000

WARNING: If the information in this manual is not followed exactly, a ﬁre or explosion may result causing

property damage, personal injury, or loss of life.

- Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Shut off gas supply

• Do not try to light any appliance

• Do not touch an electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

- Installation and service must be performed by a qualiﬁed installer, service agency, or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air must be provided. Refer to Fresh Air for Combustion and

Ventilation section on page 4 of this manual.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage. Refer to this manual for correct installation and operational procedures. For assistance or additional

information consult a qualiﬁed installer, service agency, or gas supplier.

70810 Rev. B 05/10

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place

instructions in a safe place for future reference. Do not allow anyone who has not

read these instructions to assemble, light, adjust or operate the heater.

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

MODEL

HSVFR10LPT

HSVFB10LPT

Blue Flame Heaters

MHVFB10LP

HSVFB10LP

TSVFB10LP

Plaque Heaters

MHVFR10LP

HSVFR10LP

TSVFR10LP

For model serial numbers,

see page E16.

Summary of content (16 pages)

PAGE 1
Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference. INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL MODEL HSVFR10LPT HSVFB10LPT READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater. For model serial numbers, see page E16.
PAGE 2
This appliance may be installed in an aftermarket* permanently manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with any other gas. *Aftermarket completion of sale, not for the purpose of resale, from the manufacturer. WARNINGS • IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater.
PAGE 3
SPECIFICATIONS IR10 LP BF10LP BTU (Available) 10,000 10,000 Type of Gas LP-Gas Only LP-Gas Only Ignition Piezo Piezo Pressure Regulator Setting 10 Inches of Water 10 Inches of Water Inlet Gas Pressure (Maximum) 14 Inches of Water 14 Inches of Water Inlet Gas Pressure (Minimum) 11 Inches of Water 11 Inches of Water Burners / Orifice nozzles 2 1 Thermostatic Control No No Clearances: inches (mm) Top 36” (915cm) 36” (915cm) Sides 6” (152cm) 6”
PAGE 4
SAFETY DEVICE b. Whether stripping has been added on openable windows and doors, and c. Caulking or sealants are applied to areas such as joints around windows and door frames, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical, and gas lines, and at other openings. If you home does not meet all of the three criteria above, see Determing the Type of Heater Location Space, below. This heater has a pilot with an Oxygen Depletion Sensor (ODS) safety shut off system.
PAGE 5
heater, Gas furnace, Vented gas heater, Gas fireplace logs, and Other gas appliances* *Do not include direct-vent gas appliances. Directvent draws combustion air from the outdoors and vents to the outdoors. Example: Gas water heater 40,000 Btu/hr Vent Free Heater + 20,000 Btu/hr Total =60,000 Btu/hr 4. Compare the maximum Btu/hr the space can support with the actual amount of Btu/hr used.
PAGE 6
WARNING: A qualified service person must install heater. Follow all local codes. For convenience and efficiency, install the heater: • CHECK GAS TYPE Use only LP-gas. If your gas supply is not LP-gas, do not install heater. Call dealer where you bought heater for proper type heater. • In the coldest part of the room.
PAGE 7
1. Attach to wall studs 2. Attach to wall anchor 3. Insert mounting screws through bracket and into wall studs. 4. Tighten screws until mounting bracket is firmly fastened to wall studs. Attaching to Wall using Anchor: For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry) Note: Wall anchors, mounting screws, and spacer are in hardware package. The hardware package is provided with heater. 1. Drill holes at marked locations using 5/16” drill bit.
PAGE 8
Screw hole location, heater may be locked into position using anchoring holes in mounting feet. Note: Use of floor mounting feet will require you to use a 3/8 NPT street elbow to make gas connection. Screw hole Figure 10 CONNECTING TO GAS SUPPLY 2. Mark screws locations on wall. 3. Remove heater from mounting bracket. 4. If installing bottom mounting screw into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching to Wall using Anchor.
PAGE 9
1. Close equipment shutoff valve (see figure 13). 2. Pressurize supply piping system by either using compressed air or opening propne/LP supply valve. 3. Check all joints from the propane/LP supply valve to equipment shutoff valve (see figure 14). Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak. 4. Correct all leaks at once. 5. Depressurize and relieve pressure from supply piping system.
PAGE 10
8. Turn off heater (see To Turn OFF Gas to Appliance, page 10. 9. Replace lower front panel. be depressed for about 30 seconds. This will allow air to bleed from the gas system. 6. Push in control knob and rotate control knob back to OFF position then rotate counterclockwise to PILOT/IGN position. This will light pilot. If needed gently keep rotating control knob back and forth while depressed until pilot lights. 7. Keep control knob depressed in for ten (10) seconds after lighting pilot.
PAGE 11
2. Turn control knob clockwise to the OFF position. SHUTTING OFF BURNER ONLY (PILOT STAYS LIT) 1. Turn control knob clockwise to the PILOT/IGN position. INSPECTING BURNER Check pilot flame pattern and burner flame pattern often. Note: Your heater may have either pilot assembly. Figure 17 PILOT FLAME PATTERN Figure 21 show a correct pilot flame pattern. Figure 22 shows an incorrect pilot flame pattern. The incorrect pilot flame pattern is not touching thermocouple.
PAGE 12
TROUBLESHOOTING NOTE: All troubleshooting items are listed in order of operation and likely occurrence. WARNING: Only a qualified service person should service and repair heater. CAUTION: Never use a wire needle, or similar object to clean ODS/pilot. This can damage ODS/pilot unit. Make sure grille guard is in place before running heater. If screen or grille guard is removed for servicing it must be replaced prior to operating the heater.
PAGE 13
OBSERVED SYMPTOM POSSIBLE CAUSE REMEDY Heater shuts off in use (ODS operates) 1. Not enough fresh air is available 2. Low line pressure 3. ODS/pilot is partially clogged 1. Open window and/or door for ventilation 2. Contact local gas company 3. Clean ODS/pilot (see Cleaning and Maintenance, page 11) Gas odor even when control knob is in OFF position 1. Gas leak. See WARNING statement at top of page 2. Control valve is defective 1.
PAGE 14
UNVENTED LP-GAS FIRED ROOM HEATER • Model #IR10LP/ BF10LP Model #BF10LP 1-1 28 3 1-4 5 1-3 15 10 14 6 8 7 19 20 1-2 21 2 23 13 17 22 4 30 12 16 28 1-1 Model #IR10LP 5 1-3 3 10 6 7 19 23 1-4 26 8 21 24 27 1-2 29 2 13 18 16 11 9 Unvented Liquid Propane Fired Room Heater 22 25 30 14 Installation Instructions and Owner’s Manual
PAGE 15
IR10LP and BF10LP • PARTS LIST This list contains replacement parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 16 of this manual. ITEM PART NO. DESCRIPTION QTY.
PAGE 16
INSTALLATION Instructions and Owner’s Manual READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater. WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY.