DC2DC POWER PRODUCTS
DC2DC POWER PRODUCTS 12V & 24V VSR Relays Page 3 EN-VSR1224-100 EN-VSR1224-160 Programmable Low Battery Cut-Outs Page 4 EN-LBC1224-10 EN-LBC1224-40 EN-LBC1224-60 EN-LBC1224-200 Charging Diode Splitters Page 5 EN-BI-160-2 EN-BI-160-3 DC to DC Converters with Galvanic Isolation EN-DC1212-15G EN-DC1212-25G EN-DC1224-7.5G EN-DC1224-12G EN-DC1224-12.5G EN-DC2412-15G EN-DC2412-25G EN-DC2424-7.5G EN-DC2424-12.5G EN-DC4812-15G EN-DC4812-25G EN-DC4824-12.5G EN-DC4848-3.2G EN-DC4848-6.
DC2DC POWER PRODUCTS 12V & 24V VSR Relays The Enerdrive ePOWER VSR Battery Separator is an Essential Part of Your Dual Battery System. The ePOWER VSR or voltage sensitive relay is essential for systems that utilises more than one battery. When the engine is started, starting & auxiliary batteries are separated allowing only the starting battery to be charged. When the charge voltage reaches 13.2 Volts the VSR engages allowing both starting and auxiliary batteries to be charged.
DC2DC POWER PRODUCTS Programmable Low Battery Cut-Outs The Enerdrive ePOWER Low Battery Cutoff Switch Protects Your Batteries Without The Use Of A Relay. The ePOWER Low Battery Cutoff protects your batteries from non essential loads before the battery is completely discharged causing damage to batteries and potently denying your engine cranking power. These Low Battery Cutoffs also protect connected electrical appliances against over voltage.
DC2DC POWER PRODUCTS Charging Diode Splitters The Enerdrive ePOWER Battery Isolator Charges 2 or More Batteries From 1 Alternator. The ePOWER battery isolators can be used for marine, recreation vehicles or commercial vehicle applications where one or two house batteries are present in addition to a cranking battery. These battery isolators allow charging two or more batteries at the same time from a single charging source, without connecting the batteries together.
DC2DC POWER PRODUCTS DC to DC Converters with Galvanic Isolation Quality DC To DC Converters Featuring Galvanic Isolated Input And Output Terminals. The ePOWER DC to DC galvanic isolation converters are interference free resulting in stable, reliable and efficient power supply. These compact and rugged units omit little heat making them safe and convenient for installation where space is hard to come by.
DC2DC POWER PRODUCTS DC to DC Converters with Galvanic Isolation (Continued) Model Number EN-DC2412-15G EN-DC2412-25G Input (VDC) EN-DC2424-7.5G EN-DC2424-12.5G 20 – 35 Output (VDC) 12.5 24 Current (A) 15 25 7.5 12.5 Load (W) 200 360 200 360 Weight (g) 600g 1400g 600g 1400g Dimension 182 x 88 x 49 mm 160 x 163 x 64 mm 182 x 88 x 49 mm 160 x 163 x 64 mm Model Number EN-DC4812-15G EN-DC4812-25G Input (VDC) EN-DC4824-12.5G EN-DC4848-3.2G EN-DC4848-6.
DC2DC POWER PRODUCTS DC to DC Converters Non Isolated Quality DC to DC Non Isolated Converters that supply stable power to 12 volt equipment. The ePOWER DC to DC non isolated converter supplies stable and efficient power to your low voltage systems such as marine navigation and radio equipment, car hi-fi systems and mobile phone chargers. Poor power supply to your on-board 12V equipment can cause major damage and result in costly replacement of electronic appliances.
DC2DC POWER PRODUCTS DC Motion Sensors P.I.R. Sensor Motion Switch. The ePOWER DCMotion is a motion activated switch for 12v and 24v systems for which a Passive Infra-Red Detector (PIR) is used. Output loads up to 10A (continuous) can be connected to the EN-DCMOTION with the added features of over-voltage, under-voltage and over-current disconnect. For indoor use only. The DCMotion can be used in a number of situations like yacht or ship engine rooms, undercover truck loading bays or RV applications.
DC2DC POWER PRODUCTS NEW FOR 2015 The all new ePOWER 30A DC to DC Battery Charger. Designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems.