Owner’s Manual Enerdrive ePOWER LiFePO4, Lithium Iron Phosphate Battery with Smart Phone Monitoring EPL-100BT-12V • EPL-125BT-12V • EPL-200BT-12V
For safe and optimum performance, the Enerdrive ePOWER LiFePO4, Lithium Iron Phosphate Battery with Smart Phone Monitoring must be used properly. Carefully read and follow all instructions and guidelines in this manual and give special attention to the CAUTION and WARNING statements. PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE Disclaimer While every precaution has been taken to ensure the accuracy of the contents of this guide, Enerdrive assumes no responsibility for errors or omissions.
TABLE OF CONTENTS 1 GENERAL INFORMATION.............................................................................4 2 SMART PHONE MONITORING SYSTEM..................................................5 3 WARNINGS.........................................................................................................6 Low Battery Voltage Disconnect....................................................................................6 4 SPECIFICATIONS.............................................................
1 GENERAL INFORMATION Thank you for purchasing the Enerdrive ePOWER B-TEC Lithium battery. Please read the following information carefully before installing your new battery. This information defines the performance of the rechargable ePOWER LiFePO4 batteries distributed by Enerdrive Pty Ltd and describes the type, performance, technical characteristics and warning of the battery pack. This battery is designed and intended only for use in deep cycle applications where a single battery is required.
2 SMART PHONE MONITORING SYSTEM The Enerdrive ePOWER B-TEC battery incorporates a wireless Smart Phone Monitoring system.
3 WARNINGS Please read and follow the cautions listed on the battery before installation. Improper use may cause heat, fire, rupture, damage or capacity deterioration of the battery. Enerdrive Pty Ltd is not responsible for any accidents caused by the usage without following our specification. WARNING! Failure to follow these instructions may result in early battery failure or possible personal injury. • Do not use the battery for cranking/starting applications.
By continuously tripping the low voltage disconnect of the battery you may cause damage to sensitive electronic equipment that is attached to the battery. I.E battery chargers, solar controllers, inverters, stereo equipment etc, all of which are not covered under the battery warranty. IMPORTANT NOTE USE OF INVERTERS EPL-100BT-12V or the EPL-125BT-12V : If a 230v inverter is to be installed on the battery, a maximum size of 1000w is allowed.
4 SPECIFICATIONS Enerdrive B-TEC 12v Lithium Battery Technical Data Normal Specification EPL-100BT-12V Nominal Voltage EPL-125BT-12V EPL-200BT-12V 12.8V Nominal Capacity 100Ah 125Ah Cycle Life (DOD - 80% under controlled conditions) 200Ah ≥2000 Cycles Standard Charge Specification (Lithium profile charger required) Battery Charge Temperature 0 - 45°C Normal Charge Voltage CV/CC* 14.40 - 14.60V Standby (Float) Voltage 13.50 - 13.
Over-Discharge Protection EPL-100BT-12V EPL-125BT-12V EPL-200BT-12V Over-discharge Protection Per Cell 2.80V ± 0.05V Over-discharge Release Per Cell 3.20V ± 0.05V Over-discharge Release Method Apply Charge/Voltage ≥12.
5 DIMENSIONS EPL-100BT-12V • EPL-125BT-12V EPL-200BT-12V Page 10 Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.
6 STORAGE & TRANSPORTATION Based on the character of the cells, proper environment for transportation of LiFePO4 battery packs need to be created to protect the battery. • Battery should be stored where it’s dry, clean, shaded and well-ventilated at a temperature between -20°C to 35°C • The battery should be stored at approx 50% SOC during transportation.
The ePOWER B-TEC batteries internal management system (BMS) monitors and optimize each single prismatic cell within the battery during charge & discharge. However the BMS does not have the ability of making a physical connection to a second BMS system for balancing of the cells between each battery. So bottom line; Can I parallel connect the ePOWER B-TEC lithium batteries? The short answer is yes. BUT as described above, overall performance of the battery pack and life expectancy will be reduced.
Q: Can I use an Inverter on the ePOWER B-TEC Lithium Battery? A: Yes. You can use a small inverter with the ePOWER Lithium battery. A maximum 1000W inverter is allowed. If a larger inverter is used, then possible damage to the internal BMS system can occur and this will not be covered under warranty.
A: The ePOWER battery is designed to install in the upright position only. Installing it laying on its side or end will damage the lithium cells with the possibility of internal venting from the cell and early failure of the battery will occur, which is not covered under warranty. Q: Can I install the ePOWER B-TEC battery under the bonnet of a car? A: Enerdrive recommend the installation of the battery in a dry, well ventilated cool space.
8 WARRANTY Enerdrive ePOWER B-TEC Lithium Battery Warranty. 1 to 2 Year Limited Warranty Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
this warranty will be repaired/replaced free of charge if, at the sole discretion of Enerdrive, adjustment is necessary due to defect in material or workmanship. Batteries for warranty repair/replacement consideration are to be returned to the original supplying distributor/dealer. Batteries replaced under the warranty provisions will be shipped with a replacement warranty sticker and carry only the remainder of the original Applicable Warranty Period.
General Provisions: Enerdrives Pty Ltd has no obligation under the limited warranty herein in the event the battery is damaged or destroyed as a result of one or more of the following: • Willful abuse, misuse, physical damage, neglect or if the decorative cover has been removed. • Natural forces such as wind, lightning, hail; damage due to fire, collision, explosion, vandalism, theft, penetration or opening of the battery case in any manner. • The battery MUST be installed in an upright position.
Return and/or Repair Policy If you are experiencing any problems with your unit, please contact our customer service department at support@enerdrive.com.au or Phone 1300 851 535 before returning product to retail store. After speaking to a customer service representative, if products are deemed non-working or malfunctioning, the product may be returned to the purchasing store within 30 days of original purchase.
NOTES: www.enerdrive.com.
ENERDRIVE PTY LTD Unit 11, 1029 Manly Road Tingalpa, Queensland, Australia 4173 Ph: 1300 851 535 / Fax: 07 3390 6911 Email: sales@enerdrive.com.au Web: www.enerdrive.com.