Owner manual

ManualsBrandsEnergenics ManualsHardware120 Low Profile Lint Filter (Old)

1470 Don Street • Naples, Florida 34104 Telephone: (239) 643-1711

Fax: (239) 643-6081

Customer Service: (800) 944-1711

Installation & Operation Manual

For ENERGENICS 9002 Control

120 Low Profile Lint Filter

Descriptions Page

Table of Contents 1

Description of Lint Filter Operation 2

Receiving and Installation 3

Important Installation Considerations 4

Exhibit A 5

Warnings/Cautions 6

Dimensions and Erection 7

Sheet Metal Installation 8

Booster Fans/Barometric Dampers 9

Plumbing Requirements 10

Fire Suppression Water System (optional) 11

9002 Control Installation Instructions:

Control Panel (Cover) 9002.0 12

Main Control Box 9002.1 13

Transformer Box 9002.2 14

Pressure Input Box 9002.3 15

Timer Box 9002.3A 16

Main Control Box (Electrical Schematic) 9002.4 17

Maintenance Requirements 18

Parts List 19

Summary of content (19 pages)

PAGE 1
470 Don Street • Naples, Florida 34104 Telephone: Fax: Customer Service: (239) 643-1711 (239) 643-6081 (800) 944-1711 Installation & Operation Manual For ENERGENICS 9002 Control 120 Low Profile Lint Filter Descriptions Page Table of Contents 1 Description of Lint Filter Operation 2 Receiving and Installation 3 Important Installation Considerations 4 Exhibit A 5 Warnings/Cautions 6 Dimensions and Erection 7 Sheet Metal Installation 8 Booster Fans/Barometric Dampers 9 Plumbing Requirem
PAGE 2
DESCRIPTION OF LINT FILTER OPERATION Your new Energenics Lint Filter represents the most advanced features available in the laundry industry to date. The following list the functions and mode of operation: Blowdown (cleaning) – The Lint Filter will monitor the system backpressure and automatically initiate the blowdown cycle. On the main control the Normal Light will be lit when the system senses airflow from the dryers.
PAGE 3
Receiving and Installation Before you sign the Bill of Lading: 1. Receiving- Inspect units inside and out for signs of damage Verify all components are delivered per the Bill of Materials. Report damage to the carrier IMMEDIATELY. Note ALL damage on the Bill of Lading. This is your responsibility and you must file all claims. The filter is fully assembled and ready for installation. The control, valves, lint bag is in a cardboard box. Make sure both are complete. Per Exhibit A. 2.
PAGE 4
Important Installation Considerations All Energenics Lint Collectors can be mounted indoors or outdoors. If it is mounted outdoors we recommend our Side Discharge or a field installed swept radius elbow (Gooseneck). Do not use a “China type” cap on the discharge. The Pressure transducer should be mounted on top of the filter to prevent condensation running down the tubes into the pressure switch located in the pressure input box.
PAGE 5
PAGE 6
Warning and Caution You have purchased the finest lint filter available for your facility. Please follow these instructions to ensure a safe long life for your filter and facility. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN AN UNSAFE OPERATING CONDITION, INCLUDING THE POSSIBILITY OF FIRE. DO NOT OPERATE ANY DRYER CONNNECTED TO THIS FILTER WITHOUT BEING CERTAIN THE FILTER STARTUP HAS BEEN COMPLETED AND THE FILTER IS IN OPERATING CONDITION. Insure it is installed in compliance with local codes.
PAGE 7
PAGE 8
PAGE 9
PAGE 10
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 15
PAGE 16
PAGE 17
PAGE 18
Maintenance Requirements The frequency of your maintenance requirements depends upon the number of hours of operation and upon variances in your product output. For a single-shift operation, without special problems, the frequency recommended below should suffice. You should set your own schedule based on your experience. 1. WEEKLY Visually inspect the filter inside and outside, its controls and their operation. At time of such inspection, note and correct any discrepancies from normal operation. 2.
PAGE 19
MODEL 120 PART NUMBER DESCRIPTION 1213 Rotor Support 1214 Rotor 1215 Hood With Rain Bonnet 1211 Hood Without Rain Bonnet 12570 Lint Screen With Cables (210 Micron) 12580 Lint Screen Without Cables (210 Micron) B120 Lint Bag (76” x 27 ½”) 13920 Flex Connector 6557 3/4” Air Solenoid Valve (24 VAC) 6557 3/4" Water Solenoid Valve (24 VAC) 6015 Fenwall Fire Sensor 6690 Spray Head (Water Nozzle) 90002 9002 Main Control Box 9001PC 9001 PC Board 9002PC 9002 PC Board 90001 Pressure Input Box 4211 Siren Alarm 4210