Manual

ManualsBrandsEnergenics ManualsHardware150 Low Profile Lint Filter (Old)

1470 Don Street • Naples, Florida 34104 Telephone: (239) 643-1711

Fax: (239) 643-6081

Customer Service: (800) 944-1711

Installation & Operation Manual

For ENERGENICS 9002 Control

150 Low Profile Lint Filter

Descriptions Page

Table of Contents 1

Description of Lint Filter Operation 2

Receiving and Installation 3

Important Installation Considerations 4

Exhibit A 5

Warnings/Cautions 6

Dimensions and Erection – Leg Supports 7

Dimensions and Erection – Roof Curb Cover 8

Sheet Metal Installation - Outdoors 9

Sheet Metal Installation – Indoors 10

Booster Fans/Barometric Dampers 11

Plumbing Requirements 12

Fire Suppression Water System (optional) 13

9002 Control Installation Instructions:

Control Panel (Cover) 9002.0 14

Main Control Box 9002.1 15

Transformer Box 9002.2 16

Pressure Input Box 9002.3 17

Timer Box 9002.3A 18

Main Control Box (Electrical Schematic) 9002.4 19

Maintenance Requirements 20

Parts List 21

Summary of content (21 pages)

PAGE 1
470 Don Street • Naples, Florida 34104 Telephone: Fax: Customer Service: (239) 643-1711 (239) 643-6081 (800) 944-1711 Installation & Operation Manual For ENERGENICS 9002 Control 150 Low Profile Lint Filter Descriptions Page Table of Contents 1 Description of Lint Filter Operation 2 Receiving and Installation 3 Important Installation Considerations 4 Exhibit A 5 Warnings/Cautions 6 Dimensions and Erection – Leg Supports 7 Dimensions and Erection – Roof Curb Cover 8 Sheet Metal Installat
PAGE 2
DESCRIPTION OF LINT FILTER OPERATION Your new Energenics Lint Filter represents the most advanced features available in the laundry industry to date. The following list the functions and mode of operation: Blowdown (cleaning) – The Lint Filter will monitor the system backpressure and automatically initiate the blowdown cycle. On the main control the Normal Light will be lit when the system senses airflow from the dryers.
PAGE 3
Receiving and Installation Before you sign the Bill of Lading: 1. Receiving- Inspect units inside and out for signs of damage Verify all components are delivered per the Bill of Materials. Report damage to the carrier IMMEDIATELY. Note ALL damage on the Bill of Lading. This is your responsibility and you must file all claims. The filter is fully assembled and ready for installation. The control, valves, lint bag is in a cardboard box. Make sure both are complete. Per Exhibit A. 2.
PAGE 4
Important Installation Considerations All Energenics Lint Collectors can be mounted indoors or outdoors. If it is mounted outdoors we recommend our Side Discharge or a field installed swept radius elbow (Gooseneck). Do not use a “China type” cap on the discharge. The Pressure transducer should be mounted on top of the filter to prevent condensation running down the tubes into the pressure switch located in the pressure input box.
PAGE 5
PAGE 6
Warning and Caution You have purchased the finest lint filter available for your facility. Please follow these instructions to ensure a safe long life for your filter and facility. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN AN UNSAFE OPERATING CONDITION, INCLUDING THE POSSIBILITY OF FIRE. DO NOT OPERATE ANY DRYER CONNNECTED TO THIS FILTER WITHOUT BEING CERTAIN THE FILTER STARTUP HAS BEEN COMPLETED AND THE FILTER IS IN OPERATING CONDITION. Insure it is installed in compliance with local codes.
PAGE 7
PAGE 8
PAGE 9
PAGE 10
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
Maintenance Requirements The frequency of your maintenance requirements depends upon the number of hours of operation and upon variances in your product output. For a single-shift operation, without special problems, the frequency recommended below should suffice. You should set your own schedule based on your experience. 1. WEEKLY Visually inspect the filter inside and outside, its controls and their operation. At time of such inspection, note and correct any discrepancies from normal operation. 2.
PAGE 21
MODEL 150 PART NUMBER DESCRIPTION 1513 1514 1511 1508 1501 15570 15580 B150 10140 6558 6557 6015 6690 90002 9001PC 9002PC 90001 4211 4210 90009 90003-OLD 90003 Rotor Support Rotor Hood – Outlet Rain Bonnet Bottom Cone With Inlet Lint Screen With Cables (210 Micron) Lint Screen Without Cables (210 Micron) Lint Bag (60” x 27 ½”) Flex Connector 1” Air Solenoid Valve (24 VAC) 3/4" Water Solenoid Valve (24 VAC) Fenwall Fire Sensor Spray Head (Water Nozzle) 9002 Main Control Box 9001 PC Board 9002 PC Board Pre