SAFETY AND OPERATING MANUAL Original Instructions V7.0 3.
Read all safety warnings and all instructions before use. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 3.
GENERAL SAFETY INSTRUCTIONS WARNING. Read all safety warnings and instructions. Failing to follow the warnings and instructions can result in an electric shock, a fire and/or a serious injury. Keep all warnings and all instructions to be able to refer to them later on. The term “tool” in the warnings refers to your electrical mains powered tool (with power cord) or your battery operated tool (without power cord). 1 Safety of the work area a) Keep the work area clean and well lit.
Use and maintenance of the tool a) Do not force the tool. Use the correct tool for your application. The correct tool will do the work better and safer in the conditions for which it was manufactured. b) Do not use the tool if the switch does not make it possible to change from the operating condition to stop and vice versa. Any tool which cannot be controlled by the switch is dangerous and should be repaired.
SPECIAL SAFETY INSTRUCTIONS 1. Hold power tool by insulated gripping surfaces, when performing an operationwhere the fastener may contact hidden wiring or its own cord. Fasteners contacting a"live" wire may make exposed metal parts of the power tool "live" and could give theoperator an electric shock. 2. Remove the battery pack from the drill before carrying out adjustments. 3. Do not expose to rain or water. 4. Do not store the battery pack in temperatures over 40°C. 5.
Use the appliance only with the type of battery/ battery pack indicated in the instructions. Using another type of battery/ battery pack can create a serious risk of injury and cause a fire. When the battery/ battery pack is not in use, keep it away from metal objects such as trombones, coins, keys or other small metal objects that can create a connection between one terminal and the other. Short-circuiting the terminals of batteries can cause burns to the user and cause a fire.
NOISE INFORMATION Wear hearing protection! Measured sound values determined according to EN 60745. The noise figures quoted are emission levels and are not necessarily safe working levels. Whilst there is a correlation between the emission and exposure levels, this cannot be used reliably to determine whether or not further precautions are required. Factors that influence the actual level of exposure of work-force include the characteristics of the work room, the other sources of noise, etc. i.e.
Vibration and noise reduction To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment. Take the following points into account to minimize the vibration and noise exposure risks: 1.Only use the product as intended by its design and these instructions. 2.Ensure that the product is in good condition and well maintained. 3.
SYMBOLS The symbols shown on the product has great significance for the safe use of the product. WARNING - To reduce the risk of injury, user must read the instruction manual Wear safety gloves Wear eye protection Wear ear protection Wear respiratory protection Double insulation Class II Conforms to all relevant safety standards.
Components and controls 6 7 1 2 3 4 5 6 7 Bit holder LED Working light On/off switch Forward/reverse lever Power/Rotation direction Indicator Light green=forward/red=reverse Charger Belt holster 3.
TECHNICAL DATA Rated voltage: No load speed: Machine weight: Normal charging time: Battery ENS460DRS 3.6V 180 min-1 0.37kg 3-5 hours 3.6V li-ion, 1300mAh 4.68Wh Charger PRI: 230-240V~50Hz 4W SEC: 5V 300mA NOISE INFORMATION Sound pressure level : LpA = 58.9 dB(A) Uncertainty K=3dB(A) Sound power level : LwA =69.
CHARGING PROCEDURE 1. BEFORE USING THE SCREWDRIVER If the machine is new, the battery must first be charged. A new battery or one which has not been used for an extended period achieves full performance only after few times charging and discharging cycles. Attention! After storing for a long time, the battery capacity will be reduced. A substantial drop in operating period per charge indicates that the battery is worn out.
Operating instructions 1. INSTALLING AND REMOVING BITS 1.To fit a screwdriver bit, push it into the bit holder until it locates. 2.To remove a screwdriver bit, pull it straight from the bit holder.(Fig.1) Make sure it is fully in place before use. 2. ON/OFF SWITCH 1.Start the tool by squeezing the On/Off Switch(3). 2. Release the switch to stop the machine. Fig.1 3. SWITCH LOCK The On/Off switch trigger can be locked in OFF position.
TERMS OF USE When all precautions have been taken and the previous operations were done, you can start working. Always secure the work piece especially if it is small and the sheets. Use the appropriate drill bit and the material at the correct speed. Stay in the extension of the machine, perpendicular to the surface to be drilled. CARE AND MAINTENANCE This machine requires no special mechanical maintenance such as greasing the bearings.
ENVIRONMENTAL PROTECTION This product is marked with the selective sorting symbol on waste electrical and electronic equipment. This means that this product should not be disposed of with household waste but must be supported by a collection system in accordance with Directive 2002/96/EC. It will then be recycled or dismantled to minimize impacts on the environment, electrical and electronic products are potentially hazardous to the environment and human health due to the presence of hazardous substances.
Declaration of Conformity We, Importer Powersmith (UK) LTD. Trade house, Mead Avenue, BA22 8RT Declare that the product: Designation: SCREWDRIVER 3.