Use and Care Manual

ManualsBrandsEnergin ManualsOutdoors4,000-Watt XLT Gasoline Powered Electric Start Generator with Wheel Kit

8807517 12/7

4000 XLT GENERATOR Models: 9224, 52223

CALIFORNIA PROPOSITION 65

WARNING: You can create dust

when you cut, sand, drill or

grind materials such as wood,

paint, metal, concrete, cement,

or other masonry. This dust

often contains chemicals

known to cause cancer, birth

defects, or other reproductive

harm. Wear protective gear.

WARNING: This product or its

power cord may contain

chemicals, including lead,

known to the State of California

to cause cancer and birth

defects or other reproductive

harm. Wash hands after

handling.

CAUTION:

FOR YOUR OWN SAFETY

READ INSTRUCTION MANUAL

COMPLETELY AND

CAREFULLY BEFORE

OPERATING THIS GASOLINE

ENGINE Failure to follow all

instructions as listed below

may result in electrical shock,

fire, and/or serious personal

injury.

SPECIFICATIONS:

Engine: 4-stroke; Single phase;

Electronic ignition

Start Type:Recoil & Electric Start

Rated Power: 3500W

Fuel Capacity: 4gallons

Run Time:9 hours

SAFETY WARNINGS

1) Do not operate this generator

indoors or in enclosed spaces.

Emissions created by this

generator are harmful.

2) Do not operate the generator in

wet conditions. This will increase

the risk of electrical shock.

3) Do not directly connect the

generator to a household power

supply.

4) Do not smoke while refueling

the generator. Do not overflow the

fuel when refueling the generator.

Stop the generator before

refueling. Gasoline is

flammable and the sparks may

cause it to ignite. Keep the

generator at least 3 feet away

from flammable materials.

5) Electrical equipment,

including any lines and plug

connections, should be

insulated.

6) The circuit breakers should

be matched with the generator

equipment. If the circuit

breakers need replacement,

they must be replaced with a

breaker that has identical

ratings and performance

characteristics.

7) Do not operate the generator

before grounding it. An

ungrounded generator could

cause electrical shock to occur.

8) The temperature of the

environment will affect the

overcurrent protector. Please

change the protector so it will fit

with the local environment

temperature.

For customer service, call 1-800-348-5004 or email

For warranty purchase, please keep your dated proof of purchase. File or attach to the manual for safekeeping.

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this

product. Observe all safety information to protect yourself and others. Failure to observe the instructions may

result in property damage and/or personal injury. Please keep instructions for future reference.

feedback@natitools.co

Important Operating Instructions

Summary of content (14 pages)

PAGE 1
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property damage and/or personal injury. Please keep instructions for future reference.
PAGE 2
9) Keep your work area clean and well lit. Do not wear loose clothing or jewelry. Keep long hair pulled back. 10) Do not overload the generator. Do not force a small generator to do the job of a large one. 11) Do not use the generator if the power switch does not properly turn it on and off. 12) Do not use damaged generator. 13) Wipe up any gasoline spills that may have occurred during refueling before starting the generator.
PAGE 3
.Turn the Engine Fuel Valve to its "ON" position. Then turn the Engine Choke Lever to its "CLOSE" position. No choke is required if the Engine is warm. Make sure the Choke Lever is in the "OPEN" position when starting a warm Engine.(See Figure D.) Then, pull the Starter Handle(See Figure E.)with a rapid, full arm stroke. Allow the Rope to rewind slowly. If necessary, repeat this procedure until the Engine starts. 3.
PAGE 4
6.Always power the largest electric motor first. Then, plug in other appliances, tools, and equipment. a.Connect "inductive" load appliances, tools, and equipment first. Inductive loads consist of small hand tools and some small appliances. Connect the items that require the most wattage first. b.Connect any lights next. c.Voltage sensitive appliances, tools, and equipment should be the last to be connected to the Generator. Plug voltage sensitive items such as T.V.
PAGE 5
. Be sure to reinstall the cap when finished checking the oil oil filler cap Air Cleaner Maintenance oil filler cap Routine maintenance of the air cleaner helps maintain proper air flow to the carburetor. Occasionally check that the air cleaner is free of excessive dirt. oil filler hole Drain plug Figure H Figure G Changing/ Adding Oil You should check the oil level of your generator.When the oil level is low you will need to add oil until the level is sufficient to run the generator.
PAGE 6
Fuel Filter Cup Cleaning The fuel filter cup is a small well underneath the fuel valve. It helps to trap dirt and water that may be in your fuel tank before it can enter the engine. To clean the fuel filter cup. 1. Turn the fuel valve to the "off" position. 2. Unscrew the fuel filter cup from the fuel valve using a wrench. Turn the valve toward you to unscrew (see figure K). 3. Clean the cup of all sediment using a rag or brush. Visually inspect the spark plug.
PAGE 7
Recommended Maintenance Schedule first month of each use Engine oil check level check 50 hrs x x gas tank check gas level As or 300 hrs necessary x x x x x Clean feedback@natitools.
PAGE 8
Troubleshooting Guide feedback@natitools.
PAGE 9
Limited Manufacturer Warranty North American Tool (NAT) Industries makes every effort to ensure that this product meets high quality and durability standards. NAT warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.
PAGE 10
4000 XLT GENERATOR Models: 9224, 52223 Parts List - Generator For customer service, call 1-800-348-5004 or email feedback@natitools.
PAGE 11
Parts List Call 1-800-348-5004 for assistance or replacement parts Please provide the following information -Model number -Part description and number as shown in parts list -Serial number Address any correspondence to: North American Tool Industries 84 Commercial Rd Huntington, IN 46750 feedback@natitools.
PAGE 12
4000 XLT GENERATOR Models: 9224, 52223 Parts List - Engine For customer service, call 1-800-348-5004 or email feedback@natitools.
PAGE 13
Parts List Call 1-800-348-5004 for assistance or replacement parts Please provide the following information Address any correspondence to: -Model number North American Tool Industries 84 Commercial Rd Huntington, IN 46750 -Part description and number as shown in parts list -Serial number No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Spare parts code 2.55.07.001000 2.55.06.000100 2.55.05.005206 2.55.05.005201 2.55.
PAGE 14
Wire Diagram feedback@natitools.