ENX8K Lithium Battery Disposal: This product contains a lithium battery. A lithium battery should not be thrown away in the trash. Please dispose of the battery at an authorized disposal or recycle center. Check your local requirements for battery disposal/recycling in your state. Made in China for: Bright Manufacturing LLC. Fort Lauderdale, FL 33309 © 2017 Energizer.
INTRODUCTION Please read this manual thoroughly before installing and operating your new Energizer® Lithium-Polymer Car Jump Starter. This manual contains information you need to obtain relating to the performance required for your application. Keep this manual for future reference. IMPORTANT SAFETY INFORMATION Misusing or incorrectly connecting the Jump Starter may damage the equipment or create hazardous conditions for users.
SPECIFICATIONS (Specifications are subject to change without notice.) Battery Capacity: 30,000mWh Starting Current: 200A Peak Current: 500A DC Charge Input: 5V 1A/2.1A Rated USB Output: 5V/max, 2.4A (iPad) Temp (Environment): -25°C to 40°C / -13°F to 104°F Physical Specifications: Dimensions (L x W x H): 5.5in x 3.2in x 0.8in / 140mm x 83mm x 20mm Weight: 0.65 lbs / 0.
SAFETY INFORMATION Please read this entire manual before attempting to use this product. WARNING Avoid dangerous environments. Do not charge this item in rain, snow, damp or wet environments. Do not use this item or charger in the presence of explosive atmospheres (gaseous fumes, dust or flammable materials) since sparks may be generated when inserting or removing this item, possibly causing fire. Charge in a well-ventilated area. Do not allow smoking or open flames near a charging battery.
OPERATING INSTRUCTIONS Make sure power level is above 50% before use: Indicator 0 1 2 3 4 Battery charger 0% 25% 50% 75% 100% Plug the blue connector into the 12V Jump Starter port (A); LED (B) illuminates red. 1. Connect the red damp to positive '+' on the vehicle's battery. Connect the black clamp to negative '-' on the vehicles battery. lf connected correctly LED (B) illuminates green.
TROUBLE SHOOTING Problem Jump starter does not jump start vehicle. Red blinking Possible Cause Solution 1. Battery may not 1. Charge the jump starter have sufficient to sufficient charge. charge. 2. Reconnect the clamps 2. Jumper cable clamps to the proper battery maybe improperly terminals, and ensure connected to the the jumper cable’s LED vehicle’s battery. is illuminated green 3. Over temperature 3. Make sure the Jump starter cooled to usage temperature Jump starter does not jump start vehicle.
1. Disconnect the Jump starter within 30 seconds after starting your car. 2. Do not connect the red clamp and black clamp directly. 3. Do not disassemble themachine. IMPORTANT SAFETY INSTRUCTIONS WARNING – When using this product, basic precautions should always be followed, including the following: a) Read all the instructions prior to using the product. b) To reduce the risk of injury, close supervision is necessary when the product is used near children. c) Do not put fingers or hands into the product.
those published by battery manufacturer and manufacturer of any equipment you intend to use in vicinity of the battery. Review cautionary marking on these products and on engine. l) PERSONAL PRECAUTIONS 1) Consider having someone close enough by to come to your aid when you work near a lead-acid battery. 2) Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. 3) Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.
A- Spring-loaded fully insulated colored coded clamps B- 12V jump starter connector & port C- Cross polarity safety function. Fully protected against short circuiting D- USB 2.4A output suitable for most USB devices including smart phones, tablets, iPhone, iPad, and iPod E- On/off button _ Led Light button F- DC charge input G- Battery level indicator lights Your Energizer Jump Starter can be charged with any USB charging device.
WARRANTY AND RETURNS What does the warranty cover? This Limited Warranty is provided by Bright Manufacturing and covers defects in workmanship and materials in your model ENX8KK Jump Starter. This warranty period lasts 12 months from date of purchase at the point of sale to you, the original end user customer. Proof of purchase is required to make warranty claims.
2. The product if it has been subjected to fire, water, generalized corrosion, biological infestations, or input voltage that creates operating conditions beyond the maximum or minimum limits listed in the Bright Manufacturing product specifications including high input voltage from generators or lighting strikes; 3. The product if repairs have been done to it other than by the Energizer Warranty Department. 4.
