User Manual
1. Important Safety Instructions To ensure your safety and the safety of others, please ensure that you read all the safety information before operating this product. Keep this information in a safe place for future reference. This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Safety Considerations.
Cleaning ALWAYS unplug the set top box before you clean it. Do not use liquid or aerosol cleaners. Clean the set top box with a soft, damp (not wet) cloth. P3450 Handling And Care Place the product in a well-ventilated area. Don’t install it in the cold or under direct sunlight.
2. FRONT Panel 2 1 1. 2. 3. 4. 5. 3 4 Power / Standby key Power / Standby LED indicator IR Receiver SD/SDHC Card reader USB Host port 3. REAR Panel 7 3 1 2 4 5 6 8 9 1. DC IN 2. MINI USB Device 3. Power Switch 4. HDMI connector 5. IEC Antenna connector 6. Loop through connector 7. YPbPr Component output 8. AV Composite output 9. Scart Connector 10.
4. Remote Control 4.1. Button descriptions 1 2 3 4 5 6 7 9 10 8 1. 2. 3. 4. 5. 6. 7. 8. 9. 12 11 13 16 14 16 15 20 19 24 23 25 28 17 18 21 22 26 27 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Note: SUB-T/TTX/AUDIO/EPG may not be available for all channels. 21. 22. 23. 24. 25. 26. 27. 28. POWER: Switches P3450 to on or standby mode. MUTE: Mutes / unmutes the sound. NUMERIC BUTTONS: Selects a channel or setting. EXIT: Exits current menu or returns to previous option.
4.2. Installing the Batteries Remove the battery cover from the remote control and put 2xAAA size batteries inside the compartment. The following diagram shows the correct way to insert batteries. 1. Open the cover O PE 2. Install batteries N 3. Close the cover CL O SE ≥≥ Keep batteries out of reach of children. If someone swallows a coin cell or battery must receive immediate medical attention. ≥≥ Do not attempt to reactivate the batteries using heat, loading, or by other means.
5. CONNECTION Caution: Make sure the outlet voltage is the same as the receiver. To avoid the risk of electric shock do not open the cover or the back of the receiver when P3450 is connected to mains supply. 5.1. CONNECTING THE INTERNAL HARD DISK SATA 3.5” If your model of P3450 is not provided with an internal hard disk already installed, please follow the step by step instructions below to connect it to the player. Unplug P3450 from mains supply before starting the hard disk installation. 1.
4. Place the hard disk into the holder in the correct position and fix the HDD to the base with four screws 5. Carefully slide the top cover to the original position and replace the screws. 5.2. Partitioning and Formatting Hard Disk Drive Newly purchased hard disks are not usually formatted or partitioned. Nonformatted hard disks cannot be detected by P3450; if so, make it usable first by formatting with a computer. For that purpose, we recommend you to use the usb connector.
5.2.1. Windows 2000/XP 1. Select [Start>Control Panel>Management Tools>Computer Management] and then [Disk Management] under [Storage] section. 2. In the list of connected disks locate the one that corresponds to P3450. 3. Activate the disk using MBR partition table (GUID partition table is not supported) if it is not already activated. To create a FAT32 or NTFS partition: 4.
5. ‘New Partition Wizard’ will show. Click [Next] to continue. 6. Select [Primary Partition] and click [Next] to continue. 7. Enter the desired partition size and click [Next] to continue.
8. Assign a drive letter to the partition (you can accept the letter suggested by the wizard), click [Next]. 9. Select [Format this partition with the following settings]; FAT32 or NTFS as [File system] and then check [Perform a quick format]. Click [Next] to continue. 10. Check the settings are correct and click [Finish]. Windows will perform the requested operations to create the new FAT32 or NTFS partition.
5.2.2. Windows Vista 1. Right click on the ‘Computer’ icon in your desktop and select ’Manage’. 2. At the ‘Computer Management’ window select ‘Storage > Disk Management’. 3. Select the hard disk that refers to P3450 on the right side panel. 4. If necessary, activate the hard disk right-clicking on ‘Disk n *’.
5. Right click the hard disk bar and select ‘New Simple Volume’. 6. The ‘New Simple Volume Wizard’ will start. Click ‘Next’ to continue. 7. Specify the desired partition size. 8. Assign a drive letter to the partition (you can accept the letter suggested by the wizard). Click ‘Next’ to continue.
9. In this step leave all the default values unchanged and click ‘Next’ to continue. 10. Click ‘Finish’ to start the actual formatting. 11. When the formatting is over the text ‘Healthy (Primary Partition)’ will be shown confirming that the disk is ready to use.
5.2.3. Windows 7 1. Open Computer Management by clicking the Start button , clicking Control Panel, clicking System and Security, clicking Administrative Tools, and then double-clicking Computer Management. If you're prompted for an administrator password or confirmation, type the password or provide confirmation. 2. In the left pane, under Storage, click Disk Management. 3. Right-click an unallocated region on your hard disk, and then click New Simple Volume. 4. In the New Simple Volume Wizard, click Next.
5.3. CONNECTING P3450 TO TV AntenaTV TV 5.4.
5.5. CONNECTING P3450 TO AUXILIARY DEVICES VCR Coaxial VOLUME INPUT SELECTOR POWER BYPASS PRO LOGIC 3 STEREO MODE TEST CHANNEL KARAOKE MUTE UP DOWN 1 MIC 2 1 MIC VOL 2 BASS EXCITE MIC TREBLE ECHO Amplificador Digital Note: When connecting the receiver to other equipment (e.g. TV, VCR and amplifier), make sure to refer to relevant user manual for instruction. Also, make sure you disconnect all the equipments from the mains supply before the connection.
6. USER INTERFACE – multimedia MAIN MENU There are seven different options in the main menu screen. 6.1. SETUP The Setup menu allows you to personalize and configure the preferences for your player. To select a Setup option: There are four Setup options, including SYSTEM, MOVIE, PHOTO and FORMAT. Use the LEFT/RIGHT navigational buttons to select a menu. Press OK to confirm. Press EXIT to exit the sub-setup menu.
6.1.1. System It will allow you to change system settings. Language: The system language of this player is set to Spanish as default, but it can be set to English or other languages. Change the language you wish in the setup menu. The selection will take effect immediately. Aspect Ratio: AUTO: Display picture or movie on original aspect ratio. 4:3 Full: Display picture or movie on the full screen. Pan Scan 4:3: Display a wide picture on the entire screen and cuts off the redundant portions.
6.1.2. Movie It will allow you to change movie settings. SUBTITLE SPECIFIC: Select the subtitle size specification: NORMAL/ SMALL/ BIG. SUBTITLE BG: Select to adjust subtitle background colour: TRANSPARENT/ YELLOW-GREEN/ WHITE/ GRAY. SUBTITLE FONT COLOR: Select to adjust subtitle font colour: White, black, red, green or blue. START RESUME: Select to turn on / off resume playback (auto-bookmarking) feature for movies. 6.1.3. Photo It will allow you to change photo settings.
6.2. PHoto In photo play mode, all folders and supported photos in current directory will be displayed. Please set the preview item as “on” in setup. The following buttons can be used to control photo playback. Button Function UP/DOWN Move the cursor up/down. When the picture is on Fullscreen, rotate a photo in any angle. REPEAT When selected picture is on Fullscreen, set play mode options: Repeat All, Ordinal, Shuffle. OK Play selected picture on Fullscreen. PLAY/PAUSE Begin or pause slideshow.
6.3. Music In music play mode, all folders and supported music files in current directory will be displayed. The following buttons can be used to control music playback. Button Function UP/DOWN Move the cursor up/down. OK Preview the music on the right window. Please set the preview item as “on” in setup. REPEAT Set repeat options: Ordinal, One, All, Shuffle. PLAY/PAUSE Start or pause playback. REV/F.F Fast rewind or fast forward. Press repeatedly to select the speed. STOP Stop playback.
them in slide show mode or at any time. The playlist will be saved on the current partition. Adding files to the playlist: Select the favourite file you wish to add, press the” Right” direction key, and the file will be ticked. Press the FAV button to confirm, and then a PLAYLIST MODE will be shown. Delete files from the playlist: Select the destination file, press the RIGHT button ,and the file will be marked, and then press OK to delete them immediately ,or will be delete when you exit the playlist. 6.4.
GOTO Press to jump to a specific point on the playback. RED ENTER/EXIT Fullscreen mode. 16:9 Switch screen aspect ratio. AUDIO Switch audio tracks (if available). 6.5. Browser In browser mode, all folders and supported contents (music, photos, and movies) will be displayed. The following buttons can be used to control Browser mode. Button Function UP/DOWN Move the cursor up/down. BLUE Select the files which will be deleted.
6.6. DVB-T 6.6.1. First Time Installation When you are using the DVB-T TV player for the first time or restored to Factory Default, the Installation Guide dialog box will appear on your TV screen with the following options. OSD Language: you can choose the language. Country: you need choose the country before starting the channel searching. Channel search: start to auto search channels. Note: You can also choose “manual search” for channel searching in the TV Player Setup Menu.
6.6.2. DVB-T Setup Menu Press “MENU” key to enter the DVB-T TV Setup Menu. There are six different options: 6.6.2.1. Program Program edit: press right key to enter program edit sub-menu.
In this mode the four colour keys will be used under this mode: Move: yellow Skip: Green Lock: Red Delete: Blue Rename: Goto. Choice the object channel, and press “GOTO” key to show the soft keyboard. You can now rename the program using it. Grouping: FAV. Choose the channel, then press FAV key to show the group list (Disable, Movie, News, Sport, Music, and Entertainment). Select the group and press OK, and it will appear a red heart icon on the left to confirm. Press OK again if you want to cancel.
EPG (Electronic Program Guide): press “OK” to show the seven days program information for the current channel (availability depends on broadcasting channel). LCN (Logical Channel Number): Press left /right key to switch LCN ON /OFF. Sort: Press right key to choose how to sort the channels: by LCN, ONID, Service Name, Service ID. 6.6.2.2. Channel search Auto Search: press right key start to auto scan all frequency. Manual Search: press right key start to manual search setting.
6.6.2.5.System Parental Guidance: press left/right key to set the minimum age level for the program. The default password is: 888888 Set password: Press right key to enter the password setting sub-menu, and then use the numeric key on the RC to set the password. Factory default: Press right key to restore the default settings. The default password is: 888888 Information: Press right key to show the system information (model number, SW Version, HW Version). 6.6.2.6.
6.6.3. DVB-T Playback mode The following buttons can be used to control DVB-T Playback mode. Button Function CH+/CH- Press to view previous/next channel. INFO Press to show the channel basic information. If you want to view detailed information (such as frequency or bandwidth), just press info key twice. SUB-T Press to choose the subtitles. This is only available if the channel has multi-subtitles. AUDIO Press to choose the audio track. This is only available if the channel has multi-audio tracks.
6.6.4. DVB-T Recording Mode The following buttons can be used to control DVB-T recoding mode. Button Function REC Press to start recording directly. YELLOW Under PVR booking menu, press to add a recording schedule. Under EPG menu, press to start EPG reservation recording. RED Press to edit the recording schedule. BLUE Press to delete a recording schedule under recording schedule menu. GREEN Press to enter the PVR booking menu.
6.6.4.2. Scheduled recording: 6.6.4.2.1. Manual Reservation Recording Press “Green” key to enter the Schedule mode and open PVR booking menu. Then press “yellow” key to add the current recording task. You can use ”Red” or ”Green” keys to edit or delete any existent booking. Press “OK” to confirm the scheduled recording and save the changes. 6.6.4.2.2.EPG Reservation Recording Press EPG to show the TV programs list. Choose the program you want to record and click OK or “yellow” to confirm the selection.
6.6.4.3. Timeshift Press “Timeshift” key to start recording the program you want to review. Then you can press “FR” or “FF” key to select the recorded segment you want to watch or review, while the recording process continues its normal course. Press “STOP” key to exit timeshift. Press “INFO” key to show detailed information, hide the timeshift bar or show it again. 6.7. PVR In PVR mode, all folders and supported videos already recorded in current directory will be displayed.
Mosaic blocks in picture or picture freezes Aerial may not be compatible Check aerial Scrambled channel message Channel is scrambled Select an alternative channel No response to remote control Receiver off Plug in and turn on receiver Front panel obstructed Check for obstructions Remote control batteries are inserted incorrectly Check batteries direction Remote control batteries exhausted Replace remote control batteries After moving the device to The aerial feed may come another room can’t re
8. TECHNICAL SPECIFICATION Item Specification Vídeo Resolution 576p, 720p, 1080i, 1080p Aspect Ratio 4:3 (Letterbox, Pan & Scan) & 16:9 Output Port HDMI, Composite, Component, Scart Audio Output Optical Power AC/DC Adapter Input Voltage AC 100V - 240V 50Hz -60Hz AC/DC Adapter Output Voltage DC 12V - 3A Multimedia Format Video MPEG 1/2/4 (VOB, MPG, TS, MOV, MP4), AVI (DivX, Xvid, H.264), MKV (H.
Supported Video Specifications: File Extension Container Video Codec SPEC Bit Rate Profile mpg, mpeg MPG, MPEG Mpeg 1,2 1920x1080 @ 30P 20Mbit/s Main Profile ts, m2ts MPEG2 -TS H264-TS MPEG2 ,H.264 1920x1080 @ 30P 20Mbit/s H264: Main Profile y High Profile @Nivel 4.0 MPEG2: Main Profile vob MPEG2 -PS MPEG2 1920x1080 @ 30P 20Mbit/s Main Profile AVI, MP4 MPEG4 Divx 4.12, Divx 5.x, Divx 6, Xvid 1.01, Xvid 1.02, Xvid 1.03, H.264 20Mbit/s H264: Main Profile y High Profile @Nivel 4.
divx, avi AVI(1.0, 2.0), DMF0,1,2 MPEG2, MPEG4 Divx 4.Divx 5, Divx 6, Xvid 1.01, Xvid 1.02, Xvid 1.03, H.264 1920x1080 @ 30P 20Mbit/s MPEG2: Main Profile MPEG4: Simple Profile y Advanced Simple Profile @Nivel 5 Comment: MP4: GMC is not supported 9. WARRANTY Energy Sistem Soyntec S.A. warrants its products to be free from defects in materials and workmanship at the time of purchase. The warranty period is 36 months from the date of purchase for your Multimedia Player & DVB-T Recorder Receiver.
TRADEMARKS All company, brand and product names are trademarks or registered trademarks of their respective companies. DECLARATION OF CONFORM ITY Manufacturer Name: Energy Sistem Soyntec S. A. NIF: A53107488 Address: Pol. Ind. Finestrat.
www.energysistem.
