User`s guide

ManualsBrandsENERGY SISTEM Manualscomputers & electronicsLinnker 5000

User’s Guide

1.Assemble and disassemble the ear-hook

with the Headset

(1)To assemble the ear-hook with the

Headset, push the toggle of the ear-phone

into the pin-hole of the ear-hook. To disassemble the ear-hook with the Headset, just

turn and pull out the toggle of the ear-phone from the pin-hole of the ear-hook.

(Please refer to Fig.1)

(2)Fit the ear-hook with your right or left ear. (Please refer to Fig.2, Fig3, Fig4, and

Fig.5)

Fig.1 Fig.2 Fig.3 Fig.4 Fig.5

2.Charging the battery:

(1)The Plug the travel charger into the AC outlet and then connect the charger

into the DC input of the headset. The red indicator of the

headset will light on. When the battery is full, the red

indicator will be off. Disconnect the adaptor from the headset.

When the battery is new, it is not fully charged. It takes nearly

4 hours to fully charge the battery. Afterwards, it will take

nearly 2 hours to fully charge the battery.

(2)If there is a USB charging cable included (optional), you

can charge the headset with the USB charging cable. Please

plug one end of USB charging cable to USB slot of your Fig.6

computer, another end to DC input of the headset. The following

is the same with the travel charger.

(Please refer to Fig.6.)

3.Turning the headset on or off:

(1)Press the “Button 1” for nearly 3 seconds.

You will hear two beep sounds and the blue

indicator will begin to flash. The headset is now

powered on.

(2)When the power is on, press the “Button 1”

for 3 seconds. You will hear two beep sounds

and the red indicator will flash. Now the

headset is turned off. (Please refer to Fig.7 and

Fig.8.) Fig.7 Fig.8

Summary of content (4 pages)

PAGE 1
User’s Guide 1.Assemble and disassemble the ear-hook with the Headset (1)To assemble the ear-hook with the Headset, push the toggle of the ear-phone into the pin-hole of the ear-hook. To disassemble the ear-hook with the Headset, just turn and pull out the toggle of the ear-phone from the pin-hole of the ear-hook. (Please refer to Fig.1) (2)Fit the ear-hook with your right or left ear. (Please refer to Fig.2, Fig3, Fig4, and Fig.5) Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 2.
PAGE 2
4.Pairing the headset: (1)The headset must be powered off before you begin to initiate the pairing. Press the “Button 1” till the blue and red indicators begin to flash alternatively. The headset is now in pairing mode. (2)Initiate the pairing process of your bluetooth mobile phone. (Please refer to the manual of your mobile phone.) (3)When asked the PIN code, please enter “0000” to successfully complete the pairing process.
PAGE 3
(The availability of this function depends on the design of the mobile phone you use. Please refer to the manual of your mobile phone.) 9.Mute function: You may have to keep a call on line while talking to others. Push the “Button 2” and the “Button 3” at the same time for one second. You will hear continuous beep sounds. Now the headset is in “Mute function” mode. To disable the “Mute function”, press the “Button 2 ” and the “Button 3” at the same time once again. 10.
PAGE 4
Safety instructions: 1.Check local laws about the use of mobile phone and headset while driving. For your own safety, please focus on the road while using the headset. 2.Please turn off the headset according to the sign of the specified areas that requires an electric device to be switch off. These areas include the hospital, aircraft, and blasting area or potentially explosive atmosphere. 3.Do not store the headset in the air-bag deployment area. This may result in an injury when the air-bag deploys. 4.