Owners manual

I.D. of lower Link inner pos. (control arm) is Ø1.563”. Using a
hydraulic press, properly support control arm and slowly
push out the rubber bushing with bonded outer metal shell.
O.D. Smaller
than Ø1.563”
I.D. Larger
than Ø1.563”
5
Installation instructions
For set # 7.3121
Front Control Arm Bushing Set
02-09 Nissan 350Z
03-07 Infiniti G35 Coupe RWD
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 8/JAN/03 BRH Updated 23/JAN/04 BRH
Updated 14/JAN/05 BRH Updated 10/JAN/06 BRH
Updated 2/JAN/07 BRH
2015 Energy Suspension. All rights reserved.
C
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Parts list:
2 - 2824 Front Upper Link (Control Arm) Rear Position
2 - 2825 Front Upper Link (Control Arm) Front Position
4 - 15.10.279.39 Upper Link (Control Arm) Sleeve
4 - 2826 Lower Link (Control Arm) Inner Position
2 - 15.10.617.39 Lower Link (Control Arm) Inner Sleeve
2 - 08P08399 Lower Link Strut Position, Inner
2 - 08P08400 Lower Link (Control Arm) Strut Position, Outer
2 - 15.10.525.39 Lower Link (Control Arm) Strut Sleeve
4 - 2829 Compression rod (Radius Arm)
2 - 15.10.616.39 Compression rod (Radius Arm) Sleeve
(Control Arm)
PG 1 OF 2
Important - Please READ: It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this
type of work. It is also recommended that if you choose to do this work yourself that a factory service manual be obtained for the proper procedures pertaining
to component removal, replacement and proper torque specifications for your vehicle. This instruction set is intended as a guideline for the safe installation of
Energy Suspension's polyurethane bushings, once you have removed the factory components from your vehicle. Wheel alignment is almost always disturbed
when suspension components are removed or replaced. It is recommended that you have the alignment checked on your vehicle at a qualified alignment
shop. Prior to installation, make sure that your vehicle is in top mechanical condition and that there are no suspension or steering related problems. These
components have been designed to work only with a vehicle that is in good state of repair. No matter how carefully we design our parts, this is one area we
have no control over and cannot be held responsible. The installation of these components may void the factory warranty for your vehicle. Please contact your
local dealership for details concerning the factory warranty before installation. Energy Suspension recommends that you thoroughly read over all the
installation instructions and check all P/N's and quantities in the Parts List before you start. Call customer service at 949-361-3935 if the parts in your kit do
not match this Parts List.
Apply grease to all metal parts that contact the polyurethane
bushing part numbers 2829 & inner metal sleeve
15.10.616.39 before pressing into the control arm.
Bushings
2829
sleeve
15.10.616.39
4
I.D. of front Upper Link (control arm) is Ø1.198”. Using a
hydraulic press, properly support control arm and slowly
push out the rubber bushing with bonded outer metal shell.
I.D. Larger
than Ø1.198”
O.D. Smaller
than Ø1.198”
1
Bushings
2824 & 2825
sleeve
15.10.279.39
Apply grease to all metal parts that contact the polyurethane
bushing part numbers 2824, 2825 & inner metal sleeve
15.10.279.39 before pressing into the control arm.
2
I.D. of Compression Rod (radius arm) is Ø2.350”. Using a
hydraulic press, properly support control arm and slowly
push out the rubber bushing with bonded outer metal shell.
I.D. Larger
than Ø2.350”
O.D. Smaller
than Ø2.350”
3
17555 BRH 10/SEP/2015 ECN 15100