User Guide

ManualsBrandsENERLITES ManualsIndustrial & ScientificMPC-50V-STICKER Ceiling Occupancy Sensor by PIR Ceiling Sensor for Junction Box Installation, MPC-50V, White

Figure 1

Testing & Code Compliance



UL LISTE D

Motor..............................................................................1/4 HP ,120VAC, 60HZ

Incandescent....................................................................800W-120VAC, 60HZ

Operating Temperature ...................................................32°to 131°F (0°to 55°C)

Adjustable Light Level ................................................................10FC—150FC

Adjustable Time Delay ................................................................15 sec.-30min

Sensitivity Adjustment.........................................50% or 100% (DIP switch 1)

Coverage……………………...................……………………………Up to 1200 ft

Fluorescent ...................................800VA-120VAC / 1600VA-277VAC, 60HZ

Resistive ..........................................................................800W-120VAC, 60HZ

The MPC-50V provides a 360° coverage pattern, up to 1200 square feet. The

coverage shown represents walking motion at a mounting height of 8 feet(See

Figure 1 ).For building spaces with lower levels of activity or with obstacles

and barriers, coverage size may decrease.

44 ft

13.4m

8 ft

22 ft 22 ft13 ft 13 ft7 ft 7 ft3 ft 0 3 ft

Typical

desk-top

level

Coverage Pattern

Description: The MPC-50V 360 °passive infrared (PIR) occupancy sensors turn lighting systems

on and off based on occupancy and ambient light levels. The light level feature keeps lights from

turning on if the ambient light level is sufficient. The sensors can be configured to turn lighting on,

and hold it on as long as the sensor detects occupancy. After no movement is detected for a

specified time the lights are switched off.

360° Passive Infrared

ine Voltage Occupancy Sensor

Model #: MPC-50V

General

Specification

 Passive Infrared

Technology(PIR)

 360 ° field of view, 1200sqft

 Time Delay is adjustable

from 5 seconds to 30

minutes

 Simple, fast installation

 Adjustable sensitivity

settings

 Light level is adjustable.

Specifications

Features

Summary of content (4 pages)

PAGE 1
General Specification 360° Passive Infrared Line Voltage Occupancy Sensor Model #: MPC-50V Description: The MPC-50V 360 °passive infrared (PIR) occupancy sensors turn lighting systems on and off based on occupancy and ambient light levels. The light level feature keeps lights from turning on if the ambient light level is sufficient. The sensors can be configured to turn lighting on, and hold it on as long as the sensor detects occupancy.
PAGE 2
Wiring Directions WARNING: Turn off the power at the circuit breaker before installing Refer to the wire diagram of the sensor (see figure 2), and connect the wires of ceiling sensors as followed by using the wire nuts provided.1. Connect the Hot wire of main power to the Black wire from the sensor.2. Connect the Load wire to the Red wire from the sensor.3. Connect the Neutral wire of Load and main power to the White wire from the sensor.4.
PAGE 3
Sensor Adj ustment Keyhole slots(for mounting to 4" octagonal box) 10 Min TEST 20 Min PIR lens PIR Activity LED(Red) 30 Min Time Delay Adjustment + Light Light level Adjustment Figure 4 Double gang mudring mounting holes DIP switches Note: There is a 40- second warm-up period when power is first applied. The sensors are factory preset to allow for quick installation in most applications.
PAGE 4
DIP Switch Setting The MPC-50V has 2 DIP switches under the cover. They are used to set sensitivity, vacancy mode feature settings. Sensitivity 50% 100% =OFF Vacancy Enabled Disabled 1 =ON 2 =Factory Setting Sensitivity setting: DIP Switch 1 1. 50% , sensor’s coverage is smaller, just about half of the widest range. 2.