INDEX Precaution Notice ............................................................................................ 1 ENERMAX PRO87+ series Power Supply Specification.............................. 2 ENGLISH........................................................................................................ 3 DEUTSCH ...................................................................................................... 7 ESPAÑOL .............................................................................
Precaution Notice Only a technician, authorized by ENERMAX, is allowed to perform maintenance service! Warranty is subject to void under unauthorized attempt to open the power case or modification of any kinds, even attempted only, of the power supply or its components! ENERMAX will not be responsible for damages caused by following situations: Opening of the PSU case and/or modification of any component or cable without ENERMAX’ written authorization.
ENERMAX PRO87+ Series Power Supply Specification EPG500AWT EPG600AWT EPG700AWT 100-240VAC, 50-60Hz (Maximum range:90-265VAC, 47-63Hz) 6.5 – 3A 8 – 3.5A 9 – 4A AC Input Voltage AC Input Current DC Output Rated 3.3V 5V 12V1 12V2 12V3 -12V 5Vsb Total Power Peak Power Combined 0-20A 0-20A 0-25A 0-25A 0-25A 0-0.5A 0-3A 100W 492W (41A) 6W 15W 500W 550W Rated 0-24A 0-24A 0-25A 0-25A 0-25A 0-0.5A 0-3A Combined 120W 600W (50A) 6W 15W 600W 660W Rated 0-24A 0-24A 0-25A 0-25A 0-25A 0-0.
User’s Manual Dear customer, Thank you for choosing this ENERMAX PRO87+ power supply unit (PSU)! Please read this manual carefully and follow its instructions before installing the PSU. We would like to draw your attention that a computer required very specific conditions to work best for you without failing. To avoid failures and to increase lifetime of the system, we suggest that: Your system is NOT located near a radiator or any other heat producing device.
NAME OF PARTS 1Output cable: Please check “Cables & Connectors” section. 2 13.9cm fan.# 1 3 Honeycomb air vent. # 1 4 ON/OFF switch: (I=ON, O=OFF). # 2 5 AC Inlet. # 2 6 CordGuard. # 3 #1 To ensure best system cooling, do not block PSU fan’s air in-take and air vent area. This PSU offers a special HeatGuard function. When the system is turned off, or goes into ACPI S3/S4 sleep mode, the PSU fan will keep dissipating the remaining heat for 30 ~ 60 seconds and prolonging system lifetime.
CONNECTOR TYPES 24P Mainboard For new generations of ATX/EEB/CEB server/workstation MB. 8P CPU +12V (700W) Supports multi-CPU server/workstation systems and some single socket systems. 4+4P (8P) CPU +12V, in combined mode 8-pin configuration supports multi-CPU server/workstation systems and some single extreme CPU systems. 4+4P (8P) CPU +12V, in split mode 4-pin configuration supports certain single CPU systems. Some multi-CPU workstation/server system might also need this extra 4-pin 12V connector.
BOOTING YOUR SYSTEM Before booting your system, please check that: 1. Main power connector (24P) is properly connected. 2. CPU +12V power connector (4 or 8-pin configuration), and/or a 4P Molex connector (if required by MB) is properly connected. 3. All other needed connectors are properly connected. 4. AC cord is properly connected to wall outlet and PSU AC inlet. 5. Close your system chassis. 6. Turn on the PSU by switching the ON/OFF switch to “ON”, and your system is ready.
Benutzerhandbuch Sehr geehrte Kundin, sehr geehrter Kunde, Vielen Dank, dass Sie sich für dieses ENERMAX PRO87+-Netzteil (PSU) entschieden haben! Bitte lesen Sie sich dieses Handbuch sorgfältig durch und folgen Sie bitte seinen Anweisungen bevor Sie das Netzteil installieren! Wir möchten Sie darauf hinweisen, dass moderne Systeme sehr empfindlich geworden sind und genau definierte Bedingungen benötigen, um optimal ohne Ausfälle arbeiten zu können.
DETAILBESCHREIBUNG ①Ausgangskabel: Bitte lesen Sie den Abschnitt „Kabel & Anschlüsse“. ②13.9cm Lüfter. #1 ③Honigwabenluftauslass. #1 ④I/O Schalter: separater NetzteilAn/Aus-Schalter (I=AN, O=AUS). #2 ⑤Stromeingang. #2 ⑥CordGuard. #3 #1 Bitte blockieren Sie nicht die Lufteinlässe/Luftauslässe, um eine bestmögliche Systemkühlung zu gewährleisten.
Anschlusstypen 24P Mainboard Für die neueste Generation von ATX/EEB/CEB Server/Workstation MB’s. 8P CPU +12V (700W) Unterstützt Multi-CPU Server/Workstation-Systeme und einige Ein-Sockel-Systeme. 4+4P (8P) CPU +12V, in “kombiniertem Modus” Unterstützt Multi-CPU Server/Workstation-Systeme und einige Hochleistungs-Einzel-CPU-Systeme. 4+4P (8P) CPU +12V, in “getrenntem Modus” 4-Pin Konfiguration unterstützt herkömmliche Einzel-CPU-Systeme.
EINSCHALTEN IHRES SYSTEMS Vor dem Einschalten Ihres Systems stellen Sie bitte sicher, dass: 1. Mainboard-Stromanschluss (24P) korrekt angeschlossen ist. 2. CPU +12V ATX Stromanschluss (4 oder 8 Pin Konfiguration) (falls für MB erforderlich) korrekt angeschlossen ist, oder ein 4-Pin Molex-Stromanschluss (falls für MB erforderlich) korrekt angeschlossen ist. 3. Alle anderen erforderlichen Stromanschlüsse korrekt angeschlossen sind. 4.
Manual Del Usuario Estimado cliente: Muchas gracias por comprar nuestra fuente ENERMAX PRO87+. Le recomendamos que se lea bien este manual para el usuario. Queremos recordarle que los ordenadores actuales son muy vulnerables y necesitan condiciones especiales para funcionar sin problemas. Para evitar dichos fallos y maximizar la duración del sistema, le recomendamos que se asegure de: Su ordenador no se encuentre al lado de la calefacción ni otro objeto que irradie calor.
NOMENCLATURA DE LAS PARTES ①Cable del corriente: Por favor, examine el párrafo „CABLES Y ENCHUFES”. ②Ventilador de 13.5 cm.# 1 ③Honeycomb air vent. # 1 ④Interruptor I/O*: separado interruptor de la fuente por En/Paro (I=En, O=Paro). # 2 ⑤Toma de corriente # 2 ⑥CordGuard # 3 #1 Para asegurar la mejor refrigeración del sistema., no obstruya la ventilación de la fuente. Esta fuente le ofrece una función especial “HeatGuard”.
TIPOS DE ENCHUFES 24P placas base Soporta generaciones nuevas de ATX/EEB/CEB server/workstation. 8P CPU +12V (700W) Soporta multi-CPU server/workstation y algunos sistemas single-socket. 4+4P CPU +12V, en “modo combinado” La configuración 8-Pin soporta multi-CPU server/workstation y algunos sistemas single-socket extremas. 4+4P CPU +12V, en “modo separado” La configuración 4-Pin soporta la mayoría de los sistemas single-socket.
ENCENDIENDO EL SISTEMA Antes de encenderlo por favor asegúrese de que: 1. El enchufe de la placa base está conectado correctamente. 2. El enchufe de la CPU +12V AUX (si es necesario) esté conectado correctamente. o un enchufe 4-Pin Molex (si es necesario) esté conectado correctamente. 3. Todos los otros enchufes necesarios están conectado correctamente. 4. El cable de la corriente (AC) está conectado correctamente con la fuente y el enchufe! 5. Cierre la caja del sistema! 6.
Manuel d’utilisateur Chers clients, Merci d’avoir choisi l’alimentation ENERMAX PRO87+! Veuillez lire avec attention ce manuel avant de procéder à l’installation de l’alimentation. Nous souhaiterions attirer votre attention sur le fait qu’un ordinateur est fragile et demande de respecter certaines conditions pour fonctionner de façon optimale.
ELEMENTS PRATIQUES 1Câble de sortie: Veuillez consulter la section ‘‘Câbles & Connecteurs’’. 2 Ventilateur de 13.9cm.# 1 3 Ventilation en Nid d’abeille. # 1 4 Bouton ON/OFF: (I=ON, O=OFF). # 2 5 Connecteur AC. # 2 6 CordGuard. # 3 #1 Pour assurer un refroidissement optimal de votre système, veillez à ne pas obstruer les entrées et sorties d’air de l’alimentation. Cette alimentation intègre la fonction HeatGuard.
CONNECTOR TYPES 24P Carte Mère Pour la nouvelle génération de cartes mères serveur et stations de travail ATX/EEB/CEB. 8P CPU +12V (700W) Pour les serveurs et stations de travail multi-CPU et certaines mono CPU. 4+4P (8P) CPU +12V, en mode combiné La configuration 8-pins supporte les serveurs et stations de travail multi-CPU et certaines mono CPU. 4+4P (8P) CPU +12V, en mode séparé La configuration 4-pins supporte les systèmes mono CPU.
DEMARRER VOTRE SYSTEME Avant de démarrer votre système, veuillez vérifier les points suivants: 1. Le connecteur d’alimentation principal est correctement branché (24P). 2. Le connecteur CPU +12V (4P ou 8P), et/ou le connecteur 4P Molex (si nécessaire) sont correctement branchés. 3. Tous les autres connecteurs nécessaires sont correctement branchés. 4. Le cordon d’alimentation doit être connecté à la prise électrique murale et à l’alimentation. 5. Fermer le boîtier de votre système. 6.
Manuale dell’Utente Cari clienti, Vi siamo grati per avere scelto questo ALIMENTATORE ENERMAX PRO87+ ! Prima di installarlo, leggete attentamente questo manuale e seguite le sue istruzioni. Desideriamo richiamare la vostra attenzione sul fatto che un computer richiede condizioni di lavoro molto specifiche per dare il meglio in termini di prestazioni, e non guastarsi. Onde evitare guasti e aumentare la durata del sistema, vi consigliamo: Di NON posizionare il sistema vicino a fonti di calore.
COMPONENTI ①Cavo di output: Consultare la sezione “Cavi e connettori”. ②Ventola da 13.5cm.# 1 ③Condotto espulsione aria calda (struttura a nido d’ape).# 1 ④Interruttore ON/OFF: (I=ON, O=OFF).# 2 ⑤Entrata AC. # 2 ⑥CordGuard.
TIPI DI CONNETTORI Scheda madre 24P Per le nuove generazioni di MB : ATX/EEB/CEB. 8P CPU +12V (700W) Per sistemi server/workstation multi-CPU o sistemi a CPU singola. 4+4P (8P) CPU +12V, in modalità combinata Per server/workstation multi-CPU o sistemi a CPU singola. 4+4P (8P) CPU +12V, in modalità separata Per server/workstation multi-CPU o sistemi a CPU singola . Usare il connettore con il segno “12V”.
ACCENSIONE DEL SISTEMA Prima di accendere il sistema controllare che: 1. Il connettore principale (24 pin) sia adeguatamente collegato. 2. Il connettore CPU +12V (configurazione 4 o 8 pin), e/o un connettore Molex 4P (se richiesto da MB) sia adeguatamente collegato. 3. Tutti gli altri connettori necessari siano adeguatamente collegati. 4. Il cavo AC sia adeguatamente collegato alla presa a muro e alla presa di entrata AC del PSU. 5. Chiudere il Case, prima di fornire tensione. 6.
Руководство пользователя Уважаемый пользователь, Спасибо за то, что выбрали блок питания (БП) ENERMAX PRO87+. Перед установкой БП внимательно прочтите данное руководство и придерживайтесь изложенных в нем указаний. Обратите внимание на то, что для бесперебойной работы компьютера требуется соблюдение специфических условий. Во избежание сбоев в работе и продления срока службы системы мы рекомендуем: НЕ устанавливать систему возле батареи или другого теплогенерирующего устройства.
НАЗВАНИЯ ЧАСТЕЙ ①Кабель вывода: См. раздел «Кабели и подключения». ②13,5 см вентилятор. # 1 ③Ячеистая структура вентиляционного отверстия. # 1 ④Переключатель «Вкл./Выкл.»: (I=ВКЛ., O=ВЫКЛ.). # 2 ⑤Силовой разъем переменного тока. # 2 ⑥CordGuard. # 3 #1 Для обеспечения наилучшего охлаждения системы, не закрывайте доступ к воздухозаборному и вентиляционному отверстию вентилятора PSU. PSU обладает специальной функцией HeatGuard.
ВИДЫ ПОДКЛЮЧЕНИЙ 24-контактное подключение материнской платы Для нового поколения материнских плат серверов/рабочих станций ATX/EEB/CEB. 8-контактный разъем CPU +12В (700W) Поддерживает мульти-CPU сервера/рабочие станции и некоторые одноразъемные системы. 4+4-контактный (8P) CPU +12В комбинированный разъем 8-контактная конфигурация поддерживает сервера/рабочие станции с множественными CPU и некоторые системы с одним CPU нового поколения.
ЗАГРУЗКА СИСТЕМЫ 1. Главный разъем питания правильно подключен (24-контактная конфигурация). 2. Разъем питания ЦП +12В (4- или 8-контактная конфигурация) и (или) 4-контактный Molex-разъем (если требуется для материнской платы) правильно подключены. 3. Все остальные необходимые разъемы правильно подключены. 4. Кабель питания переменного тока надлежащим образом подключен к электрической розетке и входному гнезду переменного тока БП. 5. Корпус ПК закрыт. 6. Включите БП, установив переключатель «Вкл./Выкл.
Instrukcja obsługi Szanowni Klienci, Dziękujemy za zakup tego zasilacza ENERMAX PRO87+ (PSU)! Proszę przeczytać uważnie ten podręcznik i wykonać zamieszczone w nim instrukcje przed instalacją zasilacza. Chcielibyśmy zwrócić Państwa uwagę na fakt, że komputer wymaga pracy w bardzo specyficznych warunkach. Aby uniknąć awarii i wydłużyć żywotność systemu zalecamy, aby: NIE umieszczać systemu w pobliżu grzejnika lub innych urządzeń wytwarzających ciepło.
NAZWA CZĘŚCI ①Kabel wyjścia: Sprawdź część „Kable i połączenia”. ②Wentylator 13,5cm.# 1 ③Szczeliny wentylacyjne „plaster miodu”. # 1 ④Przełącznik Włączenie/Wyłączenie: (I=Włączenie, O=Wyłączenie). # 2 ⑤Wejście prądu zmiennego. # 2 ⑥CordGuard. # 3 #1 Aby zapewnić optymalne chłodzenie systemu, nie należy blokować wlotu powietrza wentylatora PSU i szczelin wentylacyjnych. Ten PSU oferuje specjalną funkcję HeatGuard.
RODZAJE ZŁĄCZY 24-pinowe złącze płyty głównej Do nowej generacji płyt głównych serwera/stacji roboczych ATX/EEB/CEB. 8-pinowe CPU +12V (700W) Obsługa wielo procesorowych systemów serwera/stacji roboczych i niektórych systemów z gniazdem pojedynczym. CPU 4+4-pinowe (8-pinowe) +12V, w trybie kombinowanym 8-pinowa konfiguracja obsługuje wielo procesorowych systemów serwera/stacji roboczych i niektóre pojedyncze, ekstremalne rozwiązania systemów CPU.
URUCHAMIANIE SYSTEMU Przed uruchomieniem systemu należy sprawdzić, czy: 1. Jest prawidłowo podłączone złącze zasilania (24-pinowe). 2. Czy jest prawidłowo podłączone złącze zasilania CPU +12V (konfiguracja 4- lub 8-pinowa) i/lub złącze 4-pinowe Molex (jeśli jest wymagane przez płytę główną). 3. Czy są prawidłowo podłączone wszystkie inne wymagane złącza. 4. Czy przewód zasilający prądu zmiennego jest prawidłowo podłączony do gniazda ściennego i do gniazda wejścia prądu zmiennego zasilacza. 5.