Owner`s manual

1.6.
1.6.1.6.
1.6. VENTING
VENTINGVENTING
VENTING
In Canada, we recommend that you use a listed pellet vent that meets the ULC S-609-M89/ORD C441-M90 Standard.
For the United States, we recommend that you use a listed pellet vent that meets the UL-641Standard.
This unit can be vented in an existing factory-built or masonry chimney with the addition of a liner, provided the chimney
is more than 4” in diameter. The liner should be listed and should meet the ULC S-635/640 standard in Canada and the UL-
1777 standard in the USA. Refer to the instructions provided by the vent or chimney manufacturer, especially when passing
through a wall, ceiling, or roof.
Your venting system should have at least one foot of vertical rise for each foot of horizontal run. Th
Your venting system should have at least one foot of vertical rise for each foot of horizontal run. ThYour venting system should have at least one foot of vertical rise for each foot of horizontal run. Th
Your venting system should have at least one foot of vertical rise for each foot of horizontal run. The total vertical rise
e total vertical rise e total vertical rise
e total vertical rise
should never be less than 3 feet (see Appendix A).
should never be less than 3 feet (see Appendix A).should never be less than 3 feet (see Appendix A).
should never be less than 3 feet (see Appendix A).
This unit uses a pressurized exhaust system. All vent connector joints must be sealed and fastened. If vented horizontally,
joints should be made gastight. Please consult the pellet pipe manufacturer’s instruction to ensure proper installation
and consistent performance to avoid smoke and ash spillage.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT INSTALL A FLUE DAMPER IN
DO NOT INSTALL A FLUE DAMPER IN DO NOT INSTALL A FLUE DAMPER IN
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
THE EXHAUST VENTING SYSTEM OF THIS UNIT.THE EXHAUST VENTING SYSTEM OF THIS UNIT.
THE EXHAUST VENTING SYSTEM OF THIS UNIT.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
WARNING :
WARNING :WARNING :
WARNING : DO NOT INSTALL IN SLEEPING ROOM
DO NOT INSTALL IN SLEEPING ROOMDO NOT INSTALL IN SLEEPING ROOM
DO NOT INSTALL IN SLEEPING ROOM
CAUTION :
CAUTION :CAUTION :
CAUTION : THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND
THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND
THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINT
CEILING/ROOF MUST BE MAINTCEILING/ROOF MUST BE MAINT
CEILING/ROOF MUST BE MAINTAINED
AINEDAINED
AINED
CAUTION :
CAUTION :CAUTION :
CAUTION : THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED
THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED
THE CHIMNEY CONNECTOR SHALL NOT PASS TROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED
SPACE
SPACESPACE
SPACES, OR
S, ORS, OR
S, OR FLOOR
FLOORFLOOR
FLOORS
SS
S, OR CEILING
, OR CEILING, OR CEILING
, OR CEILINGS
SS
S.
..
.
1.6.1.
1.6.1.1.6.1.
1.6.1.
Equivalent Vent Length (EVL)
Equivalent Vent Length (EVL)Equivalent Vent Length (EVL)
Equivalent Vent Length (EVL)
The longer the run of pipe in your installation, the greater
the restriction in your system.
• Always use 4” pipe
• Horizontal runs shall not exceed 30 feet of EVL.
To calculate EVL, use the following conversions table:
Qty
QtyQty
Qty
Type of pipe
Type of pipeType of pipe
Type of pipe
EVL equivalent(ft)
EVL equivalent(ft)EVL equivalent(ft)
EVL equivalent(ft)
1
90° elbow or “T”
5
1
45° elbow
3
1 ft
Horizontal pipe run
1
1 ft
Vertical
pipe run
0.5
Here is an example on how to calculate the EVL of your
installation. (See Figure 10):
(3 x 4’ of vertical length = 12’ x 0.5 = 6 EVL) +
(1 x elbow or "T" = 5 EVL) +
(2 x 1’ of horizontal length = 2 EVL)
Total EVL = (6 + 5 +2) = 13.
1.6.2.
1.6.2.1.6.2.
1.6.2. Installation Configurations
Installation ConfigurationsInstallation Configurations
Installation Configurations
FIGURE 10
Venting through wall