Product Manual

ManualsBrandsEngel ManualsFreezerSB47F

Table Of Contents

NH3 L

MODEL

INPUT

SB47F

DC12/24V

SR48F

SR90F

AC22OV-240V,DC1 2/24V

ST90F

ST68F

SR70F

CAUTIONS:

Never store gasoline or other namable vapors and liquids

as these sometimes cause explosion.

Do not touch evaporator and metal parts of cabinet inside

by wet hand. Sometimes, it cause frostbite to your hand.

Do not remove or modify all the electrical live parts to

avoide electric shock and trouble of your refrigerator.

If the supply cord is damaged, it must be replaced by

the manufactureror its service agent or a similarly gualified

person in order to avoid a hazard.

Suitable for camping use ;

The appliance shall not be exposed to rain.

ST9OF-G4

MODEL



JPT 006C

SERIAL NO.



SAWAFUJI ELECTRIC CO.,LTD.

(Cat. No. 5490 349 1000)

Printed in Japan

Summary of content (9 pages)

PAGE 1
CAUTIONS: NH3 L MODEL SB47F SR48F SR90F ST90F ST68F SR70F INPUT DC12/24V 1. Never store gasoline or other namable vapors and liquids as these sometimes cause explosion. 2. Do not touch evaporator and metal parts of cabinet inside by wet hand. Sometimes, it cause frostbite to your hand. 3. Do not remove or modify all the electrical live parts to avoide electric shock and trouble of your refrigerator. 4.
PAGE 2
Connect the DC power supply Remove the two (2) screws that attach the junction cover. Remove the junction cover. Put the code set through the bushing of the junction cover. 6 Fig. 1 5 ❑ Electrical equipment O Battery 0 Refrigerator ❑ Cables twisted together © INCORRECT ® CORRECT - Push the DC input wires onto the DC input terminals. - Refer to the positive (+) and negative (-) markings to make sure that the connections are correct. - Attach the junction cover with the two (2) screws.
PAGE 3
INSTRUCTIONS FOR USE 0 Current Sources. 1.1. Connection to 220v-240v,50Hz AC Mains. (Except MODEL SB47F) Your Engel refrigerator may be connected to a standard domestic mains power source, using the three-core mains lead provided. Set the thermostat control knob to "0 (OFF) until the current has been turned on. Then, set the thermostat control knob to 1 -5" aand the green lamp will light up. Turn the thermostat control knob to the required setting. 1.2. Connection to 12 24V DC Batteries.
PAGE 4
❑ Cleaning. ALWAYS DISCONNECT THE ELECTRIC CURRENT SUPPLY BEFORE CLEANING. SWITCHING OFF IS NOT ENOUGH-PULL OUT THE PLUG! Remove from the cabinet all water resulting from defrosting, because this otherwise will become the cause of unpleasant odor and taintting affecting the refrigerator contents. Wipe the cabinet interior clean with a damp cloth wrung out in warm water containing a mild, non-abrasive household detergent.
PAGE 5
SB47F / SR48F / SR70F VENTING Sufficient ventilation (airflow) over the rear mounted condenser of the refrigerator is necessary for the refrigerator to operate correctly . How to replace door panne) NOTE: The decorative door panel must be 4 mm or less in thickness. * NOTE: The fan will operate only when the ambient temperature is higher than approximately 95° F. 1. Remove the door from the refrigerator by removing the two (2) bolts that attach the door hinge to the bottom of the refrigerator.
PAGE 6
. Move the latch to the opposite side of the door. T Screw - Remove the screw that attaches the hinge insert to the door. Remove the hinge insert, the latch handle, and the coil spring from the door. - Pull the latch handle pin out of the recess in the latch handle. - Move the latch handle in to opposite side of the latch pin . - Turn the latch handle upside down and push the latch handle pin into the recess of the latch handle. ventilation Dj 510.
PAGE 7
ST68F / ST90F / SR90F HOW TO REPLACE DOOR PANNEL ST68F HOW TO CHANGE DOOR OPENING DIRECTION 1Remove 2 hinge plates (both upper and lower side) and door stopper by pulling out of 6 1. Remove door from refrigerator. screws. (Remove hinge pin by use of screw driver.) Upper hinge plate Hinge pin Door stopper Lower hinge plate 2. Remove lower pannel frame. 2. Fix the hinge plates at counter side of cabinet end. Lower pannel frame 3. Pullout screw of door stopper plate and remove door stopper holder.
PAGE 8
III VENTING ST90F SR90F ST68F Model In order to assure efficient operation an adequate airflow over the rear mounted condenser of utrymmefor Dj 548 Dj 548 Dj 548 ventilation Br 455 Br 525 Br 525 H 547 H 750 H 780 the refrigerator is required. Please refer to the illustration showing the various approved venting arrangements. Venting should be installed using any of the following combinations for truck use.
PAGE 9
ST90F / SR90F 1. Remove the 2 hinge plates (both upper and lower side) door stopper plate and stopper pin, and lower hinge plate (Door support) by loosen of 8 screws. 2. Fix the hinge plates, the door stopper and stopper pin and lower hinge plate (Door support) as counter side of cabinet end.