ECB-1220R Wireless Client Bridge /AP/Router/Client Router User’s Manual Version: 1.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Table of Contents 1 INTRODUCTION .................................................................................................................... 5 FEATURES & BENEFITS .................................................................................................................. 5 PACKAGE CONTENTS .....................................................................................................................
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater 4 Version 1.1 CLIENT BRIDGE/ROUTER MODE – CONFIG.................................................................... 46 LOGGING IN ................................................................................................................................. 46 MANAGEMENT ............................................................................................................................. 48 OPERATION MODE ................................
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Revision History Version Date Notes 1.0 1.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 1 Introduction The Wireless Client Bridge/AP/Router/Bridge Router device operates seamlessly in the 2.4 GHz frequency spectrum supporting the 802.11b (2.4GHz, 11Mbps) and faster 802.11g (2.4GHz, 54Mbps) wireless standards. It's the best way to add wireless capability to your existing wired network, or to add bandwidth to your wireless installation. ECB-1220R has high transmitted output power and high receivable sensitivity.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 SNMP Remote Configuration Help administrators to remotely Management configure or manage the Access Point easily.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater User isolation support Version 1.1 Protect the private network between client users. Client Router mode PPPoE function support Easy to access internet via ISP service authentication Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, in case of return; the unit must be shipped in its original package.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 System Requirements The following are the minimum system requirements in order configure the device. h PC/AT compatible computer with Ethernet interface. h Operating system that supports HTTP web-browser Applications The wireless LAN products are easy to install and highly efficient.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 network. f) Wireless extensions to Ethernet networks Network managers in dynamic environments can minimize the overhead caused by moves, extensions to networks, and other changes with wireless LANs. g) Wired LAN backup Network managers implement wireless LANs to provide backup for mission-critical applications running on wired networks.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 b) Infrastructure Mode The infrastructure mode requires the use of an access point (AP). In this mode, all wireless communication between two computers has to be via the AP. It doesn’t matter if the AP is stand-alone or wired to an Ethernet network. If used in stand-alone, the AP can extend the range of independent wireless LANs by acting as a repeater, which effectively doubles the distance between wireless stations.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 2 Understanding the Hardware Hardware Installation 1 Place the unit in an appropriate place after conducting a site survey. 2 Plug one end of the Ethernet cable into the RJ-45 port of the device and another end into your PC/Notebook. 3 Insert the DC-inlet of the power adapter into the port labeled “DC-IN” and the other end into the power socket on the wall.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 2. Select Internet Protocol (TCP/IP) and then click on the Properties button. This will allow you to configure the TCP/IP settings of your PC/Notebook. 3. Select Use the following IP Address radio button and then enter the IP address and subnet mask. Ensure that the IP address and subnet mask are on the same subnet as the device. For Example: Device IP address: 192.168.1.1 PC IP address: 192.168.1.10 PC subnet mask: 255.255.255.0 4.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 3 Client Bridge/Router & Router/ AP This device can be configured as a Bridge or Access Point. The default IP address of the device is 192.168.1.1 in Client Bridge/Client Router mode. The default IP address of the device is 192.168.1.2 in AP/Router mode. This chapter will describe the steps to switch from Bridge to Access Point and Access Point to Bridge. Bridge/Bridge Router to Access Point 1 Enter the default IP address (192.168.1.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater 4 Version 1.1 Since this device is currently in Access Point mode, the AP radio button will be selected by default. 5 Select the Bridge or Bridge Router radio button to and then click on the Apply Change to switch the operation mode to Bridge. 6 Wait for about 1 minute and the device will automatically restart into Bridge mode.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 After logging in you will graphical user interface (GUI) of the bridge. The navigation drop-down menu on left is divided into three main sections: 1. Management: This includes operation mode, status, statistics, logs, upgrade firmware, save/reload settings, and password. 2. TCP/IP Settings: This includes the configuration of the LAN port and settings for the LAN IP, subnet mask, DHCP client, spanning tree and MAC cloning. 3.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 o Mode: Wireless configuration mode such as Client Bridge, AP, or WDS. o Band: Frequency and IEEE 802.11 operation mode (b-only, g-only, or b+g). o SSID: The name used to identify the wireless network. o Channel Number: The channel used to communicate on the wireless network. o Encryption: The type of security used on this network. It may be disabled, WEP, WPA, etc. o BSSID: The MAC address of the SSID.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Management (Router mode) Operation Mode Click on the Operation Mode link under the Management menu. The Operation Mode allows you to switch from Client Bridge to Access Point mode/Router Mode.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Select the AP, Bridge or Bridge Router and then click on the Apply Change button. Please wait and then enter the specified IP address into the web-browser. The previous settings will be retained in AP mode. . Refer to Chapter 5 to learn how to configure this device in Access Point mode.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Status Click on the Status link under the Management menu. The Status page is the first page that is displayed once you have logged in. This includes details about the system, wireless, and TCP/IP configuration.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 System o Uptime: Duration of time since the device was last reset. o Firmware version: Version of the firmware that is currently loaded on the device. Wireless Configuration: o Mode: Wireless configuration mode such as Client Bridge, AP, or WDS. o Band: Frequency and IEEE 802.11 operation mode (b-only, g-only, or b+g). o SSID: The name used to identify the wireless network.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Additional WAN traffic information under Router Mode Since the packet counter is not dynamic, you must click on the Refresh button for the most recent statistics. Dynamic DNS (Router mode) Allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater • Version 1.1 Timeout: Specify the time between periodic updates to the Dynamic DNS, if the dynamic IP address has not changed. The timeout period is entered in hours. • Click on the Save Settings button once you have modified the settings. Time Zone Setting (Router mode) Click on the Time link in the navigation menu.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Current Time: Displays the current time on the device. Time Zone: Select your time zone from the drop-down list. Enable NTP Server: Place a check in this box if you would like to synchronize the device’s clock to a Network Time Server over the Internet. If you are using schedules or logs, this is the best way to ensure that the schedules and logs are kept accurate.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 referred when an unknown error occurs on the system or when a report needs to be sent to the technical support department for debugging purposes. In order for the log to record all the events, you must first place a check in the Enable Log or Enable Remote Log (Log Server required) check box. Select system all or wireless depending on the type of events you want recorded.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Click on the Browse button and then select the appropriate firmware and then click on the Upload button. Click on Reset to Default to restore the device to factory default settings. Note: The upgrade process may take about 1 minute to complete. Do not power off the device during this process as it may crash the device and make it unusable. The device will restart automatically once the upgrade is complete.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Click on the Save button to save the current settings to a file on the local disk. Click on the Browse button to select the settings file and then click on the Upload button to load the previously saved settings. Click on the Reset button to reset the device to its factory default settings. Click Restart to reboot the device. Password Click on the Password link under the Management menu.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 LAN Interface Click on the LAN Interface link under the TCP/IP Settings menu. Using this option you may change the IP address of the device as well as toggle the DHCP setting. IP Address: Enter the IP address. Subnet Mask: Enter the subnet mask for the IP address. Default Gateway: Enter the IP address for the default gateway.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Read-Only Community Name: Specify the password for access the SNMP community for read only access. Read-Write Community Name: Specify the password for access to the SNMP community with read/write access. Send SNMP Trap: Select Enable if you would like to receive SNMP traps. Send Trap To: Specify the IP address that would receive the SNMP traps. Trap Community Name: Specify the password for the SNMP trap community.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 (Router mode) Static IP Static IP is a fixed IP configuration where all parameters including DNS if any should explicitly configured. VPN pass through is configured here by defining exclusivity.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 (Router mode) PPPoE This type of connection is usually used for a DSL service and requires a username and password to connect.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 (Router mode) Username / Password & Connection type (PPPoE) should be input then click on the Connect button. Address Mode: PPPoE can be used with a dynamic or static IP address. If you select the Dynamic IP radio button, then the IIP address in the next field is not required. However, if you select the Static IP radio button, then the IP address in the next field is required.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 enter a username and password (provided by your ISP) to gain access to the Internet. The supported authentication protocols are PAP and CHAP. Select the Username / Password Connection (PPTP) radio button and then click on the Next button. Address Mode: PPTP can be used with a dynamic or static IP address. If you select the Dynamic IP radio button, then the IIP address in the next field is not required.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Wireless Click on the Wireless link on the navigation drop-down menu. You will then see four options: basic settings, advanced settings security and site survey. Each option is described below.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Basic Settings (Infrastructure, Adhoc) Click on the Basic Settings link under the Wireless menu. Using this option you may configure the 802.11b/g settings as well as the frequency, channel, and SSID. Band: Depending on the type of wireless clients that are connected to the network, you may select B, G, or B+G.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Advanced Settings Click on the Advanced Settings link under the Wireless menu. On this page you can configure the advanced settings to tweak the performance of your wireless network. Options available are: fragmentation threshold, RTS threshold, beacon interval, output power, preamble type, and 802.11g protection. Authentication Type: select an authentication method. Options available are Open System, Shared Key or Auto.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 RTS Threshold: Packets over the specified size will use the RTS/CTS mechanism to maintain performance in noisy networks and preventing hidden nodes from degrading the performance. Beacon Interval: Beacons will be sent out to devices at the specified intervals. This value is measured in milliseconds (ms). ACK Timeout: You may specify a value for the acknowledge timeout.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Encryption Disabled Encryption: Select None from the drop-down list if your wireless network does not use any type of encryption. Click on the Apply Changes button to confirm the changes. This device will automatically restart once these changes have been applied.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 WEP 64-bit / 128-bit Encryption: Select WEP from the drop-down list if your wireless network uses WEP encryption. WEP is an acronym for Wired Equivalent Privacy, and is a security protocol that provides the same level of security for wireless networks as for a wired network. Set WEP Key: Click on this button to configure the WEP Key.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Key Length: Select a 64-bit or 128-bit from the drop-down list. Key Format: Select a key format from the drop-down list. 64bit-hex keys require 10 characters, where as 128-bit keys require 26 characters. A hex key is defined as a number between 0 through 9 and letter between A through F. Default Tx Key: You may use up to four different keys for four different networks. Select the current key that will be used.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 WPA Authentication Mode: Select the Personal (Pre-Shared Key) radio button. WPA/WPA2: Select TKIP or AES as the cipher suite. Pre-Shared Key Format: Select Passphrase from the drop-down list. Pre-Shared Key: Enter the pass phrase here; this should be between 8 and 63 characters. Click on the Apply Changes button to confirm the changes. This device will automatically restart once these changes have been applied.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Enable WDS - choose to enable/disable Adding WDS AP: Enter MAC address. Set Security – WEP/WPA/WPA2-mixed Show Statistics – shows details of WDS AP Apply settings – click to save settings. Version 1.1 Firewall The device provides a tight firewall by virtue of the way NAT works.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 The Access Control section allows you to control access in and out of devices on your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications such as peer-to-peer utilities or games. When Access Control is disabled, every device on the LAN has unrestricted access to the Internet.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 MAC Address Filter This feature is used to restrict certain MAC address from accessing the Internet. These filters can be used for securing and restricting your network. Configure MAC Filtering: Select one of the options from the drop-down list. o Turn MAC Filtering OFF: When "OFF" is selected, MAC addresses are not used to control network access.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Enable: Place a check in this box to enable the port forwarding rule. Name: Assign a meaningful name to the virtual server, for example Web Server. Several well-known types of virtual server are available from the Application Name drop-down list. Selecting one of these entries fills some of the remaining parameters with standard values for that type of server. IP Address: Specify the IP address for the virtual server entry.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 DMZ Place check in this box to enable DMZ host. DMZ host is a demilitarized zone used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as web, FTP, email and DNS servers. DMZ IP Address: Specify the IP address of the DMZ host. Click on the Apply changes button to store the changes.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 4 Client Bridge/Router Mode – Config Logging In To configure the Access Point through the web-browser, enter the IP address of the Bridge (default: 192.168.1.1) into the address bar of the web-browser and press Enter. Make sure that the Access Point and your computers are on the same subnet. Refer to Chapter 2 in order to configure the IP address of your computer.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 o System o Uptime: Duration of time since the device was last reset. o Firmware version: Version of the firmware that is currently loaded on the device. Wireless Configuration: o Mode: Wireless configuration mode such as client bridge, AP, or WDS. o Band: Frequency and IEEE 802.11 operation mode (b-only, g-only, or b+g). o SSID: The name used to identify the wireless network.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Operation Mode Click on the Operation Mode link under the Management menu. The Operation Mode allows you to switch from Access Point to Client Bridge mode. Select the AP, Bridge or Bridge Router and then click on the Apply Change button. Wait for about a minute until you see the Pop-Up message. Click on the OK button and then enter the specified IP address into the web-browser.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Refer to Chapter 4 to learn how to configure this device in Bridge/Bridge Router mode. Status Click on the Status link under the Management menu. The Status page is the first page that is displayed once you have logged in. This includes details about the system, wireless, and TCP/IP configuration. System o Uptime: Duration of time since the device was last reset.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Statistics Click on the Statistics link under the Management menu. This page displays the number of sent and received packets on the Ethernet and Wireless interface. Since the packet counter is not dynamic, you must click on the Refresh button for the most recent statistics. Log Click on the Log link under the Management menu. The Log page displays a list of events that are triggered on the Ethernet and Wireless interface.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Since the log is not dynamic, you must click on the Refresh button for the most recent events, or click on the Clear button to clear the log. Upgrade Firmware Click on the Upgrade Firmware link under the Management menu. This page is used to upgrade the firmware on the device. Make sure that downloaded the appropriate firmware from your vendor.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Click on the Save button to save the current settings to a file on the local disk. Click on the Browse button to select the settings file and then click on the Upload button to load the previously saved settings. Click on the Reset button to reset the device to its factory default settings. Click Restart to reboot the device. Password Click on the Password link under the Management menu.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Enter a user name into the first field. Enter a password into the New Password field and then re-type the password into the Confirmed Password field. Then click on the Apply Changes button. By clicking on the Reset button, the user name and password fields will become blank indicating that the username and password has been disabled. TCP/IP Settings Click on the TCP/IP Settings link on the navigation drop-down menu.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Static IP Address IP Address: Enter the IP address. Subnet Mask: Enter the subnet mask for the IP address. Default Gateway: Enter the IP address for the default gateway. DHCP: Since a static IP address is used, this option must be set to Disabled. If this device is a DHCP client and will receive its IP settings from a DHCP server, then select Enabled from the drop-down list.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 DHCP: If this device is a DHCP client and will receive its IP settings from a DHCP server, then select Client from the drop-down list. Enabling the DHCP client will disable the IP address, subnet mask, and default gateway fields. If the DHCP option is disabled, then the IP address, subnet mask, and default gateway fields must be filled in. Click on the Apply Changes button to confirm the changes.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 IP Address: Enter the IP address. Subnet Mask: Enter the subnet mask for the IP address. Default Gateway: Enter the IP address for the default gateway. DHCP: Select Server from the drop-down list since this device is the DHCP server. This device will distribute the IP addresses to the clients associated. DHCP Client Range: Enter the first and last IP address of the range.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Client Bridge Router WLAN Interface DHCP Connection (Dynamic IP address) – Choose this connection type if your ISP provides you the IP address. Most cable modems use this type of connection. PPPoE (Point-to-Point Protocol over Ethernet) – Choose this option if your internet connection requires a user name and password. Most DSL modems use this type of connection.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Static IP Static IP is a fixed IP configuration where all parameters including DNS if any should explicitly configured. VPN pass through is configured here by defining exclusivity. PPPoE This type of connection is usually used for a DSL service and requires a username and password to connect.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Username / Password & Connection type (PPPoE) should be input then click on the Connect button. Address Mode: PPPoE can be used with a dynamic or static IP address. If you select the Dynamic IP radio button, then the IIP address in the next field is not required. However, if you select the Static IP radio button, then the IP address in the next field is required. User Name: Specify the user name which is provided by your ISP.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Wireless Click on the Wireless link on the navigation drop-down menu. You will then see five options: basic settings, advanced settings security, access control and WDS. Each option is described below. Basic Settings Click on the Basic Settings link under the Wireless menu. Using this option you may configure the 802.11b/g settings as well as the frequency, channel, and SSID.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Band: Select the IEEE 802.11 mode from the drop-down list. Options available are 2.4GHz (B), 2.4GHz (G), or 2.4GHz (B+G). Select the appropriate mode based on the type of wireless network. For example, if you are sure that the wireless network will be using only IEEE 802.11g clients, then it is recommended to select 2.4GHz (G) instead of 2.4GHz (B+G) which will reduce the performance of the wireless network.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Authentication Type: select an authentication method. Options available are Open System, Shared Key or Auto. An open system allows any client to authenticate as long as it conforms to any MAC address filter policies that may have been set. All authentication packets are transmitted without encryption. Shared Key sends an unencrypted challenge text string to any device attempting to communicate with the AP.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Data Rate: Select a data rate from the drop-down list. However, it is recommended to select auto for the best performance. Data Rate: If you would like to force a data rate, you may select one from the dropdown list. However, for best performance it is recommended to use the Auto setting. Preamble Type: For best performance, all devices on the wireless network should use the same preamble type.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 WEP 64-bit / 128-bit Encryption: Select WEP from the drop-down list if your wireless network uses WEP encryption. WEP is an acronym for Wired Equivalent Privacy, and is a security protocol that provides the same level of security for wireless networks as for a wired network. Set WEP Key: Click on this button to configure the WEP Key. Key Length: Select a 64-bit or 128-bit from the drop-down list.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Click on the Apply Changes button to confirm the changes and then click on the Close button to return to the pervious window. WPA / WPA2 / WPA2 Mixed Passphrase Encryption: Select WPA, WPA2 or WPA2_Mixed from the drop-down list if your wireless network uses this encryption. WPA (Wi-Fi Protected Access) was designed to improve upon the security features of WEP (Wired Equivalent Privacy).
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Wireless Site Survey Click Refresh to see the WLAN AP’s that was detected with modest details of each of them listed.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Appendix A – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ECB-1220R 11b/g Wireless Client Bridge/AP/Router/Repeater Version 1.1 Appendix B – IC Statement IC statement Operation is subject to the following two conditions: This device may not cause interference and This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 9 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
