Business Solutions User Manual ENH500 version 2.
CONVENTIONS Conventions The following conventions are used to give the user additional information about specific procedures or content. It is important to pay attention to these conventions as they provide information to prevent damage to equipment or personal injury. Example: Indicates information used to demonstrate or explain an associated concept. N/A: General Conventions Indicates that a component or a procedure is not applicable to this model.
CONVENTIONS Typographical Conventions The following typographical conventions are used in this document: Italics Indicates book titles, directory names, file names, path names, and program/process names. Constant width Indicates computer output shown on a computer screen, including menus, prompts, responses to input, and error messages. Constant width bold Indicates commands lines as entered on the computer. Variables contained within user input are shown in angle brackets (< >).
TABLE OF CONTENTS TABLE OF CONTENTS Convent ions Copyright 0- i 0- ix Product Overview Package Cont ent s 1- 1 Product Overview 1- 2 Key Feat ures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 2 Benefit s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 3 Technical Specificat ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS I nst alling t he Device 2- 2 Pre- I nst allat ion Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 2 I nst alling t he Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 2 Wall Mount ing t he Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 3 Pole Mount ing t he Device . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Viewing WDS Link List 4- 8 Syst em Set up 4- 9 Configuring Operat ion Mode 4- 9 Configuring I P Set t ings 4- 10 Configuring Spanning Tree Set t ings 4- 11 Rout er Set up 4- 12 Configuring WAN Set t ings 4- 12 St at ic I P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 12 Dynam ic I P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Client Rout er Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 27 Configuring Wireless Securit y 4- 28 Wired Equivalent Privacy ( WEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 28 Wi- Fi Prot ect ed Access Pre- Shared Key ( WPA- PSK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 29 Wi- Fi Prot ect ed Access 2 Pre- Shared Key ( WPA2- PSK) . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Configuring Syst em Tim e 4- 45 Configuring Wi- Fi Schedule 4- 46 Add a Schedule Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- 46 Schedule Services Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS Appendix A Federal Com m unicat ion Com m ission I nt erference St at em ent A- 1 Appendix B I ndust ry Canada St at em ent B- 1 VIII
COPYRIGHT Copyright This user guide and its content is copyright of © EnGenius Networks, 2014. All rights reserved. Any redistribution or reproduction in part or in whole in any form is prohibited. Do not distribute, transmit, store in any form of electronic retrieval system or commercially exploit the content without the expressed written permission of EnGenius Networks.
Product Overview Cha p te r 1
PACKAGE CONTENTS 1.
PRODUCT OVERVIEW 1.2 Product Overview Thank you for choosing ENH500. The ENH500 is a long range, high performance IEEE 802.11a/n network solution that provides Access Point, Client Bridge, WDS, and Client Router functions in a single device. In addition to providing the latest wireless technology, the ENH500 supports Power over Ethernet and Power by Adapter capabilities, which allow the device to be installed easily in nearly any location.
BENEFITS Benefits Wireless extensions to Ethernet networks WLANs enable network managers in dynamic environments to minimize overhead caused by moves, extensions to networks, and other changes. The ENH500 is the ideal product around which you can build your WLAN.
TECHNICAL SPECIFICATION Technical Specification Wireless Specification IEEE802.
PRODUCT OVERVIEW PRODUCT LAYOUT 1.3 Product Layout BACK PANEL VIEW A B C D Figure 1-1: Back Panel View 1-5 Power LED DESCRIPTION OFF = ENH500 is not receiving power ON = ENH500 is receiving power LAN (2) LEDs OFF = ENH500 is not connected to the network.
PRODUCT OVERVIEW PRODUCT LAYOUT A BOTTOM VIEW A LAN Connector B PoE LAN Connector C Reset Button B C DESCRIPTION To configure the ENH500, connect to an Ethernet adapter in a computer. For more information The PoE interface allows the ENH500 to be powered using the supplied PoE injector To reset to factory settings, press button for > 10 seconds.
Installation Cha p te r 2
SYSTEM REQUIREMENTS 2.1 System Requirements To install the ENH500, you need the following: Computer (Windows, Linux, Mac OS X Operating System) Web Browser (Internet Explorer, FireFox, Chrome, Safari) Network Interface equipped: (one of the following) Wired connectivity: Network Interface with an open RJ-45 Ethernet Port Wireless Connectivity: Embedded 802.11n Wi-Fi wireless networking, IEEE 802.11a/n compatible Wi-Fi Card, USB Wi-Fi Dongle (802.
INSTALLING THE DEVICE 2.2 Installing the Device Installing the ENH500 on a pole or wall optimizes the wireless access range. Installing the Device To install the ENH500, use the following procedure to mount the device on a pole and refer to the figure below. Note: Only experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities should install the ENH500. 1.
INSTALLATION INSTALLING THE DEVICE Mounting the ENH500 5. Plug the other end of the Ethernet cable into the PoE port of the PoE injector. To install the ENH500, use the following procedure to mount the device on a wall and refer to the figure below Figure 2-1: Installing the ENH500 Anchor: 8mm (D) x 25mm (L); Screw: 5.5mm (D) x 18mm (L) Figure 2-2: Wall Mouting the ENH500 6. Turn over the ENH500. Then insert the pole mounting strap through the middle hole of the ENH500.
Web Configuration Cha p te r 3
LOGGING IN 3.1 Logging In The ENH500 has a built-in Web Configurator that lets you manage the unit from any location using a Web browser that supports HTTP and has Javascript installed. 3. When the login screen appears, enter admin for the username in the top field and admin for the password in the bottom field. After configuring the computer for TCP/IP using the procedure appropriate for your operating system, use that computer’s Web browser to log in to the ENH500 Web Configurator. 1.
BEST PRACTICES Best Practices Perform the following procedures regularly to make the ENH500 more secure and manage the ENH500 more effectively. Change the default password Use a password that is not easy to guess and that contains different characters, such as numbers and letters. The ENH500 username cannot be changed. For more information, see Configuring Administrator Account. Back up the configuration and be sure you know how to restore it.
Basic Network Settings Cha p te r 4
SYSTEM STATUS 4.1 System Status View the summary of the current system status including system (hardware/software version, date/time), wired network (LAN) and wireless network (WLAN) information. 4.1.1 Using Save/Reload Save and apply the settings shown in the Unsaved changes list, or cancel the unsaved changes and revert to the previous settings that were in effect.
VIEWING SYSTEM INFORMATION 4.1.2 Viewing System Information Displays status information about the current operating mode. System Information shows the general system information such as operating mode, system up time, firmware version, serial number, kernel version, and application version. LAN Settings shows Local Area Network settings such as the LAN IP address, subnet mask, and MAC address.
VIEWING SYSTEM INFORMATION WAN Settings shows Wide Area Network settings such as the MAC address, connection type, connection status, LAN IP address, subnet mask, primary and secondary DNS. Current Wireless Settings shows wireless information such as frequency and channel. Since the ENH500 supports multipleSSIDs, information about each SSID, such as its ESSID and security settings, are displayed.
VIEWING WIRELESS CLIENT LIST 4.1.3 Viewing Wireless Client List Displays a list of clients associated to the ENH500, along with the MAC addresses and signal strength for each client. To remove an SSID client from the list, click the button that appears in the Kick and Ban column. Click the Refresh button to update the client list.
VIEWING SYSTEM LOG 4.1.4 Viewing System Log The ENH500 automatically logs events to internal memory. Note: The oldest events are deleted from the log when memory is full. Click the Refresh button to update the client list or the Clear button to remove all events.
VIEWING CONNECTION STATUS 4.1.5 Viewing Connection Status Displays the current status of the network. The WLAN information shown includes network type, SSID, BSSID, connection status, wireless mode, current channel, security, data rate, noise level, and signal strength. The WAN information shown includes the MAC address, connection type, connection status, IP address, IP subnet mask, primary DNS and secondary DNS.
VIEWING DHCP CLIENT TABLE 4.1.6 Viewing DHCP Client Table Displays the clients that are associated to the ENH500 through DHCP. The MAC addresses and signal strength for each client are also shown. Click the Refresh button to update the client list.
VIEWING WDS LINK LIST 4.1.7 Viewing WDS Link List Displays the clients that are associated to the ENH500 through WDS. The MAC addresses, link status and signal strength for each client are also shown. Click the Refresh button to update the client list.
SYSTEM SETUP 4.2 System Setup The following sections explain the features and functionality of the ENH500 in access point mode, client bridge mode, WDS access point mode, WDS bridge mode, WDS station mode and client router mode. 4.2.1 Configuring Operation Mode Set the primary function of the device. The function that is selected affects which items are available in the main menu. Device Name Enter a name for the device. The name you type appears in SNMP management.
CONFIGURING IP SETTINGS 4.2.2 Configuring IP Settings Configure the ENH500 LAN settings for the ENH500 using a static or dynamic IP address. IP Network Setting Configure the network connection type using either a static IP or dynamic IP. IP Address Enter the LAN IP address of the ENH500. Subnet Mask Enter the subnet mask of the ENH500. Default Gateway Enter the default gateway of the ENH500. Primary DNS Enter the primary DNS address of the ENH500.
CONFIGURING SPANNING TREE SETTINGS 4.2.3 Configuring Spanning Tree Settings Spanning Tree Status Enable or disable the ENH500 Spanning Tree function. Bridge Hello Time Specify Bridge Hello Time, in seconds. This value determines how often the ENH500 sends hello packets to communicate information about the topology throughout the entire Bridged Local Area Network Bridge Max Age Specify Bridge Max Age, in seconds.
ROUTER SETUP 4.3 Router Setup 4.3.1 Configuring WAN Settings Configure the WAN settings for the ENH500 using a static or dynamic IP address, PPPoE or PPTP. Static IP Setting a static IP address allows an administrator to set a specific IP address for the router and guarantees that it can not be assigned a different address. Account Name Enter the account name provided by your ISP. Domain Name Enter the domain name provided by your ISP.
DYNAMIC IP Secondary DNS Enter the secondary DNS server address. Discard Ping on WAN Check to Enable to recognize pings on the ENH500 WAN interface or Disable to block pings on the ENH500 WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings provides some extra security from hackers. Click Accept to save the settings or Cancel to discard changes.
POINT-TO-POINT PROTOCOL OVER ETHERNET (PPPOE) Point-to-Point Protocol over Ethernet (PPPoE) Point-to-Point Protocol over Ethernet (PPPoE) is used mainly by ISPs that provide DSL modems to connect to the Internet. MTU Enter the maximum transmission unit (MTU). The MTU specifies the largest packet size permitted for an internet transmission (PPPoE default: 1492). The MTU size can be set between 576 and 1492. Login Enter the username assigned by an ISP. Password Enter the password assigned by an ISP.
POINT-TO-POINT TUNNELLING PROTOCOL (PPTP) Point-to-Point Tunnelling Protocol (PPTP) The point-to-point tunnelling protocol (PPTP) is used in association with virtual private networks (VPNs). There a two parts to a PPTP connection: the WAN interface settings and the PPTP settings. MTU Enter the maximum transmission unit (MTU). The MTU specifies the largest packet size permitted for an internet transmission (PPPoE default: 1400). The MTU size can be set between 1200 and 1400.
POINT-TO-POINT TUNNELLING PROTOCOL (PPTP) Use These DNS Servers Click the radio button to set up the Primary DNS and Secondary DNS servers manually. Discard Ping on WAN Check to Enable to recognize pings on the ENH500 WAN interface or Disable to block pings on the ENH500 WAN interface. Note: Pinging IP addresses is a common method used by hackers to test whether the IP address is valid. Blocking pings provides some extra security from hackers. Click Accept to save the settings or Cancel to discard changes.
CONFIGURING LAN SETTINGS 4.3.2 Configuring LAN Settings IP Address Enter the LAN port IP address. IP Subnet Mask Enter the LAN IP subnet mask. WINS Server IP Enter the WINS Server IP. Use Router As DHCP Server Check this option to enable the ENH500 internal DHCP server. Starting IP Address Specify the starting IP address range for the pool of allocated for private IP addresses.
CONFIGURING VPN PASS-THROUGH 4.3.3 Configuring VPN Pass-Through VPN Pass-through allows a secure virtual private network (VPN) connection between two computers. Enabling the options on this page opens a VPN port and enables connections to pass through the ENH500 without interruption. PPTP Pass-through Check this option to enable PPTP pass-through mode. L2TP Pass-through Check this option to enable L2TP pass-through mode. IPSec Pass-through Check this option to enable IPSec pass-through mode.
CONFIGURING PORT FORWARDING 4.3.4 Configuring Port Forwarding Port forwarding enables multiple server applications on a LAN to serve clients on a WAN over a single WAN IP address. The router accepts incoming client packets, filters them based on the destination WAN, or public, port and protocol and forwards the packets to the appropriate LAN, or local, port. Unlike the DMZ feature, port forwarding protects LAN devices behind the firewall. NO. Displays the sequence number of the forwarded port.
CONFIGURING PORT FORWARDING Service Name Enter a name for the port forwarding rule. Protocol Select a protocol for the application: Choices are Both, TCP, and UDP. Starting Port Enter a starting port number. Ending Port Enter an ending port number. All ports numbers between the starting and ending ports will forward users to the IP address specified in the IP Address field. IP Address Enter the IP address of the server computer on the LAN network where users will be redirected.
CONFIGURING DEMILITARIZED ZONE 4.3.5 Configuring Demilitarized Zone Configuring a device on the LAN as a demilitarized zone (DMZ) host allows unrestricted two-way Internet access for Internet applications, such as online video games, to run from behind the NAT firewall. The DMZ function allows the router to redirect all packets going to the WAN port IP address to a particular IP address on the LAN.
CONFIGURING WIRELESS LAN 4.4 Configuring Wireless LAN 4.4.1 Configuring Wireless Settings Instructions on how to configure the wireless and security settings for each of the possible operating modes. ! WARNING! Incorrectly changing these settings may cause the device to stop functioning. Do not modify the settings in this section without a thorough understanding of the parameters. Access Point Mode The ENH500 supports Access Point Mode.
ACCESS POINT MODE Current Profile Configure up to four different SSIDs. If many client devices will be accessing the network, you can arrange the devices into SSID groups. Click Edit to configure the profile and check whether you want to enable extra SSIDs. Click Accept to confirm the changes or Cancel to cancel and return previous settings. SSID Specify the SSID for the current profile. VLAN ID Specify the VLAN tag for the current profile. Suppressed SSID Check this option to hide the SSID from clients.
CLIENT BRIDGE MODE Client Bridge Mode Client Bridge Mode lets you connect two LAN segments via a wireless link as though they are on the same physical network. Since the computers are on the same subnet, broadcasts reach all machines. As a result, DHCP information generated by the server reach all client computers as though the clients residing on one physical network. Wireless Mode Wireless mode supports 802.11a/n mixed modes. SSID Specify the SSID if known.
WDS BRIDGE MODE WDS Bridge Mode Unlike traditional bridging. WDS Bridge Mode allows you to create large wireless networks by linking several wireless access points with WDS links. WDS is normally used in large, open areas, where pulling wires is cost prohibitive, restricted or physically impossible. Wireless Mode Wireless mode supports 802.11a/n mixed modes. Channel HT Mode The default channel bandwidth is 40 MHz. The larger the channel, the better the transmission quality and speed.
WDS BRIDGE MODE Security Select the type of WDS security: None, WEP, or AES. WEP Key Enter the WEP key. AES Pass phrase Enter the AES pass phrase. MAC Address Enter the MAC address of the Access Point to which you want to extend wireless connectivity. Mode Select Disable or Enable to disable or enable WDS. Click Accept to confirm the changes or Cancel to cancel and return previous settings.
CLIENT ROUTER MODE Client Router Mode In Client Router Mode, you can access the Internet wirelessly with the support of a WISP. In AP Router Mode, the ENH500 can access the Internet via a cable or DSL modem. In this mode, the ENH500 can be configured to turn off the wireless network name (SSID) broadcast, so that only stations that have the SSID can be connected.
CONFIGURING WIRELESS SECURITY 4.4.2 Configuring Wireless Security The Wireless Security Settings section lets you configure the ENH500’s security modes: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. We strongly recommend you use WPA2-PSK. Wired Equivalent Privacy (WEP) Security Mode Select WEP from the drop-down list to begin the configuration. Auth Type Select Open System or Shared. Input Type Select an input type of Hex or ASCII.
WI-FI PROTECTED ACCESS PRE-SHARED KEY (WPA-PSK) Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Security Mode Select WPA-PSK from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Passphrase Specify the security password. For security, each typed character is masked by a dot.
WI-FI PROTECTED ACCESS 2 PRE-SHARED KEY (WPA2-PSK) Wi-Fi Protected Access 2 Pre-Shared Key (WPA2-PSK) Security Mode Select WPA2-PSK from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Passphrase Specify the security password. For security, each typed character is masked by a dot.
WI-FI PROTECTED ACCESS PRE-SHARED KEY (WPA-PSK) MIXED Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) Mixed Security Mode Select WPA2-PSK Mixed from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Passphrase Specify the security password.
WI-FI PROTECTED ACCESS (WPA) Wi-Fi Protected Access (WPA) Security Mode Select WPA from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Radius Server Specify the IP address of the RADIUS server. Radius Port Specify the port number that your RADIUS server uses for authentication.
WI-FI PROTECTED ACCESS 2 (WPA2) Wi-Fi Protected Access 2 (WPA2) Security Mode Select WPA2 from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Radius Server Specify the IP address of the RADIUS server. Radius Port Specify the port number that your RADIUS server uses for authentication.
WI-FI PROTECTED ACCESS (WPA) MIXED Wi-Fi Protected Access (WPA) Mixed Security Mode Select WPA Mixed from the drop-down list to begin the configuration. Encryption Select Both, TKIP, or AES as the encryption type. Both = uses TKIP and AES. TKIP = automatic encryption with WPA-PSK; requires passphrase. AES = automatic encryption with WPA2-PSK; requires passphrase. Radius Server Specify the IP address of the RADIUS server.
CONFIGURING WIRELESS MAC FILTER 4.4.3 Configuring Wireless MAC Filter Note: This section applies to Access Point and WDS Access point mode. Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC addresses. You can manually add a MAC address to restrict the permission to access ENH500. The default setting is Disable Wireless MAC Filters.
CONFIGURING WDS LINK SETTINGS 4.4.4 Configuring WDS Link Settings Using WDS Link Settings, you can create a wireless backbone link between multiple access points that are part of the same wireless network. This allows a wireless network to be expanded using multiple Access Points without the need for a wired backbone to link them, as is traditionally required. Security Select the type of WDS security: None, WEP, or AES. WEP Key Enter the WEP key. AES Passphrase Enter the AES passphrase.
CONFIGURING ADVANCED NETWORK SETTINGS 4.4.5 Configuring Advanced Network Settings Configure the advanced wireless settings for your access point using the screens in this section. Leave these settings to their default values if you are not sure what values to enter. Data Rate Select a data rate from the drop-down list. The data rate affects throughput. If you select a low data rate value, for example, the throughput is reduced but the transmission distance increases.
MANAGEMENT SETUP 4.5 Management Setup The Management section lets you configure administration, management VLAN, SNMP settings, backup/restore settings, firmware upgrade, time settings, and log settings. This chapter describes these settings. 4.5.1 Configuring Administrator Account Click the Administration link under the Management menu to change the user name and password used to log on to the ENH500 Web Configurator. The default user name is admin and the default password is admin.
CONFIGURING MANAGEMENT VLAN 4.5.2 Configuring Management VLAN Click the Management VLAN link under the Management menu to assign a VLAN tag to the packets. A VLAN is a group of computers on a network whose software has been configured so that they behave as if they were on a separate Local Area Network (LAN).
CONFIGURING SNMP 4.5.3 Configuring SNMP SNMP is used in network management systems to monitor network-attached devices for conditions that warrant administrative attention. SNMP Enable or disable the ENH500 SNMP function. Contact Enter the contact details of the device. Location Enter the location of the device. Community Name (Read Only) Enter the password for accessing the SNMP community for read-only access.
CONFIGURING SNMP Engine ID Specify the engine ID for SNMPv3. Click Save/Apply to apply the changes or Cancel to return previous settings.
CONFIGURING BACKUP/RESTORE SETTINGS 4.5.4 Configuring Backup/Restore Settings Click the Backup/Restore Setting link under the Management menu to save the ENH500’s current settings in a file on your local disk or load settings onto the device from a local disk. This feature is particularly convenient administrators who have several ENH500 devices that need to be configured with the same settings. This page also lets you return the ENH500 to its factory default settings.
CONFIGURING AUTO REBOOT SETTINGS 4.5.5 Configuring Auto Reboot Settings Click the Auto Reboot Settings link under the Management menu to enable or disable the Auto Reboot function. This feature is particularly convenient to administrators for the scheduling of auto rebooting on the device. This page also allows you to set the frequency of this function. Auto Reboot Setting Select Enable from the drop-down menu to setup this function.
CONFIGURING FIRMWARE UPGRADE 4.5.6 Configuring Firmware Upgrade Firmware is system software that operates and allows the administrator to interact with the router. ! WARNING! Upgrading firmware through a wireless connection is not recommended. Firmware upgrading must be performed while connected to an Ethernet (LAN port) with all other clients disconnected. The firmware upgrade procedure can take several minutes.
CONFIGURING SYSTEM TIME 4.5.7 Configuring System Time Change the system time of the ENH500 by manually entering the information, synchronizing the device with a PC, or setup automatic updates through a network time (NTP) protocol server. Manually Set Date and Time Enter the date and time values in the date and time fields or click the Synchronize with PC button to get the date and time values from the administrator’s PC.
CONFIGURING WI-FI SCHEDULE 4.5.8 Configuring Wi-Fi Schedule Use the Wi-Fi schedule function to control the wireless power ON/OFF service that operates on a routine basis. Add a Schedule Service Create a schedule service type and date/time parameters for a specific service. Schedule Name Enter the description of the schedule service. Service Select the type of schedule service, either Wireless Power ON or Wireless Power OFF. Day Select the days of the week to enable the schedule service.
SCHEDULE SERVICES TABLE Schedule Services Table The Schedule function relies on the GMT time setting acquired from a network time protocol (NTP) server. For details on how to connect the ENH500 to an NTP server, see Configuring System Time. Schedule Table Displays a list of scheduled services for the ENH500. The properties of each service displayed are: # Displays the ID number of the service in the table. Name Displays the description of the service.
CONFIGURING COMMAND LINE INTERFACE 4.5.9 Configuring Command Line Interface Most users will configure the ENH500 through the graphical user interface (GUI). However, for those who prefer an alternative method there is the command line interface (CLI). The CLI can be access through a command console, modem or Telnet connection. CLI Select to enable or disable the ability to modify the ENH500 via a command line interface (CLI). Click Save/Apply to apply the changes or Cancel to return previous settings.
CONFIGURING LOGGING 4.5.10 Configuring Logging Display a list of events that are triggered on the ENH500 Ethernet and wireless interfaces. You can consult this log if an unknown error occurs on the system or when a report needs to be sent to the technical support department for debugging purposes. Syslog Enable or disable the ENH500 syslog function. Log Server IP Address Enter the IP address of the log server. Local Log Enable or disable the local log service.
CONFIGURING DIAGNOSTICS 4.5.11 Configuring Diagnostics The diagnosis feature allow the administrator to verify that another device is available on the network and is accepting request packets. If the ping result returns alive, it means a device is on line. This feature does not work if the target device is behind a firewall or has security software installed. Target IP / Domain Name Enter the IP address you would like to search. Ping Packet Size Enter the packet size of each ping.
VIEWING DEVICE DISCOVERY 4.5.12 Viewing Device Discovery Device Name Displays the name of the devices connected to the network. Operation Mode Displays the operation mode of the devices connected to the network. IP Address Displays the IP address of the devices connected to the network. System MAC Address Displays the system MAC address of the devices connected to the network. Firmware Version Displays the firmware version of the devices connected to the network.
CONFIGURE DENIAL OF SERVICE PROTECTION 4.5.13 Configure Denial of Service Protection Use TCP SYN Cookies Protection Click to enable TCP SYN cookies protection. SYN Flood Attack Protection Click to enable or disable SYN Flood Attack Protection. Match Interval Per Second Enter the allowed number of packets per second. Limit Packets Enter the maximum number of packets allowed per request. UDP Flood Attack Protection Click to enable or disable UDP Flood Attack Protection.
LOGGING OUT 4.5.14 Logging Out Click Logout to logout from the EENH500.
Appendix
Appendix A Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix B - CE Interference Statement Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
This device is a 5GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
Français [French] Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
APPENDIX C INDUSTRY CANADA STATEMENT Appendix C Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
