Dual Band Wireless-N 300Mbps Media USB Adapter EUB600 User’s Manual Version v1.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Table of Contents 1 2 3 4 5 INTRODUCTION .................................................................................................................................... 3 FEATURES & BENEFITS ..................................................................................................................................... 3 PACKAGE CONTENTS .....................................................................................................
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 1 Introduction The high-speed wireless USB 2.0 client adapter is the most convenient way to let you put a desktop/notebook computer almost anywhere without the hassle of running network cables. Now you don’t need to suffer from drilling holes and exposed cables. Once you are connected, you can do anything, just like the wired network. This USB client adapter operates seamlessly in 2.4GHz & 5Ghz frequency spectrum supporting the 802.11a, 802.11b, 802.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Support 2Tx * 2Rx Radio With Intelligent Antenna enables WMM (IEEE 802.11e) standard support Wireless Multimedia Enhancements Quality of Service support (QoS) / enhanced power saving for Dynamic Networking USB 2.0/1.1 USB 2.0 interface and compatible with USB 1.1 Package Contents Open the package carefully, and make sure that none of the items listed below are missing.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Applications The wireless LAN products are easy to install and highly efficient. The following list describes some of the many applications made possible through the power and flexibility of wireless LANs: a) Difficult-to-wire environments There are many situations where wires cannot be laid easily. Historic buildings, older buildings, open areas and across busy streets make the installation of LANs either impossible or very expensive.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter This is the easiest and least expensive way for the SOHO to set up a wireless network. The image below depicts a network in ad-hoc mode. b) Infrastructure Mode The infrastructure mode requires the use of an Access Point (AP). In this mode, all wireless communication between two computers has to be via the AP. It doesn’t matter if the AP is stand-alone or wired to an Ethernet network.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 2 USB Adapter for Windows (XP, Vista and Win7) Before You Begin WiFi Alliance certification recommends WPA2 AES to be the security mechanism under 11N mode. System driver will automatically bring down wireless data rate to 54Mbps if other security method such as WEP or WPA is used under 11n mode.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Installing the windows Drivers Follow the steps below in order to install the USB adapter drivers: 1. Insert the CD-ROM that was provided to you in this package. The setup should run automatically. If the setup does not run automatically, then must manually select the Autorun.exe file from the CD-ROM drive. 2. Click on Driver / Utility to go to the Driver page. 3. Click For Windows XP or above version to start the install process.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 4. Once the setup begins you will see the InstallShield Wizard. Select Install driver and EnGenius WLAN Utility and then click on the Next> button. 5. Click on the Install button to begin the installation.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 6. Wait for a few seconds until the driver and client utility is installed. 7. The installation is complete. Click on the Finish button.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 8. Carefully insert the USB adapter into the USB port. Windows will then detect and install the new hardware. 9. An EG icon will then appear in the system tray. Right click on the EG icon and then click on Launch Config Utility. Note: Click on Use Zero Configuration as Configuration Utility if you would like to use Windows Zero Configuration (XP only feature).
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Main interface of the utility The function buttons on the top(From L to R )are respectively Site Survey, Link Information, Profile, Advanced, About, and MiniSize the Interface. While the left column displays Turn On/Off RF, Security /No security, and Signal status. Site Survey The “Site Survey” screen displays currently scanned wireless signals and you can click one to connect the signal.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Link Information After successfully connected to one wireless network, you can view its detailed information by clicking the “Link Information” on the main interface. 1. “Link Status” screen displays the detailed information of the connected AP including its SSID,MAC address, authentication type, encryption type, network type and channel. 2.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Profile Except the above common connection type, you can also connect to the wireless network by adding a profile on the “Profile“screen.The Profile screen is used to save the wireless network parameters. When the adapter is successfully connected to a network, the profile name of this network will automatically be added here, which helps the adapter to quickly connect to the wireless network next time.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Export: export the configured profile. Add WPS Profile: WPS setting requires that the connecting wireless device support WPS function. WPS helps you to fulfill wireless encryption fast as well as secure your wireless network. For detailed setting steps, refer to appendix2. There are two network types for your option when clicking the “Add” button to add wireless adapter connection: Infrastructure and Ad-Hoc.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Click the next button to select the authentication type and encryption type such as WPA－PSK and AES, and then input the key and click next. After a profile is successfully added, the profile name can be seen on the profile list,you can edit , import or export the profile,click “Active” to finish the connection,now you can also view the detailed connection status on the “Link Information”screen. Note: Please refer to page.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter NOTE: If the SSID broadcast function of the wireless router or AP you wish to connect is disabled, then the wireless adapter can not scan the SSID, thus you need to connect by creating the corresponding profile. 2.Ad-Hoc Profile management Using the Ad-hoc mode to establish a wireless network requires that each computer should be equipped with a wireless network adapter. By connecting these wireless adapters, computers are able to share the resources.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter c.Select “Internet Protocol(TCP/IP)”and click “Properties”. d. Please enter the IP address and subnet mask, and make sure this IP address is not used by other devices in the network.For example: if your wireless adapter’s IP address is 192.168.0.1， then set other wireless adapters’ IP addresses within the range of 192.168.0.2— 192.168.0.254.Click “Ok” to save the settings.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Click the “Next” button to select the authentication type and encryption type and then input the correct key and click “Next”. After a profile is successfully added,the profile can be seen on the profile list ,select it and click the “Active” icon on the lower right corner. Note: Please refer to page.23 for detail security wireless encryption settings.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter And then search for the wireless network on other clients. Double click the wireless network you have configured and you’ll be prompted for the key .After entering the key, click “Connect”. When the highlighted part shows “Connected“ ,it indicates the connection is successful.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Advanced This section is used to set the channels. About This screen mainly displays the version information of the UI’s different programs as well as EnGenius’s copyright statement.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 3 Authentication and Security WiFi Alliance certification recommends WPA2 AES to be the security mechanism under 11N mode. System driver will automatically bring down wireless data rate to 54Mbps if other security method such as WEP or WPA is used under 11n mode. If your 11N router is using security mechanism other than WPA2 AES, you are recommended to disable security setting or change it to WPA2 AES to fully utilize 11N capability.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Authentication Type: Select Open or Shared from the drop-down list. Encryption: Select WEP from the drop-down list. Default TX Key: Choose the Key 1~Key4 you want to use. WEP Key Format (Hex or ASCII): Type a character string into the field. For 64-bit enter 5 alphanumeric or 10 hexadecimal characters. For 128-bit enter 13 alphanumeric or 26 hexadecimal characters. Click on the right arrow button to save the changes.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Setting Up CCKM, 802.1X, WPA or WPA2 a. In the Profile Settings security screen, select an authentication and encryption method. • To set up WPA or WPA2 authentication, for Authentication select WPA or WPA2, and for Encryption select TKIP or AES. If WPA2 is selected, TKIP and AES are available with the added security of management frame protection (TKIP, AES). Click the right arrow to save your settings.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter b. Select the EAP method (Extensible Authentication Protocol) supported by your network and follow the instructions given. PEAP i. If you select PEAP, for Tunnel Authentication select either EAP-MSCHAP v2, EAPTLS/Smart Card, or Generic Token Card. • If you select EAP-MSCHAP v2, in the Tunnel ID field type the name assigned to the user, and in the Tunnel Password field, type the password associated with the user name.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter • o o o o If you select Generic Token Card, in Tunnel Password/Mode, you can select Static Password or Soft Token and for Vista/Windows 7 users, Windows Logon or Prompt User, depending on the method used to supply user credentials. If you select the Static Password option, then in the Tunnel ID field, type your user name, and in the Tunnel Password field, type the password associated with your user name.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter iv. If you have selected PEAP > EAP-TLS/Smart Card, from the drop-down list, select the client certificate on your computer to be used by this security method, or for Vista and Windows 7 users, select "Use my smart card" to set up smart card-based user authentication. Click the right arrow to save your settings. v. You have completed setup of PEAP authentication. TLS/Smart Card vi.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter vii. From the drop-down list, select the client certificate on your computer to be used by this security method, or for Vista and Windows 7 users, select "Use my smart card" to set up smart card-based user authentication. Click the right arrow to save your settings. viii. Optionally select Use Server Certification, and from the drop-down box, select the certificate authority. Click the right arrow to save your settings. ix.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter TTLS (Windows XP only) x. For Windows XP users only. To apply TTLS, select a Tunnel Authentication method from the drop-down list. Options include CHAP, MS-CHAP, MS-CHAP v2, PAP, and EAP-MD5. For Tunnel ID, select Authentication ID or Machine ID depending on whether user credentials are provided by the user or by the computer from which they are accessing the network. If Authentication ID is selected, in the adjacent field, type your user name.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter xiii. You have completed setup of TTLS authentication. EAP-FAST xiv. If you are applying EAP-FAST authentication using Vista or Windows 7, click the right arrow to finish setting up EAP-FAST. xv. Otherwise, for Windows XP users only, select a Tunnel Authentication method from the drop-down list. Options include EAP-MS-CHAP v2, EAP-TLS/Smart Card, and Generic Token Card.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter • o o If you select Generic Token Card, for 'Tunnel ID', field requirements depend on the tunnel mode and identification method selected. If 'Static Password' is selected for Tunnel Mode, and either Authentication ID or Machine ID are selected, type a password. For Authentication ID a user name is also required in the adjacent field. If 'Soft Token' is selected for Tunnel Mode, no further settings are required.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter xvii. For Windows XP users only, if you selected EAP-TLS/Smart Card as the tunnel authentication method, from the drop-down list select a security certificate on your computer. Click the right arrow to save your settings. xviii. For Windows XP, Vista and Windows 7, the Utility supports automatic login using your EAP-FAST settings on Windows startup. Select 'Use Pre-logon Connection' to enable this function.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter xxi. In the screen that appears select a Key and Key Format setting supported by the wireless router or AP to which you are connecting. • If you select 'Hex(10 or 26 hex digits)', in the WEP Key field type a security key 10 or 26 characters long made up of digits '0'-'9' and letters 'A'-'F'.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter xxiv. For Windows Vista and 7 users, for Tunnel Mode, you can select Static Password, Windows Logon or Prompt User, depending on the method used to supply user credentials. o If you select the Static Password option, then in the Tunnel ID field, type your user name, and in the Tunnel Password field, type the password associated with your user name. o If you select Windows Logon, your user credentials are based on those of your Windows user account.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 35
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 4 Uninstall the Drivers & Client Utility If the USB client adapter installation is unsuccessful for any reason, the best way to solve the problem may be to completely uninstall the USB adapter and its utility and repeat the installation procedure again. Follow the steps below in order to uninstall the client utility: 1. Click on Start > EnGenius Wireless > Uninstall EnGenius Wireless USB Adapter 2. The un-installation process will then begin.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 3. Click on the Yes button to confirm the un-installation process and then click on the Next button. 4. The un-installation process is complete. Select Yes, I want to restart my computer now radio button and then click on the Finish button. Then remove the USB adapter.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 5 USB Adapter for MAC OS X Installing the Drivers Follow the steps below in order to install the USB adapter drivers: 1. Insert the CD-ROM that was provided to you in this package. The setup should run automatically. If the setup does not run automatically, then you must manually select the Autorun.exe file from the CD-ROM drive. 2. Click on Driver / Utility to go to the Driver page. 3. Click For MAC OS X to start the install process. 4.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 5. Select the Macintosh HD and then click on the Continue button.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 6. Click on the Continue button to configure the next step. 7. The installation is complete. Click on the Restart button. 8. Carefully insert the USB adapter into the USB port. MAC OS X will then detect and install the new hardware. 9. The Client Utility is installed in the Applications folder.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Profiles The Profile tab is used to store the settings of multiple Access Points such as home, office, café, etc. When adding a profile you are required to enter a profile name and SSID as well as configure the power-saving mode, network type, RTS/fragmentation threshold and encryption/authentication settings. A profile can be configured as Infrastructure or Ad-hoc mode. The configuration settings for each mode are described below.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Profile: Enter a name for the profile; this does not need to be the same as the SSID. SSID: Enter the SSID of the network or select one from the drop-down list. The SSID is a unique name shared among all points in your wireless network. The SSID must be identical for all points in the network, and is case-sensitive. PSM: Select a power saving mode (PSM) option.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Ad-hoc Mode This is the simplest network configuration with several computers equipped with the PC Cards that form a wireless network whenever they are within range of one another. In ad-hoc mode, each client is peer-to-peer, would only have access to the resources of the other client and does not require an access point. This is the easiest and least expensive way for the SOHO to set up a wireless network.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter fragmented. Click on the OK button to save the changes. Authentication and Security The Security tab allows you to configure the authentication and encryption settings such as: WEP, WPA-PSK, WPA2-PSK and 802.1x. Each security option is described in detail below. WEP Encryption The WEP tab displays the WEP settings. Encryption is designed to make the data transmission more secure.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Show Password check box. If you want to make sure the accuracy of password you type, click the Show Password box to check it. WPA-PSK & WPA2-PSK Authentication & TKIP, AES Encryption WPA – PSK (Pre-shared Key) is used in a Pre Shared Key mode that does not require an authentication server. Access to the Internet and the rest of the wireless network services is allowed only if the pre-shared key of the computer matches that of the Access Point.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Link Status The Link Status tab displays the current status of the wireless radio. The following information is included in this tab, as the image depicts below. Status: This indicates the state of the client. There are three options: o Associated: Indicates that the wireless client is connected to an Access Point (AP). The BSSID is shown in the form of 12 HEX digits, which is the MAC address of the AP.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter GI: Guard Interval MCS: Modulation Coding Scheme dBm Check Box. When you click on the check box as the drawing below. The signal strength and noise level will be shown as the dBm measurements. Site Survey The Site Survey tab displays a list of Access Points and Stations in the area, and allows you to connect to a specific one. The following information is included in this tab, as the image depicts below.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Add Profile: Click on this button to add the SSID and its associated settings into a profile. Click on the OK button if you have made any changes. Statistics The Statistics tab displays transmit and receive packet statistics in real-time. Information included is frames transmitted/received successfully, transmitted successfully without and after retry, received with CRC error, duplicate frames received, etc.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Wireless mode: Select 802.11 2.4GHz, 5GHz and 2.4+5GHz. Tx Rate: The transmit rate should is set to auto by default. Tx BURST: Click the check box will enhance the throughput Click on the Apply button to save the changes. WPS WPS (Wireless Push Button) is used for WiFi Protected Setup.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Rescan: Click on this button to view a list of Access Points in the area.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter About The About tab displays information about the device, such as: the network driver version and date, configuration utility version and date, and the NIC (Network Interface Card) firmware version and date.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Appendix A – Glossary 8 802.11 A A family of specifications for wireless local area networks (WLANs) developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). Access Control List ACL. This is a database of network devices that are allowed to access resources on the network. Access Point ActiveX AP.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter they are claiming to be Automatic Private IP Addressing B APIPA.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter A program or user that requests data from a server Collision Cookie D Data When do two devices on the same Ethernet network try and transmit data at the exact same time.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Direct Sequence Spread Spectrum DMZ DNS DSSS: Modulation technique used by 802.11b wireless devices "Demilitarized Zone". A computer that logically sits in a "no-mans land" between the LAN and the WAN. The DMZ computer trades some of the protection of the router's security mechanisms for the convenience of being directly addressable from the Internet.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Firewall A device that protects resources of the Local Area Network from unauthorized users outside of the local network Firmware Programming that is inserted into a hardware device that tells it how to function Fragmentation FTP Breaking up data into smaller pieces to make it easier to store File Transfer Protocol.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter I A networking device that connects multiple devices together ICMP IEEE IGMP IIS IKE Internet Control Message Protocol Institute of Electrical and Electronics Engineers Internet Group Management Protocol is used to make sure that computers can report their multicast group membership to adjacent routers Internet Information Server is a WEB server and FTP server provided by Microsoft Internet Key Exchange is used to ensure security for VPN connection
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter J Internet Service Provider Java K Kbps Kbyte L L2TP LAN Latency LED Legacy A programming language used to create programs and applets for web pages Kilobits per second Kilobyte Layer 2 Tunneling Protocol Local Area Network The amount of time that it takes a packet to get from the one point to another on a network.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter MPPE MTU Microsoft Point-to-Point Encryption is used to secure data transmissions over PPTP connections Maximum Transmission Unit is the largest packet that can be transmitted on a packet-based network like the Internet Multicast N NAT Sending data from one device to many devices on a network Network Address Translation allows many private IP addresses to connect to the Internet, or another network, through one IP address NetBEUI NetBIOS Exten
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter A sequence of characters that is used to authenticate requests to resources on a network Personal Area Network The interconnection of networking devices within a range of 10 meters Physical layer Ping PoE POP3 Port PPP PPPoE PPTP The first layer of the OSI model. Provides the hardware means of transmitting electrical signals on a data carrier A utility program that verifies that a given Internet address exists and can receive messages.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter RJ-11 RJ-45 Routing Information Protocol is used to synchronize the routing table of all the routers on a network The most commonly used connection method for telephones The most commonly used connection method for Ethernet RS-232C RSA S Server The interface for serial communication between computers and other related devices Algorithm used for encryption and authentication A computer on a network that provides services and resources to other c
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Syslog T TCP Determines what portion of an IP address designates the Network and which part designates the Host System Logger -- a distributed logging interface for collecting in one place the logs from different sources. Originally written for UNIX, it is now available for other operating systems, including Windows. Transmission Control Protocol TCP Raw TCP/IP TFTP A TCP/IP protocol for transmitting streams of printer data.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Virtual Private Network VLAN VPN: A secure tunnel over the Internet to connect remote offices or users to their company's network Virtual LAN Voice over IP VoIP W Sending voice information over the Internet as opposed to the PSTN Voice over IP Wake on LAN WAN WCN WDS Allows you to power up a computer though it's Network Interface Card Wide Area Network Windows Connect Now.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter X xDSL Y Wi-Fi Protected Access. A Wi-Fi security enhancement that provides improved data encryption, relative to WEP. A generic term for the family of digital subscriber line (DSL) technologies, such as ADSL, HDSL, RADSL, and SDSL.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Appendix 2 – How to Set WPS WPS setting supports two modes :PBC and PIN. The detailed setting steps are as follows: 1.Wireless Connection in PBC Mode 1.1 Enable the router’s WPS-PBC feature. If your router provides WPS button, just press and hold it for about 1 second, then the WPS LED will be flashing for about 2 minutes, which indicates the router’s WPS feature has been enabled.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Start PBC: Negotiating process: A profile forms automatically after the connection is successfully established.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 1.3 Using the wireless adapter’s WPS button to perform PBC connection. If your wireless adapter provides a WPS button,you may use the button to perform PBC connection. a).Run the adapter’s UI and switch to STATION mode b).Two minutes after the router’s WPS-PBC is enabled,press the adapter’s WPS button to connect in PBC mode. c).You may view the PBC connection process on the UI’s PBC screen. 2.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter First enter its WPS configuration screen,enable WPS settings and select PIN for WPS mode and then input 90982477 in the PIN code field,and then click the “Save” button. When the WPS indicator of the Router starts flashing,it indicates that WPS feature is enabled. Click the next button on the Profile screen and click “Start PIN” to start the PIN code negotiation. 2.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter On the “Add WPS Profile” screen, select the SSID of the AP that need to negotiate in WPS mode instead of selecting”Auto”.Then select”PIN” as the WPS method and click the next button to display the folowing screen: Select “Registrar” as the config mode and enter the router’s PIN code,such as 03736647 that displays on the router’s WPS screen in section 2.1, in the PIN code field here.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter it,just click the next buton. Then click “Start PIN” on the screen below to perform WPS connection. NOTE: 1.Under the WPS connection mode, when multiple routers simultaneously enable the WPS function, it may cause connection failure. 2.If the router connect to the adapter using the WPS, only one client can be connected at one time, and so if the router need to connect to multiple clients through WPS, you should repeat the WPS operation.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Appendix C – FCC Interference Statement Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Appendix C – EU Declaration of Conformity Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter 0560 Česky [Czech] Dansk [Danish] Deutsch [German] Eesti [Estonian] English [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
EUB600 – Dual Band Wireless-N 300Mbps Media USB Adapter Appendix C – Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
