User's Manual

~
49
~
Programmable PBX Options (Register to PRO base only)
1. When DuraFon PRO base unit installed behind the PBX
system, it is feasible to pre-program some PBX features
along with their feature codes into the system.
2.
Up to 9 most frequently used PBX feature codes
can be pre
-
programmed.
3.
Name an
d enter PBX feature codes:
a.
Press
MENU
(Right) soft key while the handset is
in standby.
b.
Press “5” following by “
9
” to enter “PBX Options”
menu.
c.
Press
ADD
soft key to edit a PBX feature to be
memorized.
d.
Key in the name of the PBX feature
s just like
editing a phonebook entry i.e. PBX Transfer.
Press
SAVE
to confirm your entries.
e.
Key in the feature code of the correspondence
PBX feature i.e. Flash*70. Press SAVE to confirm
your entries.
f.
The first PBX feature and the correspondence
feature code you enter will appear on the LCD
screen.
[note] “F” represents the Flash signal
g.
Press
OPTION
soft key to Erase or Edit the PBX
feature you program into the system.
h.
Repeat the same operation to edit the second and
even the third PBX feature that you will use
frequently.
4.
Using pre
-
programmed PBX feature during the call.
a.
Press
OPTION
soft key while the handset is in
talk mode
.
b.
Press the correspondence number of the function
you want to perform i.e. press 1 to perform “PBX
Transfer” function.
c.
Press when you finish the desired function
and back to standby mode.


1
0
Settings: 
8. Line Select
9. PBX Options


1
0
Empty
ADD


1
0
Feature Name?
Caps = *
SAVE DELETE


1
0
Feature Code?
SAVE DELETE


1
0
PBX Transfer
F*70
ADD OPTION


1
0
00:00:16
Volume:4
OPTION HOLD


11
1. PBX Transfer
0. Mute
~
50
~
Notes:
1. This feature would be useful if the DuraFon PRO base unit is
adjunct to a PBX system.
2. Only “Mute” function will be displayed if you have not
preprogrammed any PBX features into the system.
3. The DuraFon PRO’s Programmable PBX Options may not function
with all PBX / Key systems due to the diversity of various
proprietary systems.
Broadcast through PBX (Register to PRO base only)
1. DuraFon PRO and DuraWalkie both have the broadcast function,
each can broadcast another handset without going through the
base station, as long as the handsets are connecting. However,
when setting up the multi-base, the broadcast feature may not be
available due to the coverage range. In that case, you can use the
function of “Broadcast through PBX”
to broadcast
.
2. From an administrator handset (Handset 10 or 11), press
MENU
(Right) soft key.
3.
Press number
9
, this will enter administration menu.
4.
Press number
2
, handset enters Line setting menu.
a.
Enter Base ID(00~07) to access base.
b.
Press
1
to enter Broadcast setting
i. Press or to select L3 or L4 (the status of setting
will be displayed on LCD)
ii. Press CHANGE to enter the setting mode, and the base ID
will be displayed on LCD.
iii. Press On (Left softkey) to enable the broadcast function.
Press Off (Right softkey) to disable the broadcast function.
iv. After setting broadcast, press On (Left softkey) to enable
the AA. Press Off (Right softkey) to disable the AA.
Re: L3 and L4 can be setting as two broadcast lines, repeated
above items for setting 2
nd
broadcast
line.
5. When calling through the line 3 or 4, the caller will be prompt ed
by the
greeting message to enter a t
wo
-
digit extension number