User Guide

Quick Installation Guide
Maximum data rates are based on draft IEEE 802.11ac and/or IEEE 802.11 standards. Actual
throughput and range may vary depending on many factors including environmental conditions,
distance between devices, radio interference in the operating environment, and mix of devices in
the network. Features and specications subject to change without notice. This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Trademarks and registered trademarks
are the property of their respective owners. For United States of America: Copyright ©2013 EnGenius
Technologies, Inc. All rights reserved.
Notes
Technical Support
Country of Purchase Service Center Service Information
North America
www.engeniuscanada.com
Canada
[e-mail]
Toll Free: ([phone]
Local: ([phone]
www.engeniustech.com
Los Angeles, USA
[e-mail]
Toll Free: ([phone]
Local: ([phone]
Central & South America
es.engeniustech.com
pg.engeniustech.com
Miami, USA
[e-mail]
Miami: ([phone]
Sao Paulo, Brazil: ([phone]
D.F, Mexico: ([phone]
Europe
www.engeniusnetworks.eu
Netherlands
[e-mail]
([phone]
Africa
CIS
Middle East
Russia
www.engenius-me.com
Dubai, UAE
[e-mail]
Toll Free:
U.A.E.: 800-EnGenius
800-364-364-87
General: ([phone]
Asia
Oceania
www.engeniustech.com.sg
Singapore
www.engeniustech.com.sg/e_warranty_form
[e-mail]
Toll Free:
Singapore: 1800 364 3648
Others
www.engeniusnetworks.com
Taiwan, R.O.C
[e-mail]
Package Contents
Wall Mounting The AP
Pole Mounting The AP
A) Connect one end of the Ethernet cable into the main LAN port (PoE)
of the Access Point and the other end to the AP Ethernet port on the
PoE injector.
B) Connect the Power Adapter to the DC-IN port of the PoE injector and
plug the other end in to an electrical outlet.
C) Connect the second Ethernet cable into the LAN port of the PoE injector
and the other end to the Ethernet port on the computer.
D) Screw on the provided antennas to the device as shown in illustration below.
Note: The Access Point supports both IEEE 802.3at PoE (Power over
Ethernet) or the included power Injector. You may use either one as the
power source. DO NOT use both at the same time.
A)ToconguretheAccessPoint,openawebbrowser.Intheaddressbar
ofthewebbrowser,enter192.168.1.1 and hit enter.
B)Aloginscreenwillappear.Bydefault,theusernameoftheAccessPoint
is admin and the password is admin. Enter the current username and
password of the Access Point and then click Login.
A) Thisdevicecanoperateinthefollowingmodes:AccessPoint,MeshandWDS.
B) Select the Operation Mode under “Network”, “Wireless” tab.
A) Markthefourlocationsofthemountingholesontheatmounting
surface.
B) Drilla37mmdeep8mmholeinthemarkingsandhammerthebolts
into the openings.
A) Placethelockandatwashersonthefourhexcapscrewsanddrive
the screws to attach bracket to the back of the Access Point.
B) DrivethefourroundheadscrewstoattachthePoleMountBracketto
the bracket.
C) Thread the open end of the Pole Strap through the two tabs on the
  PoleMountBracket.
D) LockandtightenPoleStraptosecurePoleMountBrackettothepole.
C) Placethelockandatwashersonthefourhexcapscrewsanddrive
the screws to attach bracket to the back of the Access Point.
D) Tightentheatwasherstosecurethebrackettothe
mounting surface.
C) Click on the Savebuttonafteryouhavemodiedthesetting.Clickthe
Changesbutton,thenclickApply button to apply all changes
you have made.
ENH900EXT | ENH1750EXT
version l.0
DualBand,LongRange
WirelessOutdoorAccessPoint
1
Connecting the Access Point
2
IP Address Conguration
3
Access Point Setup
4
Switching Modes
Minimum Requirements
+
Broadband Internet Service
(CableorDSLModem)
+
Internet Browser
(InternetExplorer,Safari,Firefox,Chrome)
Access Point Power Adapter2.4GHzDetachableAntennasx 3
5GHzDetachableAntennasx 3
Quick Installation
Guide
PoleMountingKit
WallMountingKit
Ground CablePoE Injector
To Computer
2.4 GHz
5 GHz
5 GHz
2.4 GHz
A
B
C
D
D
B
Horizontal Placement
Horizontal Placement
Horizontal Placement
Vertical Placement
A
A
A) Onceyourcomputerison,ensure
that your TCP/IP is set to On or
Enabled.OpenNetwork
Connections and then click Local
Area Connection. Select Internet
Protocol Version 4 (TCP/IPv4)
and then click on the Properties
button.
B) IfyourPCisalreadyonanetwork,
ensure that you have set it to a
Static IP Address on the interface.
  (Example:192.168.1.10andthe
  SubnetMaskaddressas
255.255.255.0.
*Yourmodelnumbermaybedierentinthewebbrowserinterface.