Installation Instructions

ManualsBrandsEngenius ManualsOtherEWS360AP

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com

Disclaimer: Information may be subject to changes without prior notication.

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

EWS360AP

Package contents

- Managed indoor access point

- Power adapter

- RJ-45 Ethernet cable

- Mounting bracket

- Mounting kit

- T-Rail mounting kit

Minimum requirements

- Broadband Internet service (Cable or DSL modem)

- Internet browser (Internet Explorer, Safari, Firefox, Chrome)

- EnGenius wireless management L2 switch (To use with EWS-series

management switches)

Connecting the access point

Step 1: Connect one end of the Ethernet cable into an Ethernet port on the front

panel of the EnGenius wireless management switch and the other end to the

Ethernet port on the computer.

Step 2: Connect another Ethernet cable into the LAN port of the managed

access point and the other end to the Ethernet port on the wireless management

switch. With the wireless management switches, the managed access point is

able to obtain proper assigned IP address for further configurations.

IP Adress configuration

Step 1: Once your computer is on, ensure that your

TCP/IP is set to ‘On’ or ‘Enabled’. Open ‘Network

Connections’ and then click ‘Local Area Connection’.

Select ‘Internet Protocol Version 4’ (TCP/IPv4).

Step 2: If your computer is already on a network,

ensure that you have set it to a static IP address on

the interface. (Example: 192.168.1.10 and the

subnet mask address as 255.255.255.0.).

Management switch setup

Step 1: Open a web browser on your computer.

In the adress bar of the web browser, typ in 192.168.0.239 and choose enter.

Step 2: A login screen will appear. By default, username is admin and the

password is password. Enter the current username and password of the

wireless management switch and then click ‘Login’.

Step 3: The EnGenius wireless management switch user interface will appear.

Make sure the controller state is set to ‘Enabled’.

Summary of content (4 pages)

PAGE 1
EWS360AP Package contents - Managed indoor access point - Power adapter - RJ-45 Ethernet cable - Mounting bracket - Mounting kit - T-Rail mounting kit Quick Installation Guide IP Adress configuration Step 1: Once your computer is on, ensure that your TCP/IP is set to ‘On’ or ‘Enabled’. Open ‘Network Connections’ and then click ‘Local Area Connection’. Select ‘Internet Protocol Version 4’ (TCP/IPv4).
PAGE 2
EWS360AP Quick Installation Guide Adding managed access point (Through EnGenius wireless management switch GUI) Step 1: All managed access point(s) connected to the same network as the wireless management switch will appear on the right side of the screen, under the access point ‘under approval’ list. Locate and select the managed access point by checking the box and click ‘Allow’ to manage the device.
PAGE 3
EWS360AP Mounting the access point The access point can be ceiling mounted or wall mounted depending on the setup. To attach the access point to a ceiling or wall using the mounting bracket: Quick Installation Guide To attach the access point to a ceiling using T-Rail connectors: Step 1: Attach the T-Rail connectors to the bottom cover of the access point using the provided short screws. Use appropriate size T-rail connectors (15/16” or 9/16”).
PAGE 4
EWS360AP Quick Installation Guide Stand-alone access point Installation Connecting the access point Step 1: Connect one end of the Ethernet cable into the LAN port of the access point and the other end to the Ethernet port on the computer. Step 2: Connect the power adapter to the DC-IN port of the access point and plug the other end into an electrical outlet. Note: The access point supports both IEEE802.3at PoE (Power-over-Ethernet) or the included power adapter.