Installation Instructions

ManualsBrandsEngenius ManualsOtherEWS510AP

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com

Disclaimer: Information may be subject to changes without prior notication.

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

EWS510AP

Package contents

- Managed indoor access point

- Power adapter

- RJ-45 Ethernet cable

- Mounting bracket

- Mounting kit

- T-Rail mounting kit

Minimum requirements

- Broadband Internet service (Cable or DSL modem)

- Internet browser (Internet Explorer, Safari, Firefox, Chrome)

- EnGenius wireless management L2 switch (To use with EWS-series

management switches)

Connecting the access point

Step 1: Connect one end of a RJ-45 Ethernet cable to the PoE In (LAN/Uplink)

port on the rear of the access point.

Note: DO NOT connect a PoE injector to any of the four access ports on the

front as this could cause damage to the device.

Step 2: Connect the other end of the cable to a PoE Ethernet switch or the PoE

‘PoE Out’-port on the PoE injector.

Step 3: Using another RJ-45 Ethernet cable, connect one end to the Ethernet port

on the computer, and connect the other end to another port on the PoE Ethernet

switch or to the ‘Data In’-port on the PoE injector.

Step 4: Verify that the Power LED on the access point is steady orange.

Note: The access point supports both IEEE 802.3af/at PoE

(Power-over-Ethernet) or an optional DC power adapter (sold separately). You

may use either one as the power source. DO NOT use both at the same time.

IP adress configuration

Step 1: Once your computer is on, ensure that your

TCP/IP is set to ‘On’ or ‘Enabled’. ‘Open Network

Connections’ and then click ‘Local Area Connection’.

Select ‘Internet Protocol version 4 (TCP/IPv4)’.

Step 2: If your computer is already on a network,

ensure that you have set it to a static IP address on

the interface. (Example: 192.168.1.10 and the

subnet mask address as 255.255.255.0.)

Management switch setup

Step 1: Open a web browser on your computer.

In the adress bar of the web browser, typ in 192.168.1.1 and choose Enter.

Step 2: A login screen will appear. By default, the username is admin and the

password is admin. Enter the current username and password of the

wireless management switch and then click ‘Login’.

Step 3: The EnGenius wireless management switch user interface will appear.

This device can operate in access point mode.

Summary of content (3 pages)

PAGE 1
EWS510AP Package contents - Managed indoor access point - Power adapter - RJ-45 Ethernet cable - Mounting bracket - Mounting kit - T-Rail mounting kit Quick Installation Guide IP adress configuration Step 1: Once your computer is on, ensure that your TCP/IP is set to ‘On’ or ‘Enabled’. ‘Open Network Connections’ and then click ‘Local Area Connection’. Select ‘Internet Protocol version 4 (TCP/IPv4)’.
PAGE 2
EWS510AP Mounting the access point This access point is designed to be mounted on a wall plate or electrical outlet box. Quick Installation Guide Step 5: Hook the two tabs on the bottom of the bracket into the slots on the bottom of the access point, and slide the access point down gently until it holds in place. Step 1: Remove the cover of the wall plate. Step 2: Gently pull the required cables through the center of the mounting bracket.
PAGE 3
EWS510AP Quick Installation Guide Connecting using the 110 Punch-down block The 110 punch-down block can be used to connect the access point to the network instead of the RJ-45 connector. Note: DO NOT connect to both the punch-down block and the PoE (LAN/ Uplink) port to the network at a same time. EnGenius Europe | Veldzigt 28, 3454 PW De Meern, Netherlands | 0900-WIFIABC | www.wifiabc.com Disclaimer: Information may be subject to changes without prior notification. Follow us https://www.linkedin.