Owner's Manual

ManualsBrandsEngland's Stove Works ManualsStove25-PI

INSTALLATION & OPERATION INSTRUCTIONS

MODEL NUMBERS 25-PI , 55-SHP20 and 55-TRP20

Thank you for purchasing this product from a fine line of heating equipment. We wish you many

years of safe heating pleasure with your new heating appliance.

Save These Instructions.

NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER.

CONTACT CUSTOMER SERVICE @ 1-800-245-6489.

Please Note the Following Precautionary Statements:

THIS PELLET INSERT IS NOT APPROVED FOR MOBILE HOME INSTALLATION.

FOR MASONRY FIREPLACE INSTALLATION ONLY!

NOTE: WE DO NOT RECOMMEND PELLET STOVES AS YOUR ONLY SOURCE OF HEAT.

CAUTION: Please read this entire manual before installation and use of this

pellet fuel burning room heater.

Keep children, furniture, fixtures and all combustibles away from any heating appliance.

WARNING: USE OF OUTSIDE AIR IS MANDATORY WITH THIS UNIT.

DO NOT OPERATE UNIT WITH HOPPER OPEN. LID MUST BE SHUT AND TIGHTLY SECURED.

DO NOT OPERATE WITH DOOR OPEN, OPEN DOOR ONLY WHEN LIGHTING.

SAFETY NOTICE

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,

BODILY INJURY OR EVEN DEATH. FOR YOUR SAFETY AND PROTECTION, FOLLOW ALL

THE INSTALLATION INSTRUCTIONS. CONTACT YOUR LOCAL BUILDING OR FIRE

OFFICIALS FOR RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS

(INCLUDING PERMITS) IN YOUR AREA.

Do not allow paint, chemicals or construction dust on or near your unit. Do not allow liquid or ANY foreign

materials on or inside your unit. Shut your unit down and cover it when painting, construction or similar activity is

taking place. Wipe and clean your unit after any construction is done in your home, or if any foreign material gets

on or inside your unit. You may also need to remove the rear and side cover plates to your unit (unplug unit first)

and vacuum and clean the motors and inside of your unit.

Questions? Need Parts or Accessories? www.englandsstoveworks.com

Rev. 12/03

England’s Stove Works highly recommends the use of smoke detectors and

Carbon Monoxide detectors with any hearth product, including this unit. Follow all

manufacturer’s instructions when using smoke or Carbon Monoxide detectors.

Summary of content (23 pages)

PAGE 1
INSTALLATION & OPERATION INSTRUCTIONS MODEL NUMBERS 25-PI , 55-SHP20 and 55-TRP20 Thank you for purchasing this product from a fine line of heating equipment. We wish you many years of safe heating pleasure with your new heating appliance. Save These Instructions. NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489. Please Note the Following Precautionary Statements: THIS PELLET INSERT IS NOT APPROVED FOR MOBILE HOME INSTALLATION.
PAGE 2
NOTE: The first part of this manual covers Operating Instructions for the insert model as well as the freestanding models. For instructions pertaining to Installation of the insert models, see the last part of this manual. IMPORTANT INFORMATION: 1. Check local installation codes for your area. Call your Homeowner’s Insurance representative for inspection of your stove’s installation. 2. Read and comply with the instructions in this manual. 3.
PAGE 3
15. Do not allow paint, chemicals or construction dust on or near your unit. Do not allow liquid or ANY foreign materials on or inside your unit. Shut your unit down and cover it when painting, construction or similar activity is taking place. Wipe and clean your unit after any construction is done in your home, or if any foreign material gets on or inside your unit.
PAGE 4
Proper Impingement (Baffle) Plate Placement in Pellet Stove Firebox Occasionally in shipping, the impingement (baffle) plate may shift out of its proper position. If this is the case with your stove, follow these instructions to return the plate to its proper position. 1. Remove the plate from the stove, holding the plate by its tab handle, with the cutout notch facing upwards. 2.
PAGE 5
FLUE SYSTEM (also see rear of manual for inserts) Caution: Follow the pipe manufacturer’s installation instructions and directions for passing through combustible walls and ceilings. Check local codes in your area. NOTE: See the installation drawing later in this manual (Illustration 1). This unit is equipped with a negative draft system that pulls combustion air through the burn pot and pushes the exhaust air out of the dwelling.
PAGE 6
Existing Flue System If you are replacing a wood stove with a pellet unit the chimney or pipe should be thoroughly cleaned before proceeding with the installation. The flue system should be either masonry or a UL approved pre-manufactured Class A flue system. The flue thimble should be either six inches (6”) or eight inches (8”) and the proper reducer (6” to 3” or 8” to 3”) can be purchased at your local dealer.
PAGE 7
Freestanding Pellet Installation (NOTE: See last part of manual for Insert Installation) Caution: Follow the pipe manufacturer’s installation instructions and directions for passing through combustible walls and ceilings. Check local codes in your area. Illustration 1 Must have minimum 3” adapter before tee for longer run. For shorter run (such as Masonry Connection below), tee alone is acceptable. Our Part AC-3000 is acceptable for through-the-wall installation. Masonry Connection 1. 2. 3. 4. 5. 6.
PAGE 8
OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE WITH THE DOOR OPEN; OPEN DOOR ONLY WHEN LIGHTING. Do not burn trash (paper bags, etc.) in this unit. This stove has an induced draft system and is designed to operate continuously, as frequent shutdown is not required. The digital control board operates the unit with a time delay-relay system; this system controls the top auger feed rate by operating for a predetermined number of seconds while the bottom auger runs constantly.
PAGE 9
SHUT DOWN PROCEDURE WARNING: NEVER SHUT DOWN THIS UNIT BY UNPLUGGING IT FROM THE POWER SOURCE. Refer to the following instructions: Press the “OFF” touch pad to put the stove in the shut down mode. At this time the red light above the pad will illuminate. The instant this is done the top auger will stop feeding pellets to the bottom auger, but the room air blower, exhaust blower and the bottom auger will continue to operate.
PAGE 10
Combustion Blower Failure If the combustion (exhaust) blower should fail on this unit the Vacuum Shut Down Switch will automatically stop the stove. This will shut your unit completely off, and there will be an “E” code in the “Heat Range” window on the control board. At this point you will need to contact Customer Service at (800) 245-6489. NOTE: It is very important for the unit to be vented properly (outside air hook-up), as the natural draft is needed to clear the smoke from the stove.
PAGE 11
The exhaust venting system should be inspected at least once every year to determine if cleaning is necessary. MAINTENANCE CAUTION: UNPLUG THE UNIT PRIOR TO ANY SERVICE WORK. SEE EXPLODED DIAGRAM (ILLUSTRATION 4) FOR PARTS REFERENCE Note: To do any service on this unit the rear access sheet metal panel must be removed. Eight (8) screws hold this panel to the rear of the stove. Parts Orders: (800) 516-3636 www.englandsstoveworks.
PAGE 12
you may have to scrape the old cement from the door channel. Once the cement and gasket have been added the door should be closed and latched for twenty-four hours to allow the cement to harden. If you are replacing the window gasket (Part #AC-GGK), the new gasket will already have adhesive on one side. Remove the paper on the adhesive side and place the gasket around the outside edge of the glass by forming a “U” with your fingers and placing the gasket around the glass.
PAGE 13
Low Burn: Medium Low: Medium High: High Burn: Recommended Heat Ranges: Heat Range setting: 1 Room Air Blower setting: Heat Range setting: 2 – 3 Room Air Blower setting: Heat Range setting: 5 – 8 Room Air Blower setting: Heat Range setting: 9 Room Air Blower setting: * NOTE: Blower Speed should match Heat Range. CAUTION: NOTE: The bottom 3 buttons are pre-set at the factory and do not need adjustment. Call Service at (800) 245-6489 if you have questions or problems.
PAGE 14
CONTROL BOARD The control board (Part #PU-CB98) is a digital read-out board. This board offers a wide variety of settings to operate the unit. The bottom three control buttons are preset at the factory and should not require any changes on start-up of the unit. This part can be removed from the unit by loosening the two outside screws and pulling the board back to the inside of the stove. The rear access panel should be removed prior to removing the control board. A 4-amp fuse is used on this control board.
PAGE 15
REPLACEMENT PARTS AND OPTIONS AC-GGK Glass Gasket Kit (gasket only, no glass) AC-DGKC Door Gasket Kit (#2 on diagram) AC-114 Brass Louvers (#26 on diagram) (2001 and later Models; for earlier models call 800-245-6489 for AC-112 louvers) AC-G9 9” x 9” Glass with Gasket (#3 on diagram) AC-SH Door Spring Handle AC-MCSP Hi-Temperature Charcoal Paint PU-AMS Auger Motor Support Gasket PU-047040 1 RPM Auger Motor Assembly (#18 on diagram) PU-BP98 Burn Pot Assembly (#’s 5 and 11 on diagram, call
PAGE 16
INSTALLATION INSTRUCTIONS FOR THE PELLET INSERTS MODEL NUMBERS 25-PI , 55-SHP20 and 55-TRP20 IMPORTANT NOTE: These pages cover installation instructions for the Pellet Insert. For all other operating instructions, refer to the sections previous to this. THIS PELLET INSERT IS NOT APPROVED FOR MOBILE HOME INSTALLATION. FOR MASONRY FIREPLACE INSTALLATION ONLY. NOTICE: The internal structure of the insert, including the electrical and mechanical designs, is the same as the freestanding pellet units.
PAGE 17
3. 4. 5. 6. 7. 8. accident resulting from an insert being installed on a hearth constructed of a combustible material. Inspect your fireplace flue liner to be sure it is free of any obstructions and in good working condition. Remove the existing damper from the fireplace. If this cannot be done, open the damper and secure it so it will not close accidentally. Place the insert on the hearth and slide it about one-third of the way into the opening.
PAGE 18
PAGE 19
PAGE 20
Pellet Stove Exploded View Illustration 4
PAGE 21
TROUBLE-SHOOTING GUIDE WARNING: TO AVOID ELECTRICAL SHOCK ALWAYS DISCONNECT THE UNIT FROM THE POWER SOURCE BEFORE ATTEMPTING ANY REPAIR. IF THIS GUIDE DOES NOT CORRECT THE PROBLEM CALL YOUR LOCAL DEALER, OR OUR CUSTOMER SERVICE AT 1-800-245-6489. . Problem 1. Auger not turning Cause 1. Loose set screw 2. Bad gear motor 3. Foreign matter in auger 4. Vacuum sensor (Top Auger) Solution 1. Tighten setscrew on collar 2. Replace auger motor 3. Remove pellets and object 4. Check exhaust blower 2.
PAGE 22
Have this information on hand if you phone the factory or your dealer regarding this product. Retain for your files: Model Number __________________________ Date of Purchase ________________________ Date of Manufacture _________________ Serial #_____________________ LIMITED 5 YEAR WARRANTY FROM THE DATE OF PURCHASE TO THE ORIGINAL OWNER The manufacturer extends the following warranties: Five Year Period: 1. Carbon steel and welded seams in the firebox are covered for 5 years against splitting. 2.
PAGE 23
WARRANTY REGISTRATION Purchased by (Name) ______________________________________________ Address _________________________________________________________ City ________________________ State __________ Zip _________________ Telephone _______________________________________________________ Email (Optional) ___________________________________________________ DEALER INFORMATION Purchased From (Dealer) ___________________________________________ Address _________________________________________________________