Installation Guide

ManualsBrandsEnglander ManualsHeating, Ventilation, and Air ConditioningImperial 2,200 sq. ft. Pellet Stove

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING CLEANING

THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT,

OR DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH ANY

QUESTIONS.

YEARLYMAINTENANCE

CradleRemovalandCleaning

Thecradleneedstoberemovedyearly,tobecleanedandtoreplacethecradlegasket.

Toremovethecradle:

 First,removethebackpanelfromthestove(usinga

”socket).

 Lookingintothestovefromthefront,loosenthetwoboltsinthefrontthatholdthecradle,

thenremovetheigniter(seepage36).Aftertheigniterisremoved,finishlooseningthebolts

andliftthecradleoutofthestove.

 Cleanoutthecradleandremovetheoldgasket(itmaybenecessarytoscrapethegasketoff).

 Replacethegasket,usinganadhesive(high‐temp.siliconecanbeorderedwiththispart).

 Placethecradlebackintothestoveandtightentheboltsbyhanduntiltheyaretouchingthe

cradle.Then,usea½”sockettotightenuntilthegasketismated.Theboltsdonotneedtogo

allthewayin.*Note:Whentighteningthebolts,tighteneachonealittleatatime.*



CleaningPelletFinesfromtheHopperandAuger

Dependingonthetypeandqualityofpelletsburnedinthestove,someaccumulationofpelletfines

anddustispossibleinthehopper.Thelowestpartoftheauger,nearthebackofthestove,iswhere

mostfineswillaccumulate.Withthestoveoff,unplugged,completelycoolandwiththehopper

empty,useautilityvacuumtoremovethefinesfromtheaugertube.Ifthefinescannotberemoved

fromthetopofthehopper:

 Removethebackpanel,usinga

”sockettoremovethescrews.

 Locatetheaugermotorassemblyatthemiddlerearofthestove,andonceitisfound,findthe

twosetscrewsoneithersideofthecastironmountingcollar.

 Usinga

”allenwrench,loosenthesetscrewoneithersideoftheaugermountingcollar.

 Withautilityvacuuminhand,lettheaugerassemblyslideoutoftheaugertubejustenoughso

thatthevacuumcanbeusedtoremoveanyfinesfromthisarea.

Reinstalltheaugerassemblyandtightenthetwosetscrews;reinstallthebackpanel,beingcertainto

tightentheretainingscrewsontherearofthestove.



CheckingGaskets



Anairtightsealatthedooropeningsandhopperlidopeningiscrucialtoproperstoveperformance.

Anyairleaksattheseareascannotonlycauseadirty,inefficientburnbutcanalsoposeaserious

safetythreat.Becauseofthis,gasketsshouldalwaysbemaintainedingoodcondition,

andreplaced

annually,orsoonerifnecessary.Gaskettightnesscanbecheckedusingthe“dollar‐bill”method:

 Placeadollarbillbetweenthegasketandthestovebody(atthelocationwherethegasket

meetsthestove).

 Tightenthelatchingmechanismdownandattempttopullthedollarbillout.Ifthedollarbill

slidesinandouteasily,thegasketneedstobereplaced.Thistestshouldberepeatedaround

theentiregasketperimeter,asgasketswillsometimessealtightlyononeside,butwillbeworn



andsealpoorlyonanotherside

.