DIGITAL VIDEO RECORDER Quick Start Guide V1.0.3 www.enssecurity.
Foreword Welcome Thank you for purchasing our Digital Video Recorder (DVR). This Quick Start Guide (hereinafter referred to be "the Guide") will help you become familiar with our DVR in a short time. Please read the Guide carefully before starting using your DVR and properly keep it for future reference. Important Safeguards and Warnings Operation Requirement Do not place or install the Device in a place exposed to sunlight or near the heat source. Keep the Device away from dampness, dust or soot.
Signal Words Meaning Indicates a potential risk which, if not avoided, could result in property damage, data loss, lower performance, or unpredictable result. Provides additional information as the emphasis and supplement to the text. Privacy Protection Notice As the device user or data controller, you might collect personal data of others' such as face, fingerprints, car plate number, Email address, phone number, GPS and so on.
Table of Contents Foreword .................................................................................................................................................... I 1 Quick Start ............................................................................................................................................. 1 Unpacking the Accessories ........................................................................................................... 1 Checking the Components.................
1 Quick Start The actual appearance or quantity might be different depending on the model you purchased. Unpacking the Accessories Checking the Components When you receive the DVR, please check against the following checking list. If any of the items are missing or damaged, contact the local retailer or after-sales engineer immediately. Sequence 1 Checking items Requirement Appearance No obvious damage. Packing materials No broken or distorted positions that could be caused by hit.
1. Remove the screws to take off the cover. 2. Fix the screws on the HDD but do not fasten them. 3. Put the HDD onto the DVR. 4. Turn the DVR to see the 5. Use the HDD cable and 6. Put back the cover and back side of it. Aim the power cable to connect screws of the HDD at the HDD and mainboard. fasten the screws. holes on the back of the DVR, and then fasten the screws. Booting up Ensure the input voltage corresponds to the power requirement of the DVR. Connect the DVR to a display.
2 The Grand Tour for Rear Panel The following figure shows the rear panel of model with 4 video input ports (as an example). Rear panel Table 2-1 Port description No. Port Name No. Port Name No.
3 Local Configurations The interfaces in the Guide are used for introducing the operations and only for reference. The actual product shall govern. For details about operations of the DVR, see User’s Manual. To enter the Main Menu, right-click on the live view screen to display the shortcut menu, and then click Main Menu and login the system. Initializing DVR When booting up for the first time, the Device Initialization interface is displayed, see Figure 3-1.
Password Protection Mode Description Email Address In the Email Address box, enter an email address for password reset. In case you forgot password, enter the security code that you will get from this reserved email address to reset the password of admin. Security Questions Configure the security questions and answers. In case you forgot password, enter the answers to the questions can make you reset the password.
Recorded video Configuring P2P Settings You can add the DVR into your cell phone client or the platform to manage. For details, please refer to the P2P operation manual. Make sure the DVR is connected into the Internet, and if yes, in the Status box of the P2P interface, it shows Online. 3.4.1 Entering P2P Interface Select Main Menu > NETWORK > P2P, the P2P interface is displayed. See Figure 3-4.
P2P interface Enable the P2P function. Click Apply. You can start adding the DVR into Cell Phone Client or the platform. 3.4.2 Adding DVR into Cell Phone Client To use P2P function, take adding wired device into Cell Phone Client as an example. Use your cell phone to scan the QR code under Cell Phone Client to download the application. Open the application and tap Tap Device Manager > , the menu is displayed. >Add Device, the Add Device interface is displayed. See Figure 3-5.
Figure 3-5 Add device Figure 3-6 Live view Logout On the top right of the Main Menu interface or any interface after you have entered the Main Menu, click . Select Logout, you will log out the DVR. Select Reboot, the DVR will be rebooted. Select Shutdown, the DVR will be turned off. You can also press the power button on the DVR to turn it off.
4 Web Login Open the browser, enter the IP address of the DVR, and then press Enter key. The Login in dialog box is displayed. See Figure 4-1. Properly enter the user name and password to login the web. For details, see User’s Manual. Login Device initialization is required at the first login. The default administrator account is admin. The password is the one that was configured during initializing settings.
