Single-Port Power Over Ethernet Adapter User’s Guide P/N 9034273
Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice.
Documentation URL: http://www.enterasys.com/support/manuals Documentacion URL: http://www.enterasys.com/support/manuals Dokumentation im Internet: http://www.enterasys.com/support/manuals Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device complies with Part 15 of the FCC rules.
Clase A. Aviso de ITE ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas. Klasse A ITE Anmerkung WARNHINWEIS: Dieses Produkt zählt zur Klasse A ( Industriebereich ). In Wohnbereichen kann es hierdurch zu Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden. Product Safety This product complies with the following: UL 60950, CSA C22.2 No.
Hazardous Substances This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment. European Waste Electrical and Electronic Equipment (WEEE) Notice In accordance with Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment (WEEE): 1.
VCCI Notice This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. BSMI EMC Statement — Taiwan This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Declaration of Conformity Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer’s Name: Manufacturer’s Address: European Representative Address: Conformance to Directive(s)/ Product Standards: Equipment Type/Environment: Enterasys Networks, Inc. 50 Minuteman Road Andover, MA 01810 USA Enterasys Networks, Ltd.
ONE-YEAR LIMITED WARRANTY Enterasys Networks warrants to the original consumer or purchaser that each of its products, and all components thereof, will be free from defects in material and/or workmanship for a period of one year from the original factory shipment date. Any warranty hereunder is extended to the original consumer or purchaser and is not assignable.
Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
2. RESTRICTIONS. Except as otherwise authorized in writing by Enterasys, You may not, nor may You permit any third party to: (i) Reverse engineer, decompile, disassemble or modify the Program, in whole or in part, including for reasons of error correction or interoperability, except to the extent expressly permitted by applicable law and to the extent the parties shall not be permitted by that applicable law, such rights are expressly excluded.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S.
7. LIMITATION OF LIABILITY. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law. 11. ASSIGNMENT.
Contents About This Guide Purpose ......................................................................................... xv Who Should Use This Guide ......................................................... xv Document Conventions ................................................................ xvi Getting Help ................................................................................ xvii Chapter 1: Introduction Functions and Features ..............................................................
Figures 2-1 BL-69551ENT Schematic Block Diagram ...................... 2-3 Tables 3-1 A-1 xiv Troubleshooting Checklist............................................... 3-1 Physical and Mechanical Specifications .........................
About This Guide Purpose This document provides information and procedures on hardware installation, setup, configuration, and management of the Enterasys Networks single‐port 15.4W Power Over Ethernet Adapter (BL‐69551ENT). Who Should Use This Guide Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.
Document Conventions • A working knowledge of basic electronics and mechanical assembly. • An understanding of local operating and troubleshooting procedures. • An understanding of related local building codes. Document Conventions The following conventions are used in this guide: Note: Calls the reader’s attention to any item of information that may be of special importance. Caution: Contains information essential to avoid damage to the equipment.
Getting Help Getting Help For additional support related to the modules or this document, contact Enterasys Networks using one of the following methods: World Wide Web www.enterasys.com/services/support/ Phone 1-800-872-8440 (toll-free in U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/services/support/contact/ Internet mail support@enterasys.com To expedite your message, type [other] in the subject line.
Getting Help xviii • A description of your network environment (layout, cable type, etc.) • Network load and frame size at the time of trouble (if known) • The device history (i.e., have you returned the device before, is this a recurring problem, etc.
1 Introduction Functions and Features The Enterasys BL‐69551ENT Single‐Port Power Over Ethernet Adapter supports applications in which AC power is difficult to access, such as VoIP phones, wireless LAN access points or Internet security cameras. The Single‐Port Power Over Ethernet Adapter acts as a “patch panel” and adds ~48 VDC to unused (non‐data) wires in a standard Category 5, 5e, or 6 Ethernet cable. The BL‐69551ENT delivers both data and power over a single standard Ethernet cable.
Functions and Features • Removable Power Cord w/IEC Connector • IOL Test Report • Full Protection OTP, OCP, OVP • Data and Power carried over one Ethernet Cable • AC Disconnect (Optional) • Integrated Mounting brackets Over Voltage/Current, Short Circuit Protection Outputs equipped with short circuit protection and overload protection as per 802.3af specification. The output can be shorted permanently without damage.
2 Installation and Connection Electrical Hazard: Only qualified personnel should install or service this unit. Riesgo Eléctrico: Solamente personal capacitado debe de instalar o darle servicio a esta unida. Elektrischer Gefahrenhinweis: Installationen oder Servicearbeiten sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.
Technical Considerations Technical Considerations Before you mount the adapter to a fixed location, consider the following: • Determine optimal placement. • Collect and document network information as required. • Ensure the cable length from the Ethernet network source to the powered device does not exceed 100 meters. Note: The unit is not a repeater and does not amplify the Ethernet data signal.
Powering Up Powering Up Simply plug one end of the power cord or power supply into the unit, and the other end into a grounded AC power source. Units are typically connected to a power strip or other power outlet that may be cycled on and off. An uninterruptible power supply (UPS) may be used.
Powering Up Detection Sequence Once a compliant load is attached to the output RJ45 connector, the green “CONNECT” LED will illuminate. Should the load be non‐compliant, then the LEDs will blink a code signifying the cause for non‐detection. Detection Failure Codes 1. Incorrect resistive signature – The green “CONNECT” and red “FAULT” LEDs will blink 3 times. 2. Incorrect capacitive signature – The green “ON” LED will blink 3 times. 3.
3 Troubleshooting Checklist Refer to Table 3‐1 for a checklist of problems and recommended actions to resolve the problem. If additional support is needed, refer to “Getting Help” on page xvii. Table 3-1 Troubleshooting Checklist Problem Recommended Action Unit is plugged into the Enterasys Single-Port Power Over Ethernet Adapter, but main power indicator is “off.” Verify the use of a good AC cable with a good ground connection.
Checklist Table 3-1 Troubleshooting Checklist (continued) Problem Recommended Action The Single-Port Power Over Ethernet Adapter operates but one of the powered devices does not work. Verify that you are using a standard UTP Cat. 5 or greater cable, including all 8 wires (4 pairs.) Try using a different Ethernet cable. If it works, there is probably a faulty connection over the long cable, or a bad RJ45 connection. Insure that your load device works with an 802.
Checklist Table 3-1 Troubleshooting Checklist (continued) Problem Recommended Action The Single-Port Power Over Ethernet Adapter operates and the load device works, but there is no data link. Verify that the indicator for the port is “on.” Verify that the Single-Port Power Over Ethernet Adapter is connected to the Ethernet network with a good connection. Verify that the Ethernet cable is Category 5 or greater, and is less than 100 meters in length from the Ethernet source to the load.
Checklist 3-4 Troubleshooting
A Hardware Specifications This appendix lists the BL‐69551ENT Single‐Port Power Over Ethernet Adapter hardware and electrical specifications. Regulatory Compliance Standards This equipment meets the following safety and electromagnetic compatibility (EMC) requirements: Safety UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, IEC 60950 Electromagnetic Compatability (EMC) 47 CFR Parts 2 and 15, CSA C108.
Safety Approvals Safety Approvals The equipment meets the following safety approvals: • cUL/UL • CCC • FCC • CE • TUV • Output Specifications Model DC Output Voltage BL-69551ENT 48V Load Min. Max. 0A 0.35A Regulation Line Load ±4% Ripple and Noise* Vp-p* <500Hz 0.5 500Hz-150KHz 0.15 150KHz-500KHz 0.15 500KHz-1MHz 0.1 *. As per IEEE802.3af Table 33-5. For Legacy detection or AC disconnect please contact the factory. Enterasys Networks is not responsible for any error and change.
Physical/Environmental Specifications Physical/Environmental Specifications Table A‐1 provides physical and mechanical specifications for the Single‐Port Power Over Ethernet Adapter. Table A-1 Physical and Mechanical Specifications Item Specification Length: 140 mm (5.51 in.) Width: 65 mm (2.55 in.) Height: 36 mm (1.42 in.) Weight: 0.2 Kg (0.44 lb) Input: AC Input Voltage Range 90 to 264VAC AC Input Voltage Rating 100 to 240VAC AC Input Current 0.5A(RMS) max. for 90VAC 0.35A(RMS) max.
Physical/Environmental Specifications AC Inrush Current 15A(RMS) max. for 115VAC 20A(RMS) max. for 230VAC Output: Total Output Power 15.4W Efficiency 65% (typical) at Max. load, and 120VAC 60Hz Hold-up Time 16mS min. 120VAC and max. load Transient O/P Voltage Protection 60V max.
Physical/Environmental Specifications Isolation Test Primary to Secondary: 3000VAC for 1 minute 10mA Primary to F.G.: 1500VAC for 1 minute Output to F.G.: 1500VAC Immunity EN50082-1 ESD: RS: EFT: Surge: CS: Voltage Dips Harmonic: EN61000‐4‐2. Level 3 EN61000‐4‐3. Level 2 EN61000‐4‐4. Level 2 EN61000‐4‐5. Level 3 EN61000‐4‐6.
Physical/Environmental Specifications A-6 Hardware Specifications
