7.
Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice.
Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
Electromagnetic Compatibility (EMC) This product complies with the following: 47 CFR Parts 2 and 15, CSA C108.8, 2004/108/EC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3. Compatibilidad Electromágnetica (EMC) Este producto de Enterasys cumple con lo siguiente: 47 CFR Partes 2 y 15, CSA C108.8, 2004/108/EC, EN 55022, EN 55024, EN 61000‐3‐2, EN 61000‐3‐3, AS/NZS CISPR 22, VCCI V‐3.
ѻક䇈ᯢк䰘ӊ Supplement to Product Instructions 䚼ӊৡ⿄ (Parts) 䞥ሲ䚼ӊ (Metal Parts) ⬉䏃ഫ (Circuit Modules) ⬉㓚ঞ⬉㓚㒘ӊ (Cables & Cable Assemblies) ล᭭㘮ড়⠽䚼ӊ (Plastic and Polymeric parts) ⬉䏃ᓔ݇ (Circuit Breakers) ƻ˖ 䪙 3E ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) ⒈㘨㣃 ∲ 䬝 ݁Ӌ䫀 3%% +J &G &U h ƻ ƻ h ƻ ƻ h ƻ ƻ h ƻ ƻ h ƻ ƻ h ƻ ƻ ƻ ƻ ƻ ƻ ƻ h ƻ ƻ h h ƻ ƻ ⒈Ѡ㣃䝮 3%'( 㸼⼎䆹᳝↦᳝ᆇ⠽䋼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ䞣ഛ SJ/T 11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ Indicates that the concentration of the hazardous substance
VCCI Notice This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. BSMI EMC Statement — Taiwan This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Declaration of Conformity Application of Council Directive(s): Manufacturer’s Name: Manufacturer’s Address: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 2004/108/EC 2006/95/EC Enterasys Networks, Inc. 50 Minuteman Road Andover, MA 01810 USA Enterasys Networks, Ltd.
ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party.
8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys, and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program.
x
Contents About This Guide Who Should Use This Guide ............................................................................................................... xv How to Use This Guide ...................................................................................................................... xvi Related Documents ...........................................................................................................................
Appendix A: Specifications Matrix N5 Chassis ............................................................................................................................. A-2 7C205-1 System Power Supply Module ........................................................................................... A-3 N-POE-1200W Power Supply Module .............................................................................................. A-3 7C405 Fan Assembly ........................................................
A-7 A-8 Environmental Specifications ................................................................................................ A-6 Compliance Standards..........................................................................................................
xiv
About This Guide This guide lists the Enterasys Matrix® N5 7C105‐P features, options, specifications, and instructions to install the Matrix N5 7C105‐P chassis on a flat surface or in a standard 19‐inch equipment rack or cabinet. This guide also explains how to interpret the system status LEDs to facilitate troubleshooting when necessary, and also provides information on how to contact Enterasys Networks for additional help.
How to Use This Guide How to Use This Guide Read through this guide completely to familiarize yourself with its contents and to gain an understanding of the features and capabilities of the N5 chassis. A general working knowledge of data communications networks is helpful when setting up the chassis. To locate information concerning various subjects in this guide, refer to the following table: For information about... Refer to page...
Conventions Used in This Guide Conventions Used in This Guide The following conventions are used in this guide: Note: Calls the reader’s attention to any item of information that may be of special importance. Caution: Contains information essential to avoid damage to the equipment. Precaución: Contiene información esencial para prevenir dañar el equipo. Achtung: Verweißt auf wichtige Informationen zum Schutz gegen Beschädigungen.
Conventions Used in This Guide xviii Matrix N5 PoE Chassis (7C105-P) Installation Guide
1 Introduction This chapter provides a functional overview of the Enterasys Matrix N5 chassis and its features. Also covered in this chapter are the instructions on how to obtain additional help from Enterasys Networks, if needed. For information about... Refer to page...
Enterasys Matrix N5 Chassis 7C105-P Overview Enterasys Matrix N5 Chassis 7C105-P Overview The Enterasys Matrix N5 chassis provides five slots for a new advanced generation of Ethernet switch modules, the Enterasys Matrix DFE series modules. DFE modules installed in the 7C105‐P chassis operate as a system with a single IP address. The modular design of the chassis enables you to install the system and PoE power supplies, and modules from the front of the chassis for ease of maintenance.
Enterasys Matrix N5 Chassis 7C105-P Overview Figure 1-1 Enterasys Matrix N5 Chassis with One 7C205-1 AC Power Supply À 10 FAN STATUS Á È TOP - SLOT 5 SLOT 4 Ç SLOT 3 SLOT 2 BOTTOM - SLOT 1 Â AC ON 0 POWER FAN Ã LINE: 100-125V~12A 200-240V~6A 50/60Hz PS 2 PS 1 POE 1 POE 2 AC INLET 1 AC INLET 3 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz AC INLET 2 AC INLET 4 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz
Enterasys Matrix N5 Chassis Modules Enterasys Matrix N5 Chassis Modules The N5 chassis has five slots for the new Matrix DFE series modules with or without PoE capability. Note: The N5 chassis supports the DFE (Distributed Forwarding Engine) 7xxxxx or 4xxxxx series modules, but it does not support the older 6x1xx, 6x2xx, and 6x3xx series of modules. Do not mix 7xxxxx and 4xxxxx series modules in the same chassis.
Chassis Power Systems Auto-Ranging Power Supplies The 7C205‐1 power supply automatically adjusts to the input voltage and frequency, which allows for an input voltage of 100 to 220 Vac, and a frequency between 50 and 60 Hz. See the operating specifications in Appendix A. No additional adjustments are necessary. For installations in North America, a 20 A power cord is required. See “Connecting AC Power to 7C205‐1” on page 3‐13 for more details.
Chassis Power Systems • Provides power for up to five POE switch modules residing in the Enterasys Matrix N5 chassis. • Provides separate AC power inlet connectors for each N‐POE PSM installed. N-POE Power Supply Module (N-POE PSM) The N‐POE PSM features include the following: • Hot swappable capability as long as the total power needed does not exceed the power output capability of the remaining N‐POE PSMs in the N5 chassis. • Provides a maximum power output of 1200 W to PoE switch modules.
Power Classifications and Deployment Power Classifications and Deployment The number of N‐POE PSMs needed to power the PoE‐compliant PDs is dependent on their Power Classifications. Each N‐POE PSM can supply up to 1200 Watts of power. You can determine the number of power supplies needed by referring to Table 1‐1 and adding up the maximum power requirement according to the Power Classification rating (1 through 3) of each PD.
Power Classifications and Deployment Figure 1-2 Example of a Simple N-PoE Power Configuration À Á Â Ã Ä Å SLOT 4 SLOT 3 47X 4 SLOT 2 DFE 38X G R O U P 3 G R O U P 2 G R O U P 13X 1 11X G R O U P 1X TOP - SLOT 5 Æ 48X 36X 37X 26X 25X 35X 24X 23X 12 10 9 11 14X 8 7 4 4 6 3 3 5 2 2 12 X 1 GROUP COM CPU POE GROUP SELECT MGMT 1 7H4385-49 FAST ENET 2X OFFLINE/ RESET FAN STATUS BOTTOM - SLOT 1 AC ON 0 POWER FAN LINE: 100-125V~12A 200-240V~6A 50/60Hz P
Power Classifications and Deployment The PoE switch module manages the 48 Vdc output to the six PDs. In this example, assume that six of the PoE module 48 Vdc/data ports are devices connected to PDs with the following Class ratings: • One does not support PoE (no power) • One has no Class rating (Defaults to Class 0, 12.95 Watts maximum) • Two are Class 2 (6.49 Watts maximum x 2 = 12.98 Watts total) • One is Class 3 (12.95 Watts maximum) • One is Class 4 (defaults to 12.
Getting Help Getting Help For additional support related to the chassis or this document, contact Enterasys Networks using one of the following methods: World Wide Web www.enterasys.com/support/ Phone 1-800-872-8440 (toll-free in U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/services/support/contact/ Internet mail support@enterasys.com To expedite your message, please type [N-SERIES] in the subject line.
2 Installation Requirements and Guidelines Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. This chapter provides guidelines that should be followed when installing the 7C105‐P chassis. For information about... Refer to page...
Installation Site Guidelines . Warning: Install the Enterasys Matrix N5 chassis in a Restricted Access Location only. Access to the equipment by users must be restricted through the use of a tool or lock and key or other means of security and is controlled by the authority responsible for the location. Advertencia: Instalar el chasis Enterasys Matrix N5 en un lugar de Acceso Restringido.
Configuration Guidelines N‐POE‐1200W DC power supplies. Each AC outlet must have a reliable ground connection and be on an independently‐fused circuit, which can supply the current and voltage specified in “Matrix N5 Chassis” on page A‐2 and “7C205‐1 System Power Supply Module” on page A‐3. The outlets needed as per each model power supply are: – Two grounded AC power outlets, one for each of the two 7C205‐1 AC power supplies installed in the 7C105‐P chassis.
LANVIEW LEDs LANVIEW LEDs The following sections describe the LANVIEW LED indications for the following: • 7C205‐1 power supply module • N‐POE‐1200W power supply module • Fan assembly Power Supply (7C205-1) LEDs There are two LEDs on the 7C205‐1 power supply. Refer to Figure 2‐1 for the location of the power supply LEDs. Table 2‐1 describes the different states of the power supply LEDs under six different conditions. The power supplies are installed in chassis slots PS1 and PS2 of the chassis.
LANVIEW LEDs Table 2-1 Condition Power Supply (PS) LED Status Definitions PS1 PS2 Load PS1 LEDs PS2 LEDs POWER FAN POWER FAN 1 ON OFF Amber Green Red Red 2 OFF ON Red Red Amber Green 3 ON Out of chassis Green Green Off Off 4 Out of chassis ON Off Off Green Green 5 ON ON <50% Green Green Green Green 6 ON ON >50% Amber Green Amber Green PoE Power Supply (N-POE-1200W) LEDs There are two LEDs on the N‐POE‐1200W power supply module.
LANVIEW LEDs Fan Status LED Refer to Figure 2‐3 for the location of the Fan Status LED. Table 2‐3 describes the different states of the LED. Figure 2-3 Fan Status LED À FAN STATUS 1 Fan Status LED Table 2-3 Fan Status LED States and Their Definitions LED Color Status Green All fans are operating normally. Red One or more fan failures have occurred. When the Enterasys Matrix N5 is first powered up, the Fan Status LED will display red briefly, until the fans are operating at the proper speed.
3 Chassis Installation Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. This chapter describes how to install the Enterasys Matrix N5 chassis into a standard 19‐inch rack and install its modular power components. For information about... Refer to page...
Installation Site Requirement Installation Site Requirement The Matrix N5 7C105‐P chassis must be installed in a Restricted Access Location (RAL). This location should only be accessible by people that have been trained or are technically competent enough to be aware of potential risks of accessing the hazardous areas of the chassis. Locations such as a locked wiring closet or locked cabinet meet this requirement. Warning: Install the Enterasys Matrix N5 chassis in a Restricted Access Location only.
Unpacking the Chassis Figure 3-1 Unpacking the Enterasys Matrix N5 Chassis Â Ã Ä Á Å Æ Ç À Æ È Matrix N5 PoE Chassis (7C105-P) Installation Guide 3-3
Unpacking the Chassis 3. Remove and save the accessory package and any other documents, and cable from the top of the styrofoam cap. The accessory package contains: – Electrostatic Discharge (ESD) wrist strap – Installation documentation 4. Lift and remove the styrofoam cap from the top of the chassis. Save for reshipping, if necessary. 5. Open the top of the shipping bag covering the unit. 6. Pull the bag down around the skid. 7.
Unpacking the Power Supply Modules Unpacking the Power Supply Modules The 7C205‐1 and optional N‐POE‐1200W power supply modules are shipped in boxes separate from the chassis. To unpack a power supply, proceed as follows: 1. Unpack the power supply by removing it from the shipping box and sliding the two foam end caps off the unit. (Save the shipping box and materials in the event the unit must be reshipped.) 2. Verify the contents of the box using Table 3‐2 and Table 3‐3, as appropriate. 3.
Installing the Chassis Installing the Chassis The Matrix N5 7C105‐P chassis can be installed in a standard 48.26‐centimeter (19‐inch) equipment rack. Up to three N5 chassis chassis can be mounted in a standard 7‐foot high cabinet. Note: Allow at least 60 centimeters (24 inches) or more clearance in front and rear of the rack for chassis installation and maintenance. Caution: Read Chapter 2 before completing the following procedure to ensure that all installation guidelines are met.
Installing the Chassis Figure 3-2 Rack Mounting the Enterasys Matrix N5 chassis FAN STATUS À TOP - SLOT 5 SLOT 4 SLOT 3 SLOT 2 BOTTOM - SLOT 1 À AC ON 0 POWER FAN LINE: 100-125V~12A 200-240V~6A 50/60Hz PS 2 PS 1 POE 1 POE 2 AC INLET 1 AC INLET 3 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz AC INLET 2 AC INLET 4 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz CAUTION: THIS UNIT MAY HAVE MORE THAN ONE POWER SU
Installing the Chassis Figure 3-3 ESD Grounding Receptacle À FAN STATUS 1 ESD grounding receptacle Installing a 7C205-1 Power Supply You must install at least one 7C205‐1 in the N5 chassis for chassis power. One power supply provides sufficient power for a fully loaded chassis, but a second power supply can be installed to provide a redundant, load sharing power source. When you receive your N5 chassis, a coverplate will be in place over power supply slot PS2.
Installing the Chassis c. With the power supply properly inserted into the opening, carefully slide the supply forward until it is connected to the backplane. The front panel should be flush with the face of the N5 chassis. If significant resistance is encountered before the front panel is flush, remove and reinsert the power supply. Do not force the power supply into place. d.
Installing the Chassis Note: To install the DFE modules, refer to the module installation guide for the installation instructions. Before you power up the N5 chassis, it is recommended that you complete the installation of any optional N-POE-PSM-1200W power supplies, as applicable, and DFE modules. If you plan to install optional N‐POE‐1200W DC power supply modules, proceed to Installing Optional N‐POE PSMs (page 3‐10) for instructions.
Installing the Chassis To install the N‐POE PSMs, proceed as follows: Note: To reduce Electromagnetic Interference from the Enterasys Matrix N5 Chassis, ensure that both bay covers are installed during operation. 1. Refer to Figure 3‐5. Unscrew the two Phillips‐head captive‐cover screws to release the bay cover from the chassis bay where you plan to install an N‐POE PSM. (In this procedure, the left bay is used as an example.) Remove the bay cover and set it aside for now.
Installing the Chassis 5. Replace the bay cover removed in step 1. Caution: It is important to replace any bay cover removed during the installation to reduce Electromagnetic Interference from the chassis. Precaución: Para reducir la interferencia electromagnética del chasis, no olvide volver a colocar todas las tapas de los compartimentos que haya quitado durante el proceso de instalación. Note: If you need to remove a N-POE PSM, refer to “Replacement Procedures” on page 3-17 for instructions. 6.
Connecting AC Power to 7C205-1 Connecting AC Power to 7C205-1 To power up a 7C205‐1, refer to Figure 3‐7 and proceed as follows: Note: If two power supplies are installed, repeat the following procedure for each supply. For proper redundancy using two 7C205-1 power supplies, the power cord from each power supply must be connected to a dedicated 20-Ampere AC power circuit. 1. Plug one end of the power cord (supplied with the power supply) into the AC power socket on the front panel of the power supply.
Connecting AC Power to N-POE PSMs 4. Ensure that all fans in the fan assembly are operating properly. The fan status LED located at the top‐left front of the chassis will turn green when power is received from the power supply modules. For more information on the power supply LEDs (Power and Fan), refer to “LANVIEW LEDs” on page 2‐4. 5. If N‐POE PSMs have been installed, proceed to “Connecting AC Power to N‐POE PSMs”.
Troubleshooting the N-POE PSM Figure 3-8 AC Power Connections Ã Ä TOP - SLOT 5 SLOT 4 SLOT 3 SLOT 2 BOTTOM - SLOT 1 AC ON AC ON 0 POWER 0 FAN POWER FAN LINE: 100-125V~12A 200-240V~6A 50/60Hz LINE: 100-125V~12A 200-240V~6A 50/60Hz PS 2 PS 1 POE 1 POE 2 AC INLET 1 POE 3 AC INLET 3 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz AC INLET 2 AC INLET 4 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz CAUTION: TH
Troubleshooting the N-POE PSM Figure 3-9 N-POE PSM Status LEDs À Á TOP - SLOT 5 SLOT 4 SLOT 3 SLOT 2 BOTTOM - SLOT 1 AC ON AC ON 0 POWER 0 FAN POWER FAN LINE: 100-125V~12A 200-240V~6A 50/60Hz LINE: 100-125V~12A 200-240V~6A 50/60Hz PS 2 PS 1 POE 1 POE 2 AC INLET 1 POE 3 AC INLET 3 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz AC INLET 2 AC INLET 4 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz CAUTION: T
Replacement Procedures Replacement Procedures The following instructions describe how to: • remove a 7C205‐1, • remove N‐POE‐1200W, or • remove and install the fan assembly. Removing a 7C205-1 Power Supply To remove a 7C205‐1 power supply, refer to Figure 3‐10 on page 3‐18 and proceed as follows: 1. Attach the anti‐static wrist strap as described in “Attaching the Electrostatic Discharge Wrist Strap” on page 3‐7 before handling the power supply module.
Replacement Procedures Figure 3-10 Removing a 7C205-1 from a Powered Up Chassis È Ä Ç Å Æ TOP - SLOT 5 SLOT 4 SLOT 3 À SLOT 2 BOTTOM - SLOT 1 AC ON AC ON 0 POWER POWER FAN LINE: 100-125V~12A 200-240V~6A 50/60Hz POE 1 LINE: 100-125V~12A 200-240V~6A 50/60Hz PS 2 PS 1 POE 2 Ã 0 FAN AC INLET 1 AC INLET 3 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz AC INLET 2 AC INLET 4 100 - 125V ~ 15A 200 - 240V ~ 8A 50/60 Hz 100 - 125V ~ 15A 200 - 240V
Replacement Procedures Removing an N-POE PSM To replace an N‐POE PSM in an operating N5 chassis, proceed as follows: Caution: Observe all Electrostatic Discharge (ESD) precautions when handling sensitive electronic equipment. Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de seguridad para evitar descargas de electricidad estática. 1.
Replacement Procedures Removing the Fan Assembly To remove the fan assembly, refer to Figure 3‐11 and proceed as follows: 1. Locate the ESD wrist strap shipped with the N5 chassis. Attach the ESD wrist strap to your wrist and plug the cable from the ESD wrist strap into the ESD grounding receptacle at the upper front‐right corner of the chassis. 2. Use a Phillips screwdriver to loosen the four captive Phillips‐head screws located at each corner of the fan assembly. 3.
Replacement Procedures Installing the Fan Assembly To reinstall the fan assembly, refer to Figure 3‐12 and proceed as follows: 1. Locate the ESD wrist strap shipped with the N5 chassis. Attach the ESD wrist strap to your wrist and plug the cable from the ESD wrist strap into the ESD grounding receptacle at the upper right corner of the chassis. 2. Hold the fan assembly by its two handles. 3. Line up the fan assembly with the four tapped screw holes in the chassis.
Replacement Procedures Figure 3-12 Reinstalling the Fan Assembly À Á Â Ã 1 Captive Phillips-head screws (4) 2 Fan assembly handles (2) 3 Fan assembly 4 Self-aligning power connector 5. Once the tray assembly is in place, tighten the four slotted screws (see Figure 3‐12) to secure the tray to the N5 chassis. 6. Plug the other end of the 20 A power cord into a dedicated 20 A/120 Vac receptacle. Set the 0/| power switch on the front panel of the power supply to |. 7.
A Specifications This appendix provides the specifications for the following: For information about... Refer to page... Matrix N5 Chassis A-2 7C205-1 System Power Supply Module A-3 N-POE-1200W Power Supply Module A-3 7C405 Fan Assembly A-4 AC Power Cord A-5 Torque Values A-5 Environmental Requirements A-6 Regulatory Compliance A-6 Enterasys Networks reserves the right to change the specifications at any time without notice.
Matrix N5 Chassis Matrix N5 Chassis Table A‐1 provides the physical and power specifications for the Matrix N5 Chassis. Table A-1 Matrix N5 Chassis Specifications Item Specification Module Slots Slots 1 through 5 Slots that support all DFE-Gold and DFE-Platinum series modules Power Supply Slots PS 1 and PS 2 Slots for 7C205-1 (1200 W) system power supplies POE 1 through POE 4 Slots for optional N-POE-1200W DC power supply modules Physical Dimensions 62.4 H x 44.1 W x 55.8 D (cm) 24.6 H x 11.
7C205-1 System Power Supply Module 7C205-1 System Power Supply Module Table A‐2 provides the physical and electrical specifications for the 7C205‐1. Table A-2 7C205-1 Specifications Item Specification Physical Dimensions 12.7 H x 21.0 W x 27.94 D (cm) 5.0 H x 8.27 W x 11.0 D (in.) Approximate Weight (Unit) 9.1 kg (20.
7C405 Fan Assembly Table A-3 N-POE-1200W Specifications (continued) Item Specification Physical Dimensions 4.1 H x 12.7 W x 25.4 D (cm) 1.6 H x 5.0 W x 10.0 D (in.) Over-Temperature Protection (OTP) Yes. Protects against • excessive temperatures caused by inadequate (blocked) airflow, • fan failure, or • excessive air inlet temperature. Approximate Weight (Unit) 2.1 kg (4.6 lb) MTBF 247,000 Hours 7C405 Fan Assembly Table A‐4 provides the physical specifications for the 7C405 fan assembly.
AC Power Cord AC Power Cord Any AC power cord used to connect an AC power source to the AC Line connector of a 7C205‐1 AC power supply or N‐POE‐1200W power supply module must meet the specifications listed in Table A‐5. Table A-5 7C205-1 AC Power Cord Specifications Item Specification Cord set approval The cord set must be approved for use by the governing authority in the country of installation. Inlet Connector IEC 320 C19 power cord connector.
Environmental Requirements Environmental Requirements Table A‐7 provides the environmental specifications for the N5 chassis system.
